Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for CDA HN7750
Summary of Contents for CDA HN7750
- Page 1 HN7750 Induction hob Installation, use and maintenance www.cda.co.uk...
-
Page 2: Table Of Contents
Care and maintenance Please enter the details on the appliance rating plate below for 25 Troubleshooting reference, to assist CDA Customer Care in the event of a fault with Installation your appliance and to register your appliance for guarantee purposes. -
Page 3: Important Information
(EMC) 2014/30/EU. Parts intended to come into contact with food when you remove the pans. conform to 1935/2004/EC. • Do not allow children to play with the appliance nor sit, stand or climb on it. IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE •... -
Page 4: Important Safety Instructions
• Children less than 8 years of age should be kept away unless appliance at any time. continuously supervised. • Please make this information available to the person responsible • This appliance can be used by children aged 8 and above and for installing the appliance. - Page 5 • This appliance complies with electromagnetic safety standards. the regulations that apply to it. As such, CDA guarantee only that our • However, persons with cardiac pacemakers or other electrical product is compliant.
-
Page 6: Saving Energy
Saving energy The best cookware to use with induction cooking has thick flat bases, as the heat will be better distributed meaning cooking is more even. Using energy in a responsible way not only saves money but also Most cookware is compatible with induction cooking. helps the environment. -
Page 7: Hob Layout
Hob layout Using your induction hob Before using your new hob 1800W (boost 2200W) • Read this guide, taking special note of the ‘Safety Warnings’ 1500W 1200W (boost 1800W) section. (boost 1500W) • Remove any protective film that may still be on your induction hob. 1200W 1500W (boost 1500W) - Page 8 glass, wood, porcelain, ceramic and earthenware. the induction hob will automatically switch off. You will need to start • Do not use cookware with jagged edges or a curved base. again at step 1. • Make sure that the base of your pan is smooth, sits flat on the You can touch the heating zone selection again and modify the heat glass and is the same size as the cooking zone.
-
Page 9: Locking The Controls
When you have finished cooking When the hob is in lock mode, all controls are disabled, except the 1. Touch the heating zone selection control that you wish to switch ON/OFF. You can always turn the induction hob off with the ON/OFF off. -
Page 10: Using The Timer
People with a heart pacemaker should consult their doctor NOTE: The red dot next to power level indicator will illuminate, before using this unit. indicating that zone is selected. NOTE: Timer display will show the shortest set time Using the timer Using the bridge zone (maximum power 3000W) •... -
Page 11: Heat Settings
Care and maintenance Cooking guidelines Take care when frying as the oil and fat heat up very quickly, Always disconnect the appliance from the power supply before particularly if you’re using the “Boost” function. undertaking any cleaning or maintenance. At extremely high termperatures oil and fat will ignite spontaneously and this presents a serious fire risk. - Page 12 Remove stains left by melts and sugary food or spillovers as soon as when touching the controls. possible. If left to cool on the glass, they may be difficult to remove or 4. The glass is being scratched. even permanently damage the glass surface. Tough-edged cookware;...
-
Page 13: Troubleshooting
Troubleshooting 9. The induction hob or a cooking zone has turned itself off unexpectedly, a tone sounds and an error code is displayed If an abnormality comes up, the induction hob will automatically enter (typically alternating with one or two digits in the cooking timer the protective state and display corresponding protective codes. -
Page 14: Installation Information
Senor of IGBT thermistor connection error. Or detection part of IGBT PCB sensor failure, send to service center for repairing. IGBT thermistor open circuit In the event of a fault with the hob please advise CDA Customer Care. L (mm) W (mm) H (mm) D (mm) - Page 15 Note: The distance between the hotplate and the cupboard • A suitable isolating switch providing full disconnection from the above should be at least 600mm. mains power supply is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations.
-
Page 16: Mains Electricity Connection
Mains electricity connection Before locating the fixing brackets The unit should be placed on a stable, smooth surface to prevent Warning! This appliance must be earthed. damage. Do not apply force onto the controls protruding from the The appliance must be connected by qualified electrician, who is a hob. -
Page 17: Technical Data
Technical data Caution! Voltage of heating elements 220-240V Recommended Model HN7750FR N1 N2 Caution! In the event type of connection of any connection the safety wire lead Power supply AC 220-240V 50Hz must be connected to the 1500W terminal. Heating area front left (180mm) (Boost 1800W) Heating area rear left (180mm) 1200W (Boost 1500W) - Page 18 For more information please contact: The Sales Department on 01949 862 010 or email sales@cda.co.uk Customer Care Department. The CDA Group Ltd, Harby Road, Langar, Nottinghamshire, NG13 9HY 01949 862 012 F: 01949 862 003 E: customer.care@cda.co.uk...
Need help?
Do you have a question about the HN7750 and is the answer not in the manual?
Questions and answers