Advertisement
Quick Links
Installation Instructions - Kurba
Models KBS-W-XX, KBM-W-XX, KBL-W-XX, KBX-W-XX, KBL-PL-XX, KBL-SN-XX
Please read all instructions prior to installation and keep for future reference!
1. PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
2. USE ONLY WITH CLASS 2 POWER UNIT
3. 24 VOLTS DC
4. SUITABLE FOR WET LOCATIONS, SAUNA, POOL RATED
Kurba Horizontal
5. POOL-RATED KURBA SHOULD BE INSTALLED WITH ARTICLE 680
6. NO ADHESIVE ALLOWED TO AFFIX THE PRODUCT
Please read all instructions prior to installation and keep for future reference!
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
OF NFPA 70, "NATIONAL ELECTRICAL CODE" (NEC)
REV0.5
07252024
/
1
10
Kurba Vertical
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
info@luminii.com
www.luminii.com
Advertisement
Related Manuals for luminii Kurba
Summary of Contents for luminii Kurba
- Page 1 6. NO ADHESIVE ALLOWED TO AFFIX THE PRODUCT info@luminii.com 4. SUITABLE FOR WET LOCATIONS, SAUNA, POOL RATED www.luminii.com Please read all instructions prior to installation and keep for future reference! Kurba Horizontal Kurba Vertical *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE...
- Page 2 CAUTION: Reference to below before installing Kurba 2.5“ When unpacking Kurba, carefully pull it out of the packaging box. Do not pull the cable, otherwise it may disable the function of the connector and Note: Incorrect unpacking may cause PCB fracture or damage on electronic lead to water ingression.
- Page 3 NOTE: Keep a 0.39" - 0.79" spacing between the end of the fixture and the mounting channel Once the location or pattern is determined for Kurba to be installed, start off by marking the area. Amount of brackets may vary dependant upon pattern. Reference diagrams below.
-
Page 4: Mounting Brackets
NOTE: Keep a 0.39" - 0.79" spacing between the end of the fixture and the mounting bracket Once the location or pattern is determined for Kurba to be installed, start off by marking the area. Amount of brackets may vary dependant upon pattern. Reference diagrams below. - Page 5 C .4 grip mounting grip surface Fix the rest in sequence along with the marks. Adjust the serrate silicone tape and remove the extra lengths at both ends. *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE...
- Page 6 Fix the screw starting from the power input end. Keep some distance between the channel and power input. C .3 screw mounting channel kurba pool rated C .4 mounting surface Secure the channel with screws Insert kurba to mounting channel. *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE...
- Page 7 (minimum) 8”away (maximum) Curved run with mounting brackets Carefully push the Kurba onto the channel or mounting brackets using your palms, then press in completely to secure in place. Kurba mounting channel Make sure the angle between the light and profile is not bigger than 15°, otherwise When light length longer than 6ft, make sure somebody helps to Kurba might be damaged.
- Page 8 Carefully guide the power feed from kurba through the channel. If needed, carefully join the two channels by join plate. Secure Make sure the powerfeed goes under retaining bracket (factory join plate by tighten the screws.
- Page 9 Use screws to secure inner channel with retaining bracket. endcap kurba kurba raceway mounting channel Carefully insert kurba LED, make sure powerfeed go through the powerfeed hole on end cap. Then use screw to install end caps. *LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE...
- Page 10 To remove Kurba fixture from mounting bracket, gently push a FLAT head screw driver between the BOTTOM of the fixture and the mounting bracket, carefully pry up the Kurba Fixtrure. Once Kurba fixture has started coming out of the bracket, stop using the screw driver and instead use your hands and fingers to pull the fixture out of the bracket making sure to keep it at a 15°...
Need help?
Do you have a question about the Kurba and is the answer not in the manual?
Questions and answers