Page 1
Maintenance and Service Guide HP Elite SFF 600 G9 Desktop PC SUMMARY This guide provides maintenance information about such topics as spare parts, removal and replacement of parts, security, and backing up.
Table of contents 1 Product features..............................................1 Front panel components .......................................... 1 Rear panel components .......................................... 2 Connecting external Wi-Fi antennas ....................................3 Serial number location ..........................................3 2 Illustrated parts catalog..........................................5 Computer major components......................................5 Miscellaneous parts............................................7 3 Routine care, drive guidelines, and disassembly preparation........................... 9 Electrostatic discharge information....................................
Page 4
4 Removal and replacement procedures....................................19 Preparation for disassembly......................................19 Access panel ..............................................20 Battery................................................20 Optical drive..............................................22 Front bezel............................................... 23 Hard drives ..............................................24 Speaker................................................27 WLAN module............................................... 28 Solid-state drive............................................30 Memory modules (DIMMs)........................................31 Expansion card............................................34 Fan duct ................................................35 Fan hood................................................36 Heat sink................................................37 Processor ................................................38...
Page 5
The computer boots to DOS after making a bootable flash drive....................63 Solving internet access problems ....................................63 Unable to connect to the internet..................................63 Cannot automatically launch internet programs............................64 Solving software problems.........................................64 Computer will not start up and the HP logo does not appear......................64 “Illegal Operation has Occurred” error message is displayed......................64...
Page 6
9 Backing up, restoring, and recovering....................................97 Backing up information and creating recovery media............................97 Using Windows tools for backing up..................................97 Using the HP Cloud Recovery Download Tool to create recovery media (select products only)......97 Restoring and recovering your system..................................98 Creating a system restore ......................................98 Restoring and recovery methods ..................................98...
Page 7
Downloading HP PC Hardware Diagnostics UEFI to a USB flash drive.................108 Downloading the latest HP PC Hardware Diagnostics UEFI version................108 Downloading HP PC Hardware Diagnostics UEFI by product name or number (select products only) .............................................109 Using Remote HP PC Hardware Diagnostics UEFI settings (select products only)..............109 Downloading Remote HP PC Hardware Diagnostics UEFI ......................109...
Product features This chapter provides you with an overview of your computer's features. Front panel components To identify the front panel components, use these illustrations and tables. NOTE: Drive configuration varies by model. Some models have a bezel blank that covers one or more drive bays.
The combo jack supports headphones, line output devices, microphones, line input devices, CTIA-style headsets, and OMTP-style headsets. NOTE: Your model might have additional components available from HP. NOTE: The light on the power button is normally white when the power is on. If the light blinks red, the computer displays a diagnostic code to indicate a problem.
Dual-mode DisplayPort™ monitor connectors NOTE: Your model might have additional ports available from HP. When a graphics card is installed in one of the system board slots, you can use the video connectors on the graphics card or the integrated graphics on the system board. The specific graphics card installed and software configuration determine the behavior.
Use this information to determine the spare parts that are available for the computer. NOTE: HP continually improves and changes product parts. For complete and current information about supported parts for your computer, go to https://partsurfer.hp.com/partsurfer/, select your country or region, and then follow the on-screen instructions.
Page 13
Table 2-1 Computer major components and their descriptions (continued) Item Description Memory modules (DDR5-4800, 1. 1 V, NECC, UDIMM): 32 GB 16 GB 8 GB 8 GB (NSW Dep. of E&C; locked) System board ADL-Q670, MT22 (includes replacement thermal material): Equipped with the NetC and Windows®...
Mini DisplayPort–to–DisplayPort adapter Optical drive bay adapter USB–to–serial adapter Expansion card: HP PCIe×1 parallel port expansion card IO1 DisplayPort B2B expansion card IO1 HDMI B2B expansion card IO1 2× USB Type-A 3G1 B2B expansion card IO1 USB Type-C® B2B expansion card...
Page 15
Hood sensor module (includes cable) Locks: HP dual-head keyed cable lock HP keyed cable lock (10 mm) Power cord: Power cord, C13, 1.83 m (6.0 ft) conventional with sticker Power cord, C13, 2.0 m (6.6 ft) conventional with sticker for use in India...
