1:10 scale 2wd electric off road competition short course kit (26 pages)
Summary of Contents for Associated Electrics RC10DS
Page 2
• Adjustable height body mounts :: Additional :: Additional Your new RC10DS comes as a kit. There are some items you will need Tools included: to complete your kit (refer to website for suggestions): • Allen wrenches (.035”, .050”, 1/16”, 3/32”) •...
Page 4
This symbols indicates a line up your hardare with the correct drawing special note or instruction until you find the exact size. in the manual. Associated Electrics, Inc. Customer Service 21062 Bake Parkway Tel: 949.544.7500 Lake Forest, CA 92630 Fax: 949.544.7501 http://www.AssociatedElectrics.com •...
Page 5
Nose Plate / Steering Build Steering Build - Bag A - Bag A - - Step 3 Step 3 LEFT 8823 Shock Mount 8823 6299 RC10DS E-clip Front Arm (small) 6271 Ballstud .20 (silver) 7813 RC10T king pin (.125 x 1.11)
Page 6
4-40 nut thin Dust cover 4-40 x 3/8” SHCS 8822 RC10DS front bulkhead blocks (left, right) :: Nose Plate / Nose Plate / Steering Build Steering Build - Bag A - Bag A - - Step 5 Step 5...
Page 7
- Bag A - - Step 7 Step 7 7805 #4 Aluminum RC10 washer chassis, black 4-40 x 3/4 SHCS 8821 RC10DS nose tubes 4-40 nut 6931 8-32 x 1/4 4-40 x 1/4 steel 4-40 x 5/16” SHCS FHCS BHCS...
Page 8
:: Nose Plate / Nose Plate / Steering Build Steering Build - Bag A / F - Bag A / F - - Step 10 Step 10 6279 Ball cups (white) 6260 Turnbuckle (1.00”) Steering Turnbuckle 0.53” (13.5mm) Build left and right sides! :: Front Anti-Roll Bar / Bumper Front Anti-Roll Bar / Bumper Build Build - Bag B...
Page 9
Build - Bag B - Bag B - - Step 3 Step 3 4-40 8822 locknut Front body post 8822 RC10DS front bumper 6316 4-40 x 1/2 FHCS 4-40 x 1/2 FHCS :: Servo / Battery Tray Servo / Battery Tray Build...
Page 10
Rear End Build Build - Bag D - Bag D - - Step 1 Step 1 6273 7810 8831 Dust Ballstud RC10T rear RC10DS cover .20 (silver) hub carrier, rear stub 0 degree axle (Left & Right) 4-40 nut 1/4 axle...
Page 11
:: Rear End Rear End Build Build - Bag D - Bag D - - Step 3 Step 3 6323 Dust RC10 rear cover bulkhead 6273 Ballstud .30 (silver) 6316 8-32 x 1/2 steel 4-40 x 1/2 FHCS SHCS :: Rear End Rear End Build Build - Bag D / F - Bag D / F - - Step 4...
Page 12
:: Rear End Rear End Build Build - Bag D - Bag D - - Step 6 Step 6 8822 Rear body post 8822 RC10DS rear shock tower 4-40 x 5/8 SHCS 4-40 x 3/4 SHCS 4-40 nuts :: Rear End...
Page 13
:: Shocks Build Shocks Build - Bag E - Bag E - Step 2 - Step 2 6420 / 6421 Off-road shock internals 5407 Red o-ring Shock body, Place on table front (0.56) and push down Gold hard until clamp snaps into place Remove SNAP!
Page 14
:: Shocks Build Shocks Build - Bag E - Bag E - Step 5 - Step 5 *Ride height setting may change due to varying weight Shock of batteries and electronics clip Front: 6mm Front arms level Rear: 6mm Rear dogbones Front shock just below level spring...
Page 16
5-40 hub, outer BHCS 3/16 x 5/16 Locknut :: Transmission Build Transmission Build - Bag G - Step 5 8831 RC10DS Dogbone 4-40 x 1/4 BHCS 4-40 x 3/8 Build left and right sides! FHCS :: Transmission Build Transmission Build - Bag G...
Page 17
Battery not included! 6332 Body clip :: Tires Build Tires Build - Bag H - Bag H - Step 1 - Step 1 included! 8829 8827 RC10DS RC10DS front tire front wheel 8829 8827 RC10DS RC10DS front tire front insert...
Page 18
:: Tires Build Tires Build - Bag H - Bag H - Step 2 - Step 2 included! 8829 RC10DS 8827 rear tire RC10DS rear 8829 wheel RC10DS 8827 rear tire RC10DS insert front wheel cap Build 2 :: Tires Build...
Page 19
Body Build - Step 1 Painting Tips: Your RC10DS Kit comes with a clear polycarbonate body and wing. You will need to prep the body and wing before you can paint them. Wash the inside thoroughly with warm water and liquid detergent. Dry the body and wing using a clean, soft, lint-free cloth.
Need help?
Do you have a question about the RC10DS and is the answer not in the manual?
Questions and answers