Installing Batteries In The Remote Control; Using The Remote Control; Configuring Speakers (Sp Config Menu) - Insignia NS-AV511 User Manual

Rocketboost Network Capabilities
The maximum number of Rocketboost devices in a
Rocketboost Network is nine. If you already have
nine and attempt to join an additional device,
joining will fail for the new device.
Note
If you want to remove a device from your
Rocketboost network you need to rejoin it to a
different hub device (this basically creates a 2nd
Rocketboost network).
The maximum number of audio streams that can be
sent simultaneously on the Rocketboost network is
five (stereo CD quality).

Installing batteries in the remote control

Cautions
• If the remote control doesn't work reliably, try
replacing the batteries.
• Don't mix new and old batteries or different
types of batteries.
• If you intend not to use the remote control for a
long time, remove the batteries to prevent
damage from leakage or corrosion.
• Remove expired batteries as soon as possible to
prevent damage from leakage or corrosion.
To install the batteries:
1 Remove the cover.
Batteries (AA/R6)
2 Insert two AA batteries into the compartment
matching the polarity indicated.
3 Replace the cover.

Using the remote control

Use the remote control by pointing it towards the
receiver's remote sensor window. Objects between
the remote control and sensor window may
prevent proper operation.
Remote control sensor
14
Use the remote control within about 16 feet
(5 meters) of the receiver and within 30 degrees of
perpendicular to the front of the receiver.

Configuring speakers (Sp Config menu)

This section explains how to specify which speakers
are connected and defines their sizes.
For speakers with a cone diameter larger than 6.5
inches (16 cm), specify Large (full band). For those
with a smaller diameter, specify Small (default
crossover 120 Hz).
The crossover frequency can be changed in the
Crossover submenu.
See "Using on-screen setup menus" on page 20 for
information on accessing and using the menus.
Speaker(s)
Subwoofer
Front
Center and Surround
Setting the crossover frequency (Crossover Frequency
Receiver
submenu of Sp Config menu)
This setting is recommended for the speakers that
you specify as Small. To get the best bass
performance from your speaker system, you need
to set the crossover frequency according to the size
and frequency response of your speakers. Options
Approx. 16 ft. (5 m) include 40Hz, 50Hz, 60Hz, 70Hz, 80Hz, 90Hz,
100Hz, 120Hz, 150Hz, and 200Hz.
Use the diameter of the smallest speaker in your
system when choosing the crossover frequency.
www.insigniaproducts.com
Insignia NS-AV511 Surround Sound Receiver
Cautions
• Do not expose the remote control to shock. In
addition, do not expose the remote control to
liquids, and do not place in an area with high
humidity.
• Do not place the remote control under direct
sunlight. The heat may cause deformation of
the remote control.
• The remote control may not work properly if the
remote sensor window of the receiver is under
direct sunlight or strong lighting. In such a case,
change the angle of the lighting or receiver, or
operate the remote control closer to the remote
sensor window.
Note
Speaker Configuration, Crossover Frequency, and
Double Bass settings are disabled while headphones
are connected, or when Audio TV OUT is set to On.
Configuration
Yes–if a subwoofer is connected.
No–If no subwoofer is connected.
Small–If speaker cone is 6.5 inches (16 cm) or less in
diameter.
Large–If speaker cone is larger than 6.5 inches (16 cm)
in diameter.
Note: If the Subwoofer setting is No, the default setting
for this is Large and cannot be changed.
Small–If speaker cone is 6.5 inches (16 cm) or less in
diameter.
Large–If speaker cone is larger than 6.5 inches (16 cm)
in diameter.
None–If no center speaker is connected.
Note: If the Front setting is Small, the Large option
cannot be selected.