Setting/Hanging Up The Laser Target Plate; Using The Automatic Leveler Function; Using The Manual Leveler Function - Parkside PKLLP 3360 A1 Short Manual

Clamping the universal mount
(Fig . D)
1 . Push down the clamp handle
2 . Fix the universal mount
object .
3 . Release the clamp handle
4 . Adjusting the vertical height of the clamp part
hold the locking buttons
clamp part . Release the locking buttons .
Mounting the universal mount
(Fig . K)
1 . Slide the clamp part
[ 34 ]
from the universal mount part
2 . Fix the universal mount part
metal surface .
Hanging the universal mount
Use the wall hanging hole
o
on a wall .
Mounting the universal mount
INFO: A tripod is not included in the scope of delivery .
Mount a tripod on the Internal thread of the universal mount
o
(6 .35 mm) or on the internal thread of the universal
39 ] [
mount (15 .8 mm)
40 ] [
˜ Setting/hanging up the laser target
plate
(Fig . L)
INFO:
The laser target plate
o
beam under unfavorable conditions and at large distances .
The reflective part of the laser target plate
o
visibility of the laser line .
The laser line is also visible from the back side of the laser
o
target plate .
[ 36 ]
Setting up the laser target plate
1 . Unfold the laser target plate back stand
2 . Place the laser target plate
stand .
[ 38 ]
Hanging the laser target plate
Use the laser target plate magnet
o
plate on a metal surface .
[ 36 ]
02_448696_2301_Short_GB.indd 35 02_448696_2301_Short_GB.indd 35
on a pipe or plate
15 ] [
to open the clamp jaw
[ 18 ]
on a pipe, a plate or a similar
[ 15 ]
.
18 ] [
: Push and
34 ] [
. Adjust the vertical height of the
[ 17 ]
on a metal surface
15 ] [
downwards to remove the clamp part
.
35 ] [
with the magnets on a
35 ] [ [ 33 ]
on a wall
[ 15 ]
to hang the universal mount
24 ] [
on a tripod
15 ] [
.
increases the visibility of the laser
36 ] [
improves the
36 ] [
on a flat surface
36 ] [
.
[ 38 ]
on the laser target plate back
[ 36 ]
on a metal surface
36 ] [
to fix the laser target
37 ] [
˜ Operation
CAUTION! Risk of injury!
Laser beam ‒ Do not look into the openings for laser
.
16 ] [
lines /
1 ] [ [ 10 ]
eyes to prevent looking into the laser beam . Risk of
eye injury!
˜ Using the automatic leveler function
INFO:
In the event of vibrations, the product levels itself
o
automatically . Wait until the laser lines no longer move .
Working with automatic leveler function: The laser leveler
o
LED does not have any function .
[ 3 ]
The laser line is projected from the opening for horizontal
o
360° laser line
[ 1 ]
1 . Place the main unit
Alternatively, you can also fasten the main unit to the universal
mount (see "Using the universal mount") .
15 ] [
2 . Switching on: Slide the leveling slide switch
[ 15 ]
the position .
The LED lights up:
5 ] [
LED
[ 5 ]
Green
Flashes red
3 . Press the button
opening for left vertical 360° laser line
4 . Press the button
both the opening for left vertical 360° laser line
opening for front vertical 360° laser line
5 . Press the button
are projected .
11 ] [
6 . Switching off: Slide the leveling slide switch
the position . The
˜ Using the manual leveler function
INFO:
Working without the automatic leveler: The laser leveler
o
LED illuminates permanently in red .
[ 3 ]
The laser lines depicted are not leveled .
o
1 . Switching on: Slide the leveling slide switch
the position .
2 . Press and hold the
from the horizontal opening
The laser leveler LED
The LED lights up:
5 ] [
/ ! Turn your head away or close your
11 ] [
.
on a horizontal, solid surface .
2 ] [
to the left to
[ 6 ]
Charging level
Medium to maximum
Low
. The laser line is projected from the
[ 9 ]
.
[ 10 ]
again . The laser line is projected from
[ 9 ]
10 ] [
.
[ 11 ]
again . All 360° laser lines
[ 9 ] 1 ] [
to the right to
6 ] [
LED goes off .
[ 5 ]
to the right to
6 ] [
button until the 360° laser line
9 ] [
is projected .
1 ] [
lights up in red .
[ 3 ]
GB/IE
7/10/2023 6:07:18 PM 7/10/2023 6:07:18 PM
and the
/ /
10 ] [
35