Subscribe to Our Youtube Channel
Related Manuals for Projecta INTELLI-START IS3000
Summary of Contents for Projecta INTELLI-START IS3000
- Page 1 INTELLI-START INDUSTRIAL LITHIUM JUMP STARTER Intelli-start.com P/No. IS3000, IS5000...
-
Page 2: Important Safety Information
IMPORTANT SAFETY INFORMATION Please read this manual thoroughly before use and store in a safe place for future reference. WARNINGS • This unit has been designed for vehicles with 12V DC and 24V DC electrical systems only. • Risk of explosive gas. Working in the vicinity of car batteries can be dangerous. Batteries release explosive gases during normal operation, charging and jump starting. -
Page 3: Important Charging Information
IMPORTANT CHARGING INFORMATION • Charge the jump starter prior to use, using the dock. This may take up to 8 hours. • Fully recharge the jump starter after every use to ensure your jump starter is ready for use in case of an emergency. •... - Page 4 DESIGN FOR EASY TRANSPORTATION • With an ergonomically designed handle, the IS3000 & IS5000 jump starters are portable and compact compared to a conventional high-power lead acid jump starters. HIGH PERFORMANCE BATTERY • The high quality 4-cell, 6Ah Lithium Iron Phosphate (LiFePO ) battery delivers instant starting power to petrol and diesel vehicles.
-
Page 5: Surge Protection
BATTERY AND JUMP START STATUS INDICATION • The IS3000 and IS5000 jump starters utilise a coloured LCD display and backlit buttons to inform the user about its status and to support the operation of the jump starter. SURGE PROTECTION • The IS3000 and IS5000 feature built in surge protection so you can safely jump start vehicles with EFI (electronic fuel injection) and computer management systems. -
Page 6: Product Overview
PRODUCT OVERVIEW IS3000 and IS5000 Premium spark Cable and free clamps clamp storage Ergonomic Workshop friendly carry handle heavy duty outer case Docking station On/o 12V jump start selector Jump start Full colour 24V jump start LCD screen selector LCD DISPLAY SCREEN LAYOUT IS3000/IS5000 jump starter battery status. -
Page 7: Jump Starting
JUMPSTARTER INSTRUCTIONS Notes: • Instructions for negatively earthed vehicles only (most vehicles after 1970 are negatively earthed). • Before jump starting a vehicle, it is recommended to ensure the jump starter is fully charged. JUMP STARTING Step Instruction Display The IS3000/IS5000 jump starter should be charged for around 8 hours prior to first use and as soon as possible after each use. -
Page 8: Override Mode
After the engine has started, leave the clamps connected for a minimum of 40 seconds to allow the IS3000/IS5000 RRT to charge the unit. Once the IS3000/IS5000 is fully charged, the RRT will shut off to avoid overcharging. Note: • The IS3000/IS5000 will not switch OFF as long the clamps are connected to the vehicle battery. - Page 9 CHARGING Step Detail Display Plug the output of the AC charging dock into a 240V AC socket. Once the AC dock is plugged into a 240V AC source, you can place the IS3000/IS5000 onto the charging dock. The battery charging screen will be shown when the IS3000/IS5000 is being charged.
-
Page 10: Error And Alarm Messages
UNDERSTANDING YOUR JUMP STARTER ERROR AND ALARM MESSAGES Error type Error detail Error display Low battery The internal battery voltage of the IS3000/IS5000 is too low for a jump start. Please charge the IS3000/ IS5000 immediately. LOW BATTERY Charge jump starter Reverse The clamps are reverse connected to the vehicle polarity... -
Page 11: Frequently Asked Questions
FREQUENTLY ASKED QUESTIONS Why does my IS3000/IS5000 take so long to charge on the dock? Lower charging rate extends the battery life. The built-in charging circuit provides gentle 2-stage charge with cell-balancing for the internal Lithium Iron Phosphate (LiFePO ) battery. Can the IS3000/IS5000 jump start vehicles at temperature lower than 0°C? If the IS3000/IS5000 operates at temperatures below 0°C, its jump start rated performance will be reduced but it will start vehicles with lower clamp output... -
Page 12: Warranty Statement
WARRANTY STATEMENT Brown & Watson International Pty. Ltd. (“BWI”) of 1500 Ferntree Gully Road, Knoxfield, Vic., telephone (03) 9730 6000, fax (03) 9730 6050, warrants that all products described in its current catalogue will under normal use and service be free of failures in material and workmanship for a period of one (1) year from the date of the original purchase by the customer as marked on the invoice (see elsewhere for specific warranty period).
Need help?
Do you have a question about the INTELLI-START IS3000 and is the answer not in the manual?
Questions and answers