Routine care, drive guidelines, and disassembly preparation This information provides general service information for the computer. Adherence to the procedures and precautions is essential for proper service. IMPORTANT: When the computer is plugged into an AC power source, DC voltage is always applied to the system board.
Table 3-1 Static electricity occurrence based on activity and humidity Relative humidity Event Walking across carpet 7,500 V 15,000 V 35,000 V Walking across vinyl floor 3,000 V 5,000 V 12,000 V Motions of bench worker 400 V 800 V 6,000 V Removing DIPs (dual in-line packages) from plastic tube 400 V...
● Use field service tools, such as cutters, screwdrivers, and vacuums, that are conductive. Recommended materials and equipment HP recommends these materials and equipment to prevent static electricity. ● Antistatic tape ● Antistatic smocks, aprons, or sleeve protectors ●...
● Conductive tote boxes ● Opaque shielding bags ● Transparent metallized shielding bags ● Transparent shielding tubes Operating guidelines This information details how to prevent overheating and to help prolong the life of the computer. ● Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold. ●...
Keep liquids away from the product. Avoid getting moisture in any openings. If liquid makes its way inside your HP product, it can cause damage to the product. Do not spray liquids directly on the product. Do not use aerosol sprays, solvents, abrasives, or cleaners containing hydrogen peroxide or bleach that might damage the finish.
Keep liquids away from the product. Avoid getting moisture in any openings. If liquid makes its way inside your HP product, it can cause damage to the product. Do not spray liquids directly on the product. Do not use aerosol sprays, solvents, abrasives, or cleaners containing hydrogen peroxide or bleach that might damage the finish.
To clean the tops of the keys or the keyboard body, follow the procedures described in Cleaning the computer case on page When cleaning debris from under the keys, review all rules in General cleaning safety precautions on page 12 before following these procedures.
The screws used in the computer are not interchangeable. They could have standard or metric threads and might be of different lengths. If you use an incorrect screw during the reassembly process, it can damage the unit. HP strongly recommends that you keep all screws that you remove during disassembly with the removed part and then return them to their proper locations.
Data transfer rate 6.0 Gbps Always use an HP-approved SATA 6.0 Gbps cable because it is fully backwards compatible with the SATA 1.5 Gbps drives. Current HP desktop products ship with SATA 6.0 Gbps hard drives. SATA data cables are susceptible to damage if overflexed. Never crease a SATA data cable and never bend it tighter than a 30 mm (1.18 in) radius.
Page 25
● Do not bend any cable sharply. A sharp bend can break the internal wires. ● Never bend a SATA data cable tighter than a 30 mm (1. 1 8 in) radius. ● Never crease a SATA data cable. Chapter 3 Routine care, drive guidelines, and disassembly preparation...
Not all features listed in this guide are available on all computers. NOTE: HP continually improves and changes product parts. For complete and current information about supported parts for your computer, go to https://partsurfer.hp.com/partsurfer/, select your country or region, and then follow the on-screen instructions.
Do not expose to temperatures higher than 60°C (149°F). ● Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water. ● Replace the battery only with the HP spare part that is designated for this product. Chapter 4 Removal and replacement procedures...
Page 28
You can extend the lifetime of the lithium battery by plugging the computer into an AC outlet. The lithium battery is used only when the computer is not connected to AC power. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, go to http://www.hp.com/recycle.
To release the battery from its holder, squeeze the metal clamp (1) that extends above one edge of the battery. When the battery (2) pops up, lift it out. With the positive side up, insert the battery (1) onto the battery socket at an angle, and then press the battery (2) down until it locks into place.
Table 4-1 Optical drive descriptions Description DVD+/-RW SM DL 9.5 mm with slim tray DVD-ROM 9.5 mm with slim tray Slim optical drive bezel Slim optical drive blank bezel Before removing the optical drive, follow these steps: Prepare the computer for disassembly (see Preparation for disassembly on page 19).
Position the computer with the front toward you. Disengage the tabs (1) on the top of the front bezel from the slots in the system chassis. Swing the front bezel (2) down and away from the system chassis. Remove the front bezel. To install the front bezel, reverse the removal procedure.
