Page 1
Operation Husky™ Husky™ 2200 Husky™ 2200 2200 Air Air - - - Operated Operated Operated Diaphragm Pump Pump Diaphragm Diaphragm Pump 3A2578F Polypropylene and and PVDF PVDF pumps pumps for for fluid fluid transfer transfer applications, applications, including including high high viscosity viscosity materials.
Warnings Warnings Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings.
Page 4
Warnings WARNING WARNING WARNING EQUIPMENT EQUIPMENT EQUIPMENT MISUSE MISUSE HAZARD MISUSE HAZARD HAZARD Misuse can cause death or serious injury. • Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component.
Page 5
Warnings WARNING WARNING WARNING BURN BURN BURN HAZARD HAZARD HAZARD Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe burns: • Do not touch hot fluid or equipment. PERSONAL PROTECTIVE PROTECTIVE EQUIPMENT EQUIPMENT PERSONAL PERSONAL PROTECTIVE EQUIPMENT...
To Order Order Replacement Replacement Parts Parts Order Replacement Parts ordering information, as needed. 3. Please call Graco Customer Service to order. Please call call your your distributor. distributor. Please Please call your distributor.
Configuration Number Matrix Configuration Number Number Matrix Matrix Configuration Configuration Number Matrix Check the identification plate (ID) for the Configuration Number of your pump. Use the following matrix to define the components of your pump. 2200P - - - PP01AP1PPPTFKPT PP01AP1PPPTFKPT 2200P 2200P...
25 % of the outlet working pressure. selecting and installing system components. Contact 3. Reduce liquid velocity: Slow the cyclic rate of your Graco distributor for assistance in planning a the pump. system to suit your needs. Always use Genuine Graco Parts and accessories.
Page 9
Installation Accessories/Components Accessories/Components Not Accessories/Components Not Supplied Supplied Supplied System System Components System Components Components Air supply line Air inlet port (not visible) Bleed-type master air valve (may be Air exhaust port and muffler required for your pump) Air filter/regulator assembly Fluid inlet port Fluid outlet port Master air valve (to isolate the...
Installation Ground The The System System Air Lines Lines Ground Ground System Lines 1. Install an air filter/regulator assembly (C). The regulator controls the fluid pressure. The fluid stall pressure will be the same as the setting of the air regulator. The filter removes harmful dirt and moisture from the compressed air supply.
Installation Air Exhaust Exhaust Ventilation Ventilation Exhaust Ventilation To provide provide provide a a a remote remote exhaust: remote exhaust: exhaust: 1. Remove the muffler (U) from the pump air exhaust port (K). 2. Install a grounded air exhaust hose (S) and If pumping toxic fluids, you must vent the exhaust connect the muffler to the other end of the hose.
Installation Fluid Outlet Outlet Line Line Fluid Fluid Outlet Line 2. If the inlet fluid pressure to the pump is more than 25% of the outlet working pressure, the ball check valves will not close fast enough, 1. Use grounded, flexible fluid hoses. See resulting in inefficient pump operation.
Installation Flange Connections Connections Flange Flange Connections The fluid inlet and outlet ports are 2 in. (50 mm) raised face, ANSI/DIN PN 10 flanges. Connect 2 in. (50 mm) plastic pipe flange to the pump as follows. You will need: •...
Operation Operation Operation Operation Pressure Relief Relief Procedure Procedure Pressure Pressure Relief Procedure 3. Place the suction tube (if used) in fluid to be pumped. Follow the Pressure Relief Procedure NOTE: NOTE: NOTE: If fluid inlet pressure to the pump is more whenever you see this symbol.
Maintenance Maintenance Maintenance Maintenance Maintenance Schedule Schedule Flushing and and Storage Storage Maintenance Maintenance Schedule Flushing Flushing Storage Establish a preventive maintenance schedule based on the pump’s service history. Scheduled maintenance is especially important to prevent spills or leakage due to diaphragm failure. Lubrication Lubrication Lubrication...
Torque Instructions Torque Instructions Instructions Torque Torque Instructions If fluid cover or manifold fasteners have been Inlet Inlet Inlet and and Outlet Outlet Manifold Outlet Manifold Screws Manifold Screws Screws loosened, it is important to torque them using the following procedure to improve sealing. NOTE: Fluid cover and manifold fasteners have a NOTE: NOTE:...
Dimensions Dimensions Dimensions Dimensions End Flange Flange Models, Flange Models, Models, Polypropylene Polypropylene Polypropylene and PVDF PVDF PVDF Polypropylene PVDF Polypropylene PVDF Polypropylene Polypropylene PVDF PVDF Polypropylene Polypropylene PVDF PVDF A A A 25.1 in. 63.8 cm 25.2 in. 64.0 cm G G G 19.8 in.
Page 19
Dimensions Center Flange Flange Models, Models, Polypropylene Polypropylene Center Center Flange Models, Polypropylene Only Only Only Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene Polypropylene A A A G G G 24.1 in. 61.2 cm 18.5 in. 47.0 cm B B B 27.2 in. 69.1 cm H H H 7.0 in.
Technical Data Technical Data Data Technical Technical Data Husky 2200 2200 Diaphragm Diaphragm Pump Pump Husky Husky 2200 Diaphragm Pump Metric Metric Metric Maximum fluid working pressure 125 psi 0.86 MPa, 8.6 bar Air pressure operating range 20 to 125 psi 0.14 to 0.86 MPa, 1.4 to 8.6 bar...
Page 23
California Proposition 65 Maximum Maximum Maximum pump pump pump speed speed speed 125 cycles per minute Standard diaphragms Overmolded diaphragms 155 cycles per minute Weight Weight Weight Polypropylene 80 lb 36.3 kg PVDF 106 lb 48.1 kg Wetted Wetted Wetted Parts Parts Parts plus the...
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts.
Need help?
Do you have a question about the Husky 2200 and is the answer not in the manual?
Questions and answers