Memoq MQ-79 User Manual

MQ-79 User's Manual
Ball-point pen Voice Recorder
* We are not responsible for the loss of recordings caused by wrong usage, A/S, other reasons.
* We are not responsible for the damage or third party's claims caused by the usage of this product.
Cautions
* Disassembly, remodeling, impact, the usage in place of low temperature, high temperature, high humidity
in use
can be the cause of failure.
* Please save the important recordings into PC frequently.
* The contents of the User's manual can be changed without notice to improve functionality and performance.
ⓐRecorder ⓑRecording switch
ⓔUSB terminal ⓕRemote controller
ⓙPrevious button
ⓘNext button
ⓜMode button ⓝConnecting jack
Name of
each part
ⓐRecorder
*The product has a built-in battery and can be used after charging. (Charging time : 1 hour)
*Charging starts when the product's ⓔUSB terminal is connected to the PC's USB port or a charging adapter(optional).
Caution : Be sure to use a certified charging adapter (rated output DC5V/500mA or higher).
Damage to the product due to a defective charging adapter may result in paid repair.
Charging
*During charging, the ⓒOperation indicator flashes RED▶BLUE▶GREEN depending on the
battery level and the GREEN LED is turned on when charging is completed
*When the product is disconnected from the PC or USB charging adapter,
the ⓒOperation indicator will display LED for 5 seconds, depending on the battery level.
Battery
*During recording or standby with the remote controller connected, press the ⓜMode button briefly and
the ⓒOperation indicator will display LED for 5 seconds, depending on the battery level.
remains
indication
Operation indicator RED
Battery remains 0~30%
*If you keep the ⓑRecording switch in state of STOP and connect it to the USB port on your PC,
it is recognized as a "Removable disk (MEMOQ)", and copy, movement, deletion, playback of file is possible.
Connecting
*For playback, please use the music playback software of PC.
PC USB
Caution : When you separate product from PC, please be sure to perform " hardware safety removal"
Caution : When you remove product from PC by force, fatal error on product can occur.
ⓒOperation indicator ⓓMicrophone
ⓖEarphone hole ⓗVolume controller
ⓚPlay/Pause button ⓛStop button
ⓝ
ⓑ
ⓒ ⓔ
Earphone
ⓗ
ⓓ ⓖⓘⓙⓚⓛ ⓜ
ⓕRemote controller
USB cable
USB cable ⓒOperation indicator
BLUE GREEN
30~70% 70~100%
How to use
1. Connect a USB cable to the product's ⓔUSB terminal, connect it to the PC's USB port
and run the "TIME SETUP" program stored on the product.
VOS ON/OFF
(Basic setting : VOS Off)
Recording sound quality
(Basic setting : XHQ)
Scheduled recording
(Basic setting : Off)
Time setting
program
DATE_TIME.CFG
creation button
2. After checking the settings according to the usage environment, click the "START" button.
3. If the "DATE_TIME.CFG" file is normally created in the product, disconnect the product from
the USB port to complete the setting.
Caution : The date and time set on the PC are displayed. If the date and time are displayed diffently
please check the PC settings.
Caution : If the product is not separated immediately after clicking the START button, a time error will
occur as much as the delayed time.
Caution : If the product is not separated from the PC after clicking the START button, the setting will not be completed.
1. MODE (Recording Quality)
* Recording sound quality setting.
· PCM(No compression : 705kbps/44.1kHz), XHQ(Ultra high sound quality : 128kbps/32kHz),
HQ(High sound quality : 64kbps/16kHz)
Tip : Higher recording quality improves sound quality, but increases memory and battery usage.
2. VOS ON/OFF
* VOS Recording : If there is no sound during recording, the recording pauses, and when sound is heard,
the recording resumes.
· VOS OFF, VOS ON (VOS recording is turned on/off)
Tip : Unnecessary silent sections are not recorded, saving listening time and memory usage.
Caution : The battery life is the same regardless of VOS ON/OFF, the difference is that it creates
a file by saving only the part where the sound is detected.
Detailed
Caution : There is a risk that it may not be recorded depending on the volume,
explanation of
we recommend VOS OFF recording for important recordings.
time setting
3. VOS LEVEL
program
* Set the volume required to resume recording from a pause during VOS recording.
· +2 Very sensitive(About 52dBA), +1 Sensitive (About 55dBA), 0 Normal (About 58dBA),
-1 Insensitive(About 61dBA), -2 Very insensitive(About 64dBA)
+2 +1
(React to low sound)
Tip : Change the VOS LEVEL setting after testing it according to the location and situation.
4. REC indicator
* Turn on or off the RED LED on the ⓒOperation indicator during recording.
· On (During recording, the LED is displayed every 3 seconds)
· Off (During recording ,the LED is turned off)
VOS Level
V001
(Basic setting : +2)
REC indicator
Mode (Record Quality) VOS On/Off VOS Level REC Indicator MIC Sense
(Basic setting : Off)
VOS Off +2 On High
PCM
+1
Middle
XHQ
VOS On 0 Off
HQ
Low
-1
Microphone sensitivity
-2
Schedule Recording (Basic setting : Middle)
Off
On
Current date and time
2024-01-01 13:00:00
VOS LEVEL
0 -1 -2
Microphone sensitivity (React to loud sound)