Page 32
Slide the hard drive to the left (2), and remove the hard drive from the front chassis. Press and hold the front chassis release tabs (1). Swing the rear edge of the front chassis (2) up and forward. Disconnect the hard drive power cable (3) from the hard drive. Disconnect the hard drive data cable (4) from the hard drive.
Page 33
Slide the hard drive to the left (2), and remove the hard drive from the front chassis. Pull and hold the hard drive release lever (1). Slide the hard drive to the left (2), and remove the hard drive from the front chassis. Chapter 4 Removal and replacement procedures...
Release the optical drive data cable from the retention clip that is built into the front chassis. Release the hard drive cables from the retention clips (1) and (2) that are built into the front chassis. Disconnect the hard drive power cable (3) from the system board. Disconnect the hard drive data cables (4) from the system board.
Remove the optical drive (see Optical drive on page 22). Remove the front bezel (see Front bezel on page 23). Remove the speaker: Disconnect the speaker cable (1) from the system board. Release the speaker cable from the retention clip (2) that is built into the system chassis. Release the speaker clips from the rubber retention posts (3) that are built into the system chassis.
Page 36
Remove the optical drive (see Optical drive on page 22). Remove the front bezel (see Front bezel on page 23). Remove the WLAN module: Remove the Phillips screw (1) that secures the module and the WLAN module bracket to the computer.
To install the WLAN module, reverse the removal procedure. NOTE: WLAN modules are designed with a notch to prevent incorrect insertion. Solid-state drive To remove the solid-state drive module, use these procedures. Table 4-4 Solid-state drives descriptions Description 2 TB, M.2 2280, PCIe–4×4, ZTurbo solid-state drive with TLC 1 TB, M.2 2280, PCIe–4×4, NVMe solid-state drive with TLC 1 TB, M.2 2280, PCIe, NVMe, value solid-state drive 512 GB, M.2 2280, PCIe–4×4, NVMe solid-state drive with TLC...
Remove the screw that secures the drive (1). Pull the drive out of the system board connector (2). To install the solid-state drive module, reverse the removal procedure. NOTE: Solid-state drive modules are designed with a notch to prevent incorrect insertion. Memory modules (DIMMs) To remove the memory modules, use this information and procedures.
Page 39
Table 4-5 Memory module descriptions (continued) Description 8 GB (DDR5-4800, 1. 1 V, NECC, UDIMM) memory module The memory sockets on the system board are populated with at least one preinstalled memory module. To achieve the maximum memory support, you can populate the system board with up to 128 GB of memory configured in a high-performing dual-channel mode.
Page 40
● The system operates in flex mode if the total memory capacity of the DIMMs in channel A is not equal to the total memory capacity of the DIMMs in channel B. In flex mode, the channel populated with the least amount of memory describes the total amount of memory assigned to dual channel, and the remainder is assigned to single channel.
To install a memory module, open both latches of the memory module socket (1), and insert the memory module into the socket (2). Press the module down into the socket so that the module is fully inserted and properly seated. Be sure that the latches are in the closed position (3). NOTE: You can install a memory module in only one way.
Remove the front bezel (see Front bezel on page 23). To remove an expansion card: Remove the Phillips screw (1) that secures the expansion card bracket to the expansion card. Release the expansion card bracket (2) from the expansion card. Release the slot cover retention latch (3) that secures the slot covers by lifting the tab on the latch and rotating the latch to the open position.
Remove the fan duct: Swing the fan duct (1) up and back until it rests at an angle. Slide the fan duct (2) forward to detach the clips from the tabs that are built into the rear chassis. Remove the fan duct (3). To install the fan duct, reverse the removal procedure.
Remove the fan hood (2). To install the fan hood, reverse the removal procedure. Heat sink To remove the heat sink, use these procedures. IMPORTANT: The bond between the heat sink and the processor can be very tight. If the computer will turn on, before removing the heat sink, turn on the computer until it warms the heat sink.
IMPORTANT: For optimum thermal performance, be sure not to touch the thermal grease on the surface of the processor or the heat sink. Thoroughly clean the thermal material from the surfaces of the heat sink and the system board components each time the heat sink is removed. Replacement thermal material is included with the heat sink and system board spare part kits.
