Assa Abloy Corbin Russwin TH9M57 Installation Instructions

OUTSIDE
DOOR FACE
"X"
3-5/8
(92)
2-1/16
(52)
3-5/8
(92)
"X"
9-15/16
(252)
HOLES MARKED "X"
METAL DOORS:
Inside Face
Outside Face
WOOD DOORS:
Dimensions given in Inches
5 "X" HOLES
(See Chart)
Branding Guidelines For Installation Instruction Sheets
Endorsed Logo
* Must Be Used On All Single Page and Multiple Page Installation Instruction Sheets
7/8
(22)
Group Brand Tagline
* Must Be Used On The Bottom Left Of ALL ONE PAGE Installation Instruction Sheets
* Must Be Used On The Bottom Left Of ALL INSIDE PAGES of Multiple Page Installation Instruction Sheets
* It is NOT USED On The Back Page Or Back Cover Of Installation Instruction Sheets
* Image Must Be Used - CANNOT Be Typed
TRIM
TEMPLATE
11/16 11/16
(17.5) (17.5)
"X"
1-1/2 (38) Dia.
1-3/8 (35) Deep
VERTICAL
REFERENCE
C L
( Trim)
C L
HORIZONTAL
REFERENCE
C L
(Device and Trim)
"X"
11/16 11/16
(17.5) (17.5)
(5 Places)
5/16" (8) Dia.
1/2" (13) Dia.
1/2" (13) Dia. Thru
(mm)
"X"
3/8 (9.5) Dia.
Branding Guidelines For Installation Instruction Sheets
3/4 (19) Deep
Endorsed Logo
* Must Be Used On All Single Page and Multiple Page Installation Instruction Sheets
Installation Instructions
1. Check box contents. See other side for components.
2. After marking door inside face for device location (Device Instructions),
transfer "Vertical Reference Centerline" from inside to outside door
face. Follow steps 2a. and 2b. below.
3. Transfer "Horizontal Reference Centerline" from inside to outside door
face.
4. Align trim template and tape to door outside face.
CAUTION: Office copiers and facsimile machines may change the
size of a drawing and make the template inaccurate to use as a door
marker. If this is not the original template packed with the trim, use
only the dimensions written on the template to locate the holes on
the door (do not use the template as a door marker).
5. Spot holes and prepare door for trim.
6. Mount trim to door thru holes "B". Fasten, finger tight only, with
3 screws (b) and washers (c), seating on door as shown in Figure 1.
7. Thread cylinder into mortise lock until seated within escutcheon
recess with keyway positioned vertically and with plug in lower
cylinder as shown in Figure 1. Tighten cylinder locking screw thru
mortise lock front.
8. Continue as shown in device instructions.
(3) screws and
washers bolt trim to
door using holes "B".
Figure 1
Branding Guidelines For Installation Instruction Sheets
Endorsed Logo
* Must Be Used On All Single Page and Multiple Page Installation Instruction Sheets
Group Brand Tagline
* Must Be Used On The Bottom Left Of ALL ONE PAGE Installation Instruction Sheets
* Must Be Used On The Bottom Left Of ALL INSIDE PAGES of Multiple Page Installation Instruction Sheets
* It is NOT USED On The Back Page Or Back Cover Of Installation Instruction Sheets
* Image Must Be Used - CANNOT Be Typed
* Must Be Used On All Single Page and Mul
Group Brand Tagline
* Must Be Used On The Bottom Left Of ALL
* Must Be Used On The Bottom Left Of ALL
* It is NOT USED On The Back Page Or Ba
* Image Must Be Used - CANNOT Be Typed
Corporate Statement
* Must Be Used On The BACK PAGE Or BA
* Image Must Be Used - CANNOT Be Typed
* A 2 line Version and a 5 Line Version Of
Copyright Statement
* Must Be Used On The Bottom of ALL ON
* Must Be Used On The Bottom of The BAC
* Copy Can Be Typed
Copyright © 2008 Corbin Russwin, Inc., an
Reproduction in whole or in part without the
Note: Marketing will continue to be pa
Device is bolted to trim using holes
"A" (closest to door look edge).
3"
TH9M57
(76)
Nightlatch
Function
TH9M57
Heavy Duty Thumbpiece Trim
Installation Instructions
For use with ED5600 Series Mortise Exit Device
(Metal, Wood or Composite Doors)
FM262 11/18 (617417705)
RHR
Door
Shown
10-1/4
(260)
16-5/8
(422)