Download Print this page
Swatch OMEGA 1640 Manual

Swatch OMEGA 1640 Manual

Advertisement

Quick Links

Description
29 Q LCD CALD S ECL STS A24 CORH CORM CORR CORJ CORMO 2AL TM 2AG RH
Movement height
Frequency
GENERALITIES
DISPLAY numerical, 12 h or 24 h
FUNCTIONS permanently :
hours, minutes, seconds
By selection
chrono 24 h. 1/100th sec.
(Start, Stop, Lap, Split, Reset)
timer (12 h. count-down timer)
appointment alarm (automatically let down)
waking alarm
recall of complete hours (time signal)
agenda 1 and 2 (2 momorized dates)
time zone
day (alphanumerical) and date
lighting of display
BATTERY CHARGE INDICATOR
CORRECTIONS
corrector located et 3 o'clock for time-setting;
pusher and capacity sensor for actual
correction
choice and modification of programmes by
means of capacity sensor and pushers
VARIATION DURING WEAR
better then _ 5 seconds par month
+
(adjust to this degree if necessary)
RESISTANCE TO SHOCKS
NIHS shocks : residual effect recoverable by
means of the frequency corrector
Cal. 1640
C
ALIBRE
1640
0 29.50 mm
/
English
1980
6.20 mm
32'768 A/h
DATE LAUNCHED 1980
DIMENSIONS diameter 29.50 mm
height 6.20 mm (on battery)
RESISTANCE TO MAGNETIC FIELDS
better than 60 Oe
TEMPERATURE FUNCTIONING LIMITS
from 0 to 60˚ C
RUNNING TIME
typical with battery RW 49 25 months with
each day 2 x 30 seconds alarm and 4 lighting
calls of 1 sec.
CONSUMPTION : maxi 5.5 µA
typical 3.6 µA
MINIMUM OPERATING VOLTAGE
_ 1.35 _ V 0.10
+
BATTERY
TYPE silver oxide-zinc (high drain)
DIAMETER 11.60 mm
HEIGHT 3.10 mm
VOLTAGE 1.55 V
CAPACITY RW 49
VARTA 554 85 mAh
REFERENCE SSIH 9926
ELECTRONIC MODULE
TYPE OF RESONATOR quartz tuning fork
FREQUENCY 32768 Hz
FREQUENCY CORRECTOR
TYPE trimmer
100 mAh
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the OMEGA 1640 and is the answer not in the manual?

Questions and answers

Stein B. Evensen
April 18, 2025

Hello, How can I change from am/pm display to 24 hour? (Sensorquartz 1640)

1 comments:
Mr. Anderson
May 9, 2025

To change the display from AM/PM to 24-hour format on the Swatch Sensorquartz 1640, use the setting mode where the time is adjusted. Pass your finger over the sensor toward the "+" or "–" to scroll through options. The display mode (12 h or 24 h) can be selected during this process. Confirm the selection by pressing the CONFIRM button.

This answer is automatically generated

Summary of Contents for Swatch OMEGA 1640

  • Page 1 Description ALIBRE 1640 29 Q LCD CALD S ECL STS A24 CORH CORM CORR CORJ CORMO 2AL TM 2AG RH 0 29.50 mm 6.20 mm Movement height Frequency 32'768 A/h GENERALITIES DATE LAUNCHED 1980 DISPLAY numerical, 12 h or 24 h DIMENSIONS diameter 29.50 mm height 6.20 mm (on battery) FUNCTIONS permanently :...
  • Page 2 DIAGNOSIS REASONS CONTROLS MEASURES ALITEST DISPLAY BLINKS, encased movement 1.55 V probes on "input" touch-piece Contact 24H V Ext DISPLAY OFF, encased movement 1.55 v probes on "input" touch-piece Contact 24H V Ext CONSUMPTION WITH SENSOR, without battery clamp probes on "output" touch-pieces maxi 5.5 µA µA 1.55 V...
  • Page 3 1. INTRODUCTION This new design multifunction calibre has a sensor which is linked to the electronic movement by a connector. In order to be certain which of the 2 components (electronic movement or sensor) is defective when the watch is not running well, the following procedure is recommended: After checking the push-buttons and their contacts, check or replace the battery and clean the + and - clamps.
  • Page 4 4. ORDER OF OPERATIONS (RECOMMENDED IN THE SEQUENCE OF FIGURES 1 TO 15) NOTE : *5. Shiny side up (1640.9803 WHITE) (1640.9814 YELLOW) *7. Soldering on the loft *13. The oblique part of the connector should be on top (see drawing on following page) The following pieces should not, as a rule, be disassembled.
  • Page 5 Position of light bulb on electronic movement. ATTENTION : The light bulb wire must be perfectly vertical on the outside of the electronic module. A groove is made for this wire to pass in the diffuser. 1980 Cal. 1640...
  • Page 6 5. HABILLAGE (CASE, DIAL, HANDS) + Lubrication List of tools : Driving in of crystal base 9085 9084 stake guiding pin Driving out of sensor 9088 base stake 9089 guiding pin limiting tube 9088/01 Driving in of sensor 9082 base stake 9083 guiding pin...
  • Page 7 7. SWITCH Select the 12 hour or 24 hour display by changing the position of the switch 1640.9634 (see drawing). 6. BATTERY EXHAUSTION DETECTOR With a battery voltage below 1.35 V _ 0.10, the display blinks thus indicating the battery's exhaustion, 1 to 3 weeks in advance. 9.
  • Page 8 10. CONTROL OF FUNCTIONS: Display, Sensor, Push Buttons, Programme (abbreviated operating instructions) After each operation, the memories must again be programmed. For all time-setting and programme-selecting functions, the case back should be closed. TIME-SETTING Press the corrector "C", the seconds blink. Press the CONFIRM button, the hour and minutes blink.

This manual is also suitable for:

Omega 1640.9803Omega 1640.9814
Save PDF