Page 46
Prepare the computer for disassembly (see Preparation for disassembly on page 19). Remove the access panel (see Access panel on page 20). Remove the optical drive (see Optical drive on page 22). Remove the front bezel (see Front bezel on page 23).
After installing a new processor onto the system board, always update the system ROM to ensure that the latest version of the BIOS is being used on the computer. You can find the latest system BIOS on the web at: https://support.hp.com/us-en. Power supply To remove the power supply, use these procedures.
Disconnect the power supply P3 (5) cable from the system board. Remove the three Phillips screws (1) that secure the power supply to the computer. Press and hold the power supply release tab (2). Slide the power supply toward the front of the system chassis (3), and then remove the power supply (4).
Page 49
Prepare the computer for disassembly (see Preparation for disassembly on page 19). Remove the access panel (see Access panel on page 20). Remove the optical drive (see Optical drive on page 22). Remove the front bezel (see Front bezel on page 23).
Remove the six Torx15 screws that secure the system board to the system chassis. Remove the system board by lifting it straight up. To install the system board, reverse the removal procedures. NOTE: When replacing the system board, you must change the chassis serial number in the BIOS. When replacing the system board, you must reprogram the SMBIOS information about the affected computer.
Page 51
Remove the access panel (see Access panel on page 20). Remove the optical drive (see Optical drive on page 22). Remove the front bezel (see Front bezel on page 23). Remove the wireless antennas: Disconnect the AUX antenna cable from the WLAN module (1). Release the AUX antenna cable from the retention clip (2) that is built into the system chassis.
Page 52
Release the MAIN antenna cable from the routing channel (2) that is built into the system chassis. Press down on the tab (1) on the transceiver cover, and then remove the cover (2) by swinging the top edge down and away from the system chassis. Remove the slotted Torx screw (3) that secures the MAIN antenna transceiver to the system chassis.
Boot the computer to the Safe Mode to see if it will boot without all of the drivers loaded. When booting the operating system, use “Last Known Configuration.” ● See the comprehensive online technical support at http://www.hp.com/support. Access HP Business Solutions at https://www.hp.com/us-en/solutions/business-solutions.html...
● Spend time troubleshooting the problem with the service technician. ● Restore the system from the Recovery Disc Set that you created or restore the system to its original factory condition in System Software Requirement Disks (SSRD). IMPORTANT: Restoring the system will erase all data on the hard drive. Be sure to back up all data files before running the restore process.
sure to disconnect the power cord from the AC outlet and allow the internal system components to cool before touching. Cannot access the Computer Setup (F10) Utility when booting the computer Use this information to troubleshoot the computer. Cause Solution The Computer Setup (F10) Utility is set to Before turning on the computer, press and hold f10.
In case of forgotten password, power loss, or computer malfunction, you must manually disable the Smart Cover lock. A key to unlock the Smart Cover Lock is not available from HP. Keys are typically available from a hardware store. Poor performance Use this information to troubleshoot the computer.
Some software applications, especially Lower the display resolution for the current application or consult games, are stressful on the graphics the documentation that came with the application for suggestions subsystem. on how to improve performance by adjusting parameters in the application.
Cause Solution System unable to power on. Press and hold the power button for fewer than 4 s. If the hard drive light turns white: If the computer has a voltage selector, check that the voltage selector (located on the rear of the power supply) is set to the appropriate voltage.
Cause Solution Processor thermal protection activated. A fan Be sure that the computer air vents are not blocked and the might be blocked or not turning, or the heat processor cooling fan is running. sink is not properly attached to the processor. Open the access panel, press the power button, and see if the processor fan (or other system fan) spins.
Cause Solution Either the directory structure is bad or there is In Windows, type file in the taskbar search box, and then select File a problem with a file. Explorer from the list of applications. In the left column, expand This PC, right-click a drive, select Properties, and then select the Tools tab.
Cause Solution The device is attached to a SATA port that has Check SATA cable connections. been hidden in Computer Setup. Run the Computer Setup utility, and be sure that Device Available is selected for the device's SATA port in Advanced > Port Options. Boot order is not correct.
