Using The Product With A Laser Receiver (Receiver Mode); Connecting The Product To The Parkside App - Parkside PKLLP 3360 A1 Short Manual

LED
5 ] [
Green
Flashes red
3 . Release the button
4 . Press the button
9 ] [
opening for left vertical 360° laser line
5 . Press the button
9 ] [
both the opening for left vertical 360° laser line
opening for front vertical 360° laser line
6 . Press the button
[ 9 ]
are projected .
11 ] [
7 . Switching off: Press and hold the
LED goes off . The laser leveler LED
5 ] [
˜ Using the product with a laser receiver
(receiver mode)
INFO:
A laser receiver is not included in the scope of delivery .
o
When working with a laser receiver, the receive mode must
o
always be activated . This is independent of whether you are
using the automatic or manual leveling function .
In receiver mode, the laser lines flash at a very high frequen‑
o
cy . This enables a laser receiver to detect the laser lines .
When the receiver mode is switched on, the laser lines are
o
less visible to the human eye .
Always switch off the receiver mode after you finish working
o
with the laser receiver .
Refer to the user manual of the laser receiver for details on
o
how to use and how to set up the laser receiver .
Switching on
Press the receiver mode button
o
LED lights up green .
8 ] [
Switching off
Press the receiver mode button
o
LED goes off .
8 ] [
˜ Connecting the product to the
PARKSIDE app
˜ Activate/deactivate the Bluetooth
function on the battery
1 . Press and hold the
for 3 seconds to activate the Bluetooth
LED of the charging level LEDs
function is enabled .
36 GB/IE
02_448696_2301_Short_GB.indd 36 02_448696_2301_Short_GB.indd 36
Charging level
Medium to maximum
Low
.
9 ] [
. The laser line is projected from the
.
[ 10 ]
again . The laser line is projected from
and the
[ 10 ]
.
[ 11 ]
again . All 360° laser lines /
[ 1 ] 10 ] [
button until the
9 ] [
goes off .
3 ] [
. The receiver mode
7 ] [
. The receiver mode
[ 7 ]
®
button on the battery pack
26 ] [ 25 ] [
function . The orange
®
lights up . The Bluetooth
[ 27 ]
2 . Release the button
3 . Press and hold the
for 10 seconds to deactivate the Bluetooth
orange LED of the charging level LEDs
function is deactivated . In the PARKSIDE app the
Bluetooth
®
product is shown as offline .
˜ Connecting the product to the
PARKSIDE app
INFO:
/
You can operate the product via your home Wi‑Fi network or
o
manually without a Wi‑Fi network .
The PARKSIDE app is required to control and set up the
o
product via your home Wi‑Fi network .
The PARKSIDE app supports the operating systems iOS 9 .0,
o
Android 5 .0 or higher .
The product can only be connected to the PARKSIDE app if
o
the battery pack
[ 25 ]
Only Smart Performance rechargeable batteries can be
o
connected to the PARKSIDE app .
1 . Press and hold the
for 3 seconds to activate the Bluetooth
2 . Enable the Bluetooth
Open the PARKSIDE app .
3 .
Connecting the product for the first time to the
PARKSIDE app
{Add a tool}
1 . Select
PARKSIDE app scans the area for available devices . The
PARKSIDE app indicates if available devices have been
found .
2 . Tap on the product name to select the battery pack
{Done}
3 . Tap to confirm the connection . The battery pack
is listed in the {Your
4 . Select the battery pack
product can be found in the
pack is installed on the product .
5 . Switch on the product in automatic or manual leveler function
(see "Using the automatic/manual leveler function") . The
connection status LED
®
.
[ 26 ]
button on the battery pack
26 ] [
function . The
®
goes off . The
[ 27 ]
is inserted in the product .
button on the battery pack
26 ] [
function .
®
function on your smartphone .
®
{Your tools} tab . The
or on the
[ 25 ]
tools} tab and can be selected .
. The information about the
[ 25 ]
{Your tools} tab, if the battery
lights up in blue .
4 ] [
7/10/2023 6:07:18 PM 7/10/2023 6:07:18 PM
25 ] [
25 ] [
.
25 ] [