Advertisement
Quick Links
STAR
Quick installation and programming guide
This quick guide summarises the full installation manual. The full manual contains safety warnings and other
explanations that must be taken into account. You can download the latest version of this guide and the
installation manual in the "Downloads" section of the Erreka website:
http://www.erreka.com.
IMPORTANT
The options and functions described in this guide are applicable from the firmware version indicated on the
NOTE
circuit. As part of a process of continuous improvement, the firmware is subject to the incorporation of new
functionalities or their extension, and consequently to the generation of new versions not necessarily
compatible with the previous ones. Therefore, if your firmware version is lower than the one indicated in this
guide, some options and functions may not be available or may be different.
ELECTRICAL CABLING:
Element
A: Main power supply
B: Traffic light
C: Photocells (Tx/ Rx)
D: Pushbutton
E: Operator / Limit switches
F/G: Flashing light / antenna
Elements of the complete installation
Nº threads x section
2
ST910C: 3x1.5mm
; ST1530C / ST2030C: 3x1.5mm
2
or 5x1.5mm
depending on the control panel and connections
2
3x0.5mm
2
2
2x0.5mm
/ 4x0.5mm
2
2x0.5mm
2
2
4x1mm
/ 5x0.5mm
2
2x0.5mm
/ coaxial cable 50k (RG-58/U)
E349A
Maximum length
2
2
, 4x1.5mm
30m
20m
30m
25m
20m
20m / 5m
English
9
Advertisement
Related Manuals for Erreka STAR ST910C
Summary of Contents for Erreka STAR ST910C
- Page 1 This quick guide summarises the full installation manual. The full manual contains safety warnings and other explanations that must be taken into account. You can download the latest version of this guide and the installation manual in the "Downloads" section of the Erreka website: http://www.erreka.com.
- Page 2 Dimensions (mm) ST910C / ST1530C 27,2 C349A ST2030C 4xM10 4xM10 *: supplied with 1" – 25.4mm adapter C349C...
-
Page 3: Technical Characteristics
Technical characteristics ST910C ST1530C ST2030C 230/50 3x400/50 or 3x230/50 Power supply (V/Hz) Power (W) Capacitor (μF) Maximum torque (Nm) Speed (r.p.m.) Output shaft diameter (mm) 25.4 (includes adapter 25.4 mm) Locking Manual operation Chain drive Limit switches Yes, 20 turns output shaft Duty cycle S3 (%) Thermal protector (ºC) Noise (dB) -
Page 4: Manual Operation
Manual operation OPENING: to open the door manually, pull on the chain in accordance with arrow A (it is not necessary to unlock the operator or to relock it). The chain should move vertically so as not to damage the operator (both in opening and in closing). - Page 5 ST910C single-phase connections with AM606 control panel Operator parts ST910C: ST910C Single-phase motor Capacitor FCA: Opening limit switch FCC: Closing limit switch FCS: Additional limit switch (to be used in accordance with the requirements of the customer or installation) AM606S Thermal protector Unlock switch Control board parts (AM606S):...
- Page 6 ST910C single-phase connections with VIVO-M101PT control panel The VIVO-M101PT control panel allows use of single-phase The VIVO-M101PT control panel is a variant of the VIVO- operators with power above that allowed with the VIVO- T101 control panel that can be used with single-phase M101 panel.
- Page 7 Three-phase ST1530C and ST2030C connections with VIVO-T101 control panel VIVO-T101 ST1530C / ST2030C P349W Operator parts (ST1530C, ST2030C): Operator connections (ST1530C, ST2030C): Three-phase motor U-phase motor FCA: Opening limit switch V-phase motor FCC: Closing limit switch W-phase motor FCS: Additional limit switch (to be used in accordance Earth connection with the requirements of the customer or Neutral motor...
- Page 8 Three-phase ST1530C and ST2030C connections with VIVO-I103 control panel Change the ST1530C and ST2030C settings, switching from 3x400V to 3x230V, connecting the cables as follows: U1: blue U1: blue + brown V1: black V1: black + green W1: white W1: white + grey brown + green + gray wireless ST1530C / ST2030C...
Need help?
Do you have a question about the STAR ST910C and is the answer not in the manual?
Questions and answers