Computer is in the Sleep state. Press the power button to resume from the Sleep state. IMPORTANT: When attempting to resume from the Sleep state, do not hold down the power button for more than 4 seconds. Otherwise, the computer will shut down, and you will lose any unsaved data. Internal speaker is disabled in Computer Enable the internal speaker in Computer Setup.
If you are on a network, you might not have Make the proper network connections to the printer. made the connection to the printer. Printer might have failed. Run printer self-test. The printer might be out of paper. Check the paper tray, and refill it if it is empty. Printer will not turn on Use this information to troubleshoot the computer.
Computer is in the Sleep state. Press the power button to resume from the Sleep state. IMPORTANT: When attempting to resume from the Sleep date, do not hold down the power button for more than 4 seconds. Otherwise, the computer will shut down, and you will lose any unsaved data. Mouse does not respond to movement or is too slow Use this information to troubleshoot the computer.
Replace DIMMs one at a time to isolate the faulty module. NOTE: DIMM1 or XMM1 must always be installed. DIMM1 must be installed before DIMM3. Replace third-party memory with HP memory. Replace the system board. Chapter 5 Troubleshooting without diagnostics...
Solving network problems Some common causes and solutions for network problems are listed in these tables. The guidelines do not discuss the process of debugging the network cabling. Network driver does not detect network controller Use this information to troubleshoot the computer. Cause Solution Network controller is disabled.
Cause Solution The cable is not securely connected. Be sure that the cable is securely attached to the network connector and that the other end of the cable is securely attached to the correct device. The cable is attached to the incorrect Be sure that the cable is attached to the correct connector.
For those systems that support error correction code (ECC) memory, HP does not support mixing ECC and non-ECC memory. Otherwise, the computer will not boot the operating system.
Memory is installed incorrectly or is bad. Reseat DIMMs. Turn on the system. Replace DIMMs one at a time to isolate the faulty module. Replace third-party memory with HP memory. Replace the system board. Solving USB flash drive problems If you encounter USB flash drive problems, common causes and solutions are listed in these tables.
System will not boot from USB flash drive Use this information to troubleshoot the computer. Cause Solution Boot order is not correct. Run the Computer Setup utility, and change the boot sequence in Advanced > Boot Options. Removable Media Boot is disabled in the Run the Computer Setup utility, and enable booting to removable media in Computer Setup utility.
If you encounter software problems, see the applicable solutions listed in the following table. Computer will not start up and the HP logo does not appear Use this information to troubleshoot the computer. Cause Solution ROM issue - POST error has occurred.
Computer Setup (F10) Utility This information provides details of the Computer Setup Utility. ● Change settings from the defaults or restore the settings to default values. ● View the system configuration, including settings for processor, graphics, memory, audio, storage, communications, and input devices. ●...
Repeatedly press when the power button light turns white to access the utility. You can also press to see a menu that allows you to access different options available at startup, including the Computer Setup utility. A choice of four headings appears in the Computer Setup Utilities menu: Main, Security, Advanced, and UEFI Drivers.
Page 74
Table 6-1 Computer Setup Main Option Description System Information Lists all information in following list if Advanced System Information is selected. Lists smaller subset if Basic System Information is selected. ● Product name ● Installed memory size ● Processor type ●...
Page 75
Description System Diagnostics If the hard drive has the HP Advanced Diagnostics installed, the application launches. If HP Advanced Diagnostics is not installed, a basic version that is built into the BIOS provides the capability to perform the following functions: ●...
Page 76
Check for Update on Next Reboot: Default is disabled. ● BIOS Source: Lets you select either HP.com or a custom URL. If Custom URL is selected, Edit Custom URL becomes active. HP recommends using a custom URL only for a managed IT environment.
Update BIOS Using Local Media Lets you access files on either USB storage or the hard drive. The HP BIOS Update and Recovery application included in BIOS Softpaqs at www.hp.com copies the BIOS file to the correct location on the hard drive or USB device.
Page 78
Table 6-2 Computer Setup Security Option Description Create BIOS Lets you set and enable a BIOS administrator password, which controls access to the following Administrator Password features: Setup Menu (F10) ● ● Third-Party Option ROM Management (F3) ● Update system ROM ●...
