1:10 scale 2wd electric off road competition buggy kit (26 pages)
Summary of Contents for Associated Electrics RC10 4WD
Page 2
• 5.5” High Downforce Lexan Race Wing Included :: Additional :: Additional Your new RC10 4WD Kit comes as a kit. There are some items you will need to com- Tools included: plete your kit (refer to website for suggestions): •...
Page 4
This symbols indicates a line up your hardare with the correct drawing special note or instruction until you find the exact size. in the manual. Associated Electrics, Inc. Customer Service 21062 Bake Parkway Tel: 949.544.7500 Lake Forest, CA 92630 Fax: 949.544.7501 http://www.AssociatedElectrics.com •...
Page 5
:: Nose Plate / Steering Build - Bag A - Step 1 :: Nose Plate / Steering Build - Bag A - Step 1 7811 #8 aluminum RC10 body washer (thick) mounts 6530 RC10 4WD Washers are used 6530 to adjust to your nose plate, preffered body RC10 4WD Gold height.
Page 6
- Bag B - - Step 3 Step 3 6575 *It is important to tighten your RC10 4WD Ball diffs x2 so they don’t slip. As you tighten the diff bolt, you will notice the T-nut ears Diff thrust moving closer to the bottom of the outdrive slot. This compresses the spring behind the T-nut.
Page 8
6539 6539 RC10 4WD RC10 4WD RC10 4WD 6533 belt tensioner transmission transmission RC10 4WD belt tensioner pulley spacer, case and cover case and cover pulley spacer, outer inner :: Rear Transmission Rear Transmission Build Build - Bag B - Bag B - - Step 3...
Page 9
Locknut :: Front Suspension Build Front Suspension Build - Bag C - Bag C - Step 2 - Step 2 6532 RC10 4WD front transmission case, gasket 4-40 x 1/4 BHCS 6207 RC10 front arm mounts, (Left & Right)
Page 10
Front Suspension Build - Bag C - Bag C - Step 4 - Step 4 6543 6543 coupler 4-40 x 3/32” 6543 set screw RC10 4WD front cva bone, 6543 74mm RC10 4WD cvd coupler cross pin 6543 RC10 4WD...
Page 11
Front Suspension Build - Bag C - Bag C - Step 6 - Step 6 91676 21587 Caster hat 3x14mm 6543 bushings, RC10 4WD BHCS roll pin 6543 RC10 4WD 91676 12mm hex Caster hat bushings, Build left and right sides!
Page 12
- Step 3 Belt tension notes / setup: *Set the belt tensioner as tight as possible without binding the drivetrain. 6542 RC10 4WD drive belt :: Rear Bulkhead :: Rear Bulkhead Build Build - Bag D - Bag D - Step 4...
Page 13
:: Rear Bulkhead :: Rear Bulkhead Build Build - Bag D - Bag D - Step 5 - Step 5 7811 4-40 x 1/4 4-40 x 1/2 RC10 body SHCS SHCS mount #8 aluminum #4 aluminum washer (thick) washer 6593 RC10WC transmission brace...
Page 14
Build left and right sides! :: Turnbuckle Build - Bag F - Step 1 :: Turnbuckle Build - Bag F - Step 1 6547 6535 Note the direction RC10 4WD RC10 4WD of the ball cups! turnbuckle, ball cups, 3.5mm x 38mm 3.5mm...
Page 15
:: Turnbuckle Build - Bag F - Step 2 Note the direction 6547 6535 of the ball cups! RC10 4WD RC10 4WD turnbuckle, ball cups, 3.5mm x 48mm 3.5mm Steering Turnbuckle 1.18” (30.00mm) Orient the notch to the left throughout the car.
Page 16
:: Shocks Build Shocks Build - Bag G - Bag G - Step 2 - Step 2 Front Rear Shock Shock 5407 6437 6435 Red o-ring FT Hard FT Hard Place on table Anodized Anodized and push down hard until clamp shock body, shock body, snaps into place...
Page 17
:: Shocks Build Shocks Build - Bag G - Bag G - Step 5 - Step 5 Due to various weights of electronics, these settings are approximate Front: 5mm (arms level) Rear: 3mm (dog bones level) 6497 Front shock RC10 shock spring, blue collar (4.20lb)
Page 18
Build left and right sides! :: Chassis Build Chassis Build - Bag H - Step 2 6538 4-40 x 1/2 4-40 x 1/2 BHCS SHCS 6538 RC10 4WD Battery not thumb screw included! 6538 6538 O-ring RC10 4WD battery tray...
Page 19
Electronics Build - - Bag I Bag I - Step 1 - Step 1 7811 Servo not RC10 included! servo mounts 6547 RC10 4WD Ball cups, turnbuckle, black 4-40mm x 19mm Note the direction of the ball cups! Servo Turnbuckle 0.19” (5.00mm)
Page 20
Bag J - Step 1 - Step 1 Clean the tire and wheel bead. 6544 Carefully apply CA glue (tire adhesive) RC10 4WD to the tire bead on both sides. 2.2” front Do one side at a time, allow it to dry tire...
Page 21
:: Wheels / Tires and Body :: Wheels / Tires and Body - - Bag J Bag J - Step 4 - Step 4 Painting Tips: 6159 RC10 Protech Your RC10 Kit comes with a clear polycarbonate body and wing. Buggy body, You will need to prep the body and wing before you can paint unpainted...
Page 22
:: Wheels / Tires and Body :: Wheels / Tires and Body - - Bag J Bag J - Step 7 - Step 7 6639 6332 6332 Wing Body Body mounts clip clip 6159 RC10 Protech body, clear 6182 High downforce wing, 5.5”...
Page 23
:: Wheels / Tires and Body :: Wheels / Tires and Body - - Bag J Bag J - Step 10 - Step 10 TIP: Bend wire to create tight fit inside wing tubes.
Need help?
Do you have a question about the RC10 4WD and is the answer not in the manual?
Questions and answers