Makita DFL126F Instruction Manual
Cordless angle screwdriver
Hide thumbs
Also See for DFL126F:
- Instruction manual (85 pages) ,
- Instruction manual (77 pages) ,
- Instruction manual (45 pages)
Subscribe to Our Youtube Channel
Related Manuals for Makita DFL126F
Summary of Contents for Makita DFL126F
- Page 1 INSTRUCTION MANUAL Cordless Angle Screwdriver DFL126F DFL303F DFL404F Read before use.
-
Page 2: Specifications
Read instruction manual. The typical A-weighted noise level determined accord- ing to EN62841-2-2: Only for EU countries Ni-MH Model DFL126F Due to the presence of hazardous com- Li-ion Sound pressure level (L ) : 79 dB (A) ponents in the equipment, waste electrical... -
Page 3: Declarations Of Conformity
Keep work area clean and well lit. Cluttered or mined according to EN62841-2-2: dark areas invite accidents. Model DFL126F Do not operate power tools in explosive atmo- Work mode: screwdriving without impact spheres, such as in the presence of flammable Vibration emission (a ) : 2.5 m/s... - Page 4 Personal safety Power tool use and care Stay alert, watch what you are doing and use Do not force the power tool. Use the correct common sense when operating a power tool. power tool for your application. The correct Do not use a power tool while you are tired or power tool will do the job better and safer at the under the influence of drugs, alcohol or med- rate for which it was designed.
-
Page 5: Cordless Screwdriver Safety Warnings
Follow your local regulations relating to disposal of battery. 12. Use the batteries only with the products specified by Makita. Installing the batteries to non-compliant products may result in a fire, exces- sive heat, explosion, or leak of electrolyte. 5 ENGLISH... -
Page 6: Functional Description
If you can see the red indicator as causing fires, personal injury and damage. It will shown in the figure, it is not locked completely. also void the Makita warranty for the Makita tool and charger. To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. -
Page 7: Overload Protection
Charge the battery(ies) or replace it/them with recharged battery(ies). 0% to 25% Let the tool and battery(ies) cool down. If no improvement can be found by restoring protection Charge the system, then contact your local Makita Service Center. battery. The battery Switch action may have malfunctioned. -
Page 8: Electric Brake
This tool is equipped with an electric brake. If the electric brake is active but the tool consistently fails to quickly stop after the switch trigger is released, have the tool serviced at a Makita service center. Fig.4 NOTE: An electric brake function can be activated or deactivated in application preferences. - Page 9 LED indicator / Beeper Fig.6 ► 1 . LED indicator LED indicator / Beeper on the tool shows the following functions. Function Status of the tool Status of the LED indicator/beeper Action to be taken LED indicator Beeper Check of the LED indi- When the battery car- Lights up first in green, A series of very short...
- Page 10 If the cord has broken or other indicator does not stop, reasons. ask your local Makita Service Center for repair. Motor or controller failure Motor or controller fail- Blinks in red and green A series of short beeps.
-
Page 11: Selecting Correct Socket
NOTICE: Make sure that the USB cover is closed when operating the tool. NOTE: Use the Makita genuine USB cable to con- nect your computer to the tool. Refer to the section "SPECIFICATIONS". NOTE: For the application software, please contact a Makita sales representative. -
Page 12: Installing Hook
► 1 . Head 2. 45° intervals injury. The hook is convenient for temporarily hanging the tool. DFL126F The hook can be installed in two positions on top of Loosen the lock nut by turning it counterclockwise, the tool handle. To install the hook, widen the arms of as shown in the figure, using a wrench. -
Page 13: Operation
Loosen the lock sleeve by turning it counterclock- wise, as shown in the figure, using a hook wrench. Hold the tool firmly and place the socket over the bolt or nut. Then switch the tool on. When the clutch activates, the motor will stop automatically. Then release the switch trigger. DFL126F Fig.18 ► 1 . Lock sleeve 2. Hook wrench Fig.21 13 ENGLISH... -
Page 14: Maintenance
1. Range of fastening capacity 2. Rotation angle cracks may result. 3. Torque To maintain product SAFETY and RELIABILITY, For model DFL303F repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 360° 300° 240° 180°... -
Page 15: Optional Accessories
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. - Page 16 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885A59-228 20240116...
Need help?
Do you have a question about the DFL126F and is the answer not in the manual?
Questions and answers