Page 79
Manual recovery is intended only for situations when you want forensic analysis before HP Sure Start recovery. When this policy is set to manual, HP Sure Start will not correct any issues that are found until the local user enters the manual recovery key sequence. This can result in a computer that cannot boot until the manual recovery key sequence is entered.
Page 80
HP firmware, while the operating system is running. – Log Event Only: HP Sure Start will log all critical security events in the HP Sure Start audio log within the HP Sure Start nonvolatile (flash) memory.
Page 81
● SPM Current State: Displays the current state. Also lets you change the state. ● Unprovision SPM: Deprovisions SPM, which causes HP Sure Run to revert to the inactive state and return HP Sure Recover to default settings. ● HP Sure Run Current State: Displays the current state. Also lets you change the state.
Page 82
Table 6-2 Computer Setup Security (continued) Option Description Utilities Hard Drive Utilities ● Save/Restore GPT of System Hard Drive Enabling this feature saves the GUID Partition Table (GPT) of the system hard drive. If the GPT is subsequently changed, the user is prompted to choose whether to restore GPT. Default is disabled.
Computer Setup Advanced This table provides information about the Computer Setup Advanced menu. NOTE: Support for specific Computer Setup options can vary, depending on the hardware configuration. Table 6-3 Computer Setup Advanced (for advanced users) Option Heading Display Language Lets you select the language of the menus in F10 Setup and the keyboard layout. Scheduled Power-On This feature wakes the system when it is off at a specified date and time.
Page 84
Recover before Boot Failure Recovery If enabled and HP Sure Recover is launched because of a boot failure, the user is notified of the boot failure and asked to choose whether to start or cancel HP Sure Recover. This setting is displayed only if Recover after Boot Failure is selected.
Page 85
Table 6-3 Computer Setup Advanced (for advanced users) (continued) Option Heading System Options Configure storage controller for Intel Optane™ (Intel products only) Enables the Intel Optane™ memory module. Configure storage controller for RAID Enables RAID. Default is enabled. Limit PCIe Speed (workstation models only) Lets you restrict the maximum speed of the PCI Express devices to previous generations.
Page 86
Provides ACPI structure to enable HP common software application framework. The driver is provided in the latest HP support software that you can download from the web. NOTE: Device Manager shows an alert if this setting is enabled without the HP application driver installed. AMD DASH Lets you enable AMD Remote system management capability.
Page 87
Table 6-3 Computer Setup Advanced (for advanced users) (continued) Option Heading Built-In Device Options Embedded LAN Controller (select products only) Select to show the device in the operating system. Default is enabled. Wake On LAN Lets you either disable the Wake On LAN feature or configure where the computer boots, including the network or hard drive.
Page 88
Increase Idle Fan Speed (%) Increases the minimum fan speeds over the normal settings while still enabling normal control using the internal thermal sensors. Force enable HP Sure View Enables the HP Sure View privacy panel by changing the screen brightness. Computer Setup Advanced...
Page 89
Table 6-3 Computer Setup Advanced (for advanced users) (continued) Option Heading Port Options USB ports (varies by model) Lets you enable specific USB ports. Default is enabled. USB Legacy Port Charging Lets you enable USB charging port capability when the computer is in hibernate or shutdown mode. Default is enabled.
Page 90
Table 6-3 Computer Setup Advanced (for advanced users) (continued) Option Heading Power Management Runtime Power Management Options Allows certain operating systems to reduce processor voltage and frequency when the current software load does not require the full capabilities of the processor. Default is enabled. Extended Idle Power States Allows certain operating systems to decrease the processors power consumption when the processor is idle.
Page 91
Table 6-3 Computer Setup Advanced (for advanced users) (continued) Option Heading Remote Management Active Management Technology (AMT) Options (Intel only) Allows you to discover, repair, and protect networked computing devices. Default is enabled. USB Key Provisioning Support Enables AMT provisioning using a USB storage device. Default is disabled. USB Redirection Support USB redirection allows USB devices plugged into a client computer to be transparently redirected to the guest operating system.
Page 92
Sets the configuration for Remote HP PC Hardware Diagnostics, including the URLs used for download and upload and scheduled execution frequency. Execute Remote HP PC Hardware Diagnostics Select to immediately execute Remote HP PC Hardware Diagnostics based on the how settings are configured. Any unsaved BIOS settings will be lost. Computer Setup Advanced...
