Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kistler M2836A Series
Summary of Contents for Kistler M2836A Series
- Page 1 Instruction Manual Angular Rate Sensor Type M2836A… M2836A_002-509e-09.11...
- Page 2 Instruction Manual Angular Rate Sensor Type M2836A... M2836A_002-509e-09.11...
- Page 4 Information in this document is subject to change without notice. Kistler reserves the right to change or improve its products and make changes in the content without obligation to notify any person or organization of such changes or improvements.
-
Page 5: Table Of Contents
Characteristics ..........................5 Mechanical Fixing ....................... 5 Power Supply of the Sensor ....................6 ® 3.2.1 Using with Kistler MINIDAU ................6 3.2.2 Using with a Measuring System without Bipolar Power Supply ......7 Maximum Measuring Range ....................8 Temperature Compensation of the Sensor ................8 3.4.1... -
Page 6: Introduction
It will help you with the installation, maintenance, and use of this product. To the extent permitted by law Kistler does not accept any liability if this instruction manual is not followed or products other than those listed under Accessories are used. -
Page 7: Subject
Do not discard old electronic instruments in municipal trash. For disposal at end of life, please return this product to an authorized local electronic waste disposal service or contact the nearest Kistler Instrument sales office for return instruc- tions. Page 4... -
Page 8: Characteristics
Characteristics Characteristics Mechanical Fixing The triaxial angular rate sensor weighs approx. 200 grams (with cable). Thus, the mechanical fixing must be done carefully. The bottom plate of Type M2836A... is supplied with three fixing points for M5 screws: Fig. 1: Sketch of the bottom plate As shown in the drawing, one fixing point is open side- wards. -
Page 9: Power Supply Of The Sensor
41 mA (typical) per channel and axis. ® 3.2.1 Using with Kistler MINIDAU Type M2836A... can be directly connected to a Kistler ® MINIDAU The following instructions have to be followed, though: The current consumption of Type M2836A... lies in ƒ... -
Page 10: Using With A Measuring System Without Bipolar Power Supply
Type M2836A... cannot be directly connected to measuring systems and amplifiers whose power supply are 0 V and 10 V potential. Kistler’s APS monitors G2 and G3 and other measurement amplifiers on the market are in this group. To use the angular rate sensors Type M2836A... and Type M2816A…... -
Page 11: Maximum Measuring Range
Angular Rate Sensor Type M2836A... Maximum Measuring Range Type M2836A... has a maximum measuring range of 1 500°/s at a signal voltage of 2 V. It is possible to exceed the measuring range up to 2,2 V. This means however, the values on linearity and accuracy of the system that are veri- fied in the data sheet cannot be guaranteed for measuring range values that are higher than the specified value. -
Page 12: Sensor For Measuring The Translative Acceleration
Characteristics Sensor for Measuring the Translative Acceleration Type M2836A... can optionally be instrumented with an ad- ditional triaxial miniature accelerometer Type M312A…This accelerometer is a piezoresistive sensor. Because of its small height it can be mounted into the housing of Type M2836A... -
Page 13: Pin Assignment Of The Sensor
Angular Rate Sensor Type M2836A... Pin Assignment of the Sensor Fig. 5: Pin assignment, sample: 1B Lemo assignment A (Type M2836A... or Type M2816A…) Page 10 M2836A_002-509e-09.11... -
Page 14: Output Os1 Aps Test
Output OS1 APS Test Output OS1 APS Test 4036 IDNR: 4036 IDMN: Uref Rin+ ϑ EX– 15126 Rsh: Ω SE– Rin+: Ω Rin–: Ω SIG+ 5,02 Uref: Rin– NUSI: 0,122 mV/V SIG– 15,208 KELP: mV/V -15,368 KELM: mV/V ΜΩ ISOW: Auto: Baud Storage module...
Need help?
Do you have a question about the M2836A Series and is the answer not in the manual?
Questions and answers