POST error messages This section lists the error codes, error messages, and the various indicator light and audible sequences that you may encounter during Power-On Self-Test (POST) or computer restart, the probable source of the problem, and steps you can take to resolve the error condition. POST Message Disabled suppresses most system messages during POST, such as memory count and non-error text messages.
Page 94
Table 7-1 POST numeric codes and text messages Control panel message Description Recommended action 002-Option ROM Checksum Error System ROM or expansion board option Verify the correct ROM. ROM checksum. Flash the ROM if needed. If an expansion board was recently added, remove it to see if the problem remains.
Page 95
Table 7-1 POST numeric codes and text messages (continued) Control panel message Description Recommended action 00B-MEBx Module did not checksum Memory error during POST execution Reboot the computer. correctly of the Management Engine (ME) BIOS Unplug the power cord, reseat the Extensions option ROM.
Page 96
Drive Protection System test under using F2 Diagnostics when booting the computer. Apply hard drive firmware patch if applicable. (Available at http://www.hp.com/support.) Back up contents and replace hard drive. POST numeric codes and text messages...
Page 97
F2 Diagnostics when booting the computer. Apply hard drive firmware patch if applicable. (Available at http://www.hp.com/support.) Back up contents and replace hard drive. 309 – 30C: Hard Disk 3–6: SMART Hard Hard drive will soon fail. (Some hard...
Page 98
Table 7-1 POST numeric codes and text messages (continued) Control panel message Description Recommended action 402-Serial Port C Address Conflict Both external and internal serial ports Remove any serial port expansion Detected are assigned to the same resources. cards. Clear CMOS. Reconfigure card resources and/or run Computer Setup or Windows utilities.
Table 7-1 POST numeric codes and text messages (continued) Control panel message Description Recommended action 900-CPU Fan Not Detected CPU fan is not connected or might have Reseat fan. malfunctioned. Reseat fan cable. Replace fan. 901-Chassis, Rear Chassis, Front Fan is not connected or might have Reseat fan.
Page 100
to disconnect the power cord from the AC outlet and allow the internal system components to cool before touching. During the system validation phase that occurs at system startup, the BIOS validates the functionality of the following subsystems and conditions: ●...
Page 101
The red LED blinks to represent the major error category (long blinks). The white LED blinks to represent the minor error category (short blinks). For example, ‘3.5’ indicates 3 long red blinks and 5 short white blinks to communicate the processor is not detected. Table 7-3 Interpreting POST diagnostic front panel lights and audible codes Category...
Back up the BIOS settings or save them as custom defaults in case you need them later. You can back up in Computer Setup or with the BiosConfigUtility tool available from www.hp.com. See Computer Setup (F10) Utility on page 65 for information about backing up the BIOS settings.
Deleting a setup or power-on password Use this procedure to delete a password. To delete the power-on or setup password, complete the following steps: Turn on or restart the computer. To delete the Setup password, go to step 2. To delete the Power-on password, go to step 3. To delete the Setup password, as soon as the computer turns on: - Press while the “Press the ESC key for Startup Menu”...
Backing up, restoring, and recovering You can use Windows tools or HP software to back up your information, create a restore point, reset your computer, create recovery media, or restore your computer to its factory state. Performing these standard procedures can return your computer to a working state faster.
Recovering using HP Recovery media You can use HP Recovery media to recover the original operating system and software programs that were installed at the factory. On select products, it can be created on a bootable USB flash drive using the HP Cloud Recovery Download Tool.
Restoring and recovery methods on page 98 to restore your computer before you obtain and use the HP recovery discs. Using a recent backup can return your machine to a working state sooner than using the HP recovery discs. After the system is restored, reinstalling all the operating system software released since your initial purchase can be a lengthy process.
No applications, features, or functionality were added to or installed on the system. Following system shutdown and removal of all power sources from an HP business computer system, personal data can remain on volatile system memory (DIMMs) for a finite period of time and also remains in nonvolatile memory.
Page 108
Select the Security menu, select Restore Security Settings to Factory Defaults, and then select Yes to restore security level defaults. The computer restarts. During the restart, press while the "Press the ESC key for Startup Menu" message is displayed at the bottom of the screen. NOTE: If the system has a BIOS administrator password, type the password at the prompt.
System boot ROM (BIOS) Non-volatile memory, 128 Mbit Download the latest BIOS (16 MB) socketed, removable for your model from the HP website and follow the instructions to flash the BIOS that are on the website RTC (CMOS) RAM Volatile memory, 256 bytes...
HP has provided options in Computer Setup (BIOS) to allow you to run in legacy BIOS, if required by the operating system. Examples of this requirement would be if you upgrade or downgrade the OS.
Those select computer models ship with HP Sure Start configured and enabled. HP Sure Start is configured and already enabled so that most users can use the HP Sure Start default configuration. Advanced users can customize the default configuration.
Select the box next to the 24-digit failure ID to copy your failure code and send it to support. Accessing HP PC Hardware Diagnostics Windows After HP PC Hardware Diagnostics Windows is installed, you can access it from HP Support Assistant or the Start menu.
To stop a diagnostic test, select Cancel. Accessing HP PC Hardware Diagnostics Windows from Support Assistant After HP PC Hardware Diagnostics Windows is installed, follow these steps to access it from HP Support Assistant. Type support in the taskbar search box, and then select the HP Support Assistant app.
Downloading HP PC Hardware Diagnostics UEFI to a USB flash drive on page 108. If your PC does not start in Windows, you can use HP PC Hardware Diagnostics UEFI to diagnose hardware issues. Using an HP PC Hardware Diagnostics UEFI hardware failure ID code When HP PC Hardware Diagnostics UEFI detects a failure that requires hardware replacement, a 24-digit failure ID code is generated.
For assistance in solving the problem, complete one of these tasks: ● Select Contact HP, accept the HP privacy disclaimer, and then use a mobile device to scan the failure ID code that appears on the next screen. The HP Customer Support - Service Center page appears with your failure ID and product number automatically filled in.
Find out more. Downloading Remote HP PC Hardware Diagnostics UEFI Remote HP PC Hardware Diagnostics UEFI is also available as a SoftPaq that you can download to a server. Downloading the latest Remote HP PC Hardware Diagnostics UEFI version You can download the latest Remote HP PC Hardware Diagnostics UEFI version to a USB flash drive.
Set the location for downloading the diagnostic tools. This feature provides access to the tools from the HP website or from a server that has been preconfigured for use. Your computer does not require the traditional local storage (such as a hard drive or USB flash drive) to run remote diagnostics.
Power cord set requirements The power supplies on some computers have external power switches. The voltage select switch feature on the computer permits it to operate from any line voltage of 100 V AC to 120 V AC or 220 V AC to 240 V AC. Power supplies on those computers that do not have external power switches are equipped with internal switches that sense the incoming voltage and automatically switch to the proper voltage.
Country-specific requirements This information provides additional requirements specific to a country. Table 12-1 Power cord country-specific requirements Country Accrediting Agency Country Accrediting Agency Australia (1) EANSW Italy (1) Austria (1) Japan (3) METI Belgium (1) CEBC Norway (1) NEMKO Canada (2) Sweden (1) SEMKO Denmark (1)
DC power source, it should be powered only with an AC adapter or a DC power source supplied and approved by HP for use with this computer. The computer can operate on DC power within one or more of the following specifications. The voltage and current for your computer is located on the regulatory label.
Setup password 96 heat sink with fan illustrated 5 backup, creating 97 helpful hints 47 backups 97 HP PC Hardware Diagnostics UEFI electrostatic discharge (ESD) 9 battery downloading 108 preventing damage 9, 10 disposal 9, 15, 16 failure ID code 107...
Page 122
59 USB flash drive 98 illustrated 5 nonvolatile memory 100 recovery media 97 removal and replacement 27 numeric error codes 86 creating using HP Cloud static electricity 9 Recovery Download system board Tool 97 illustrated 5 creating using Windows...
Page 123
Windows backup 97 recovery media 97 system restore point 97 Windows tools, using 97 wireless antennas removal and replacement 43 WLAN module removal and replacement 28 Index...
Need help?
Do you have a question about the Elite SFF 600 G9 and is the answer not in the manual?
Questions and answers