Related Manuals for Lincoln Electric BesterMig 215-S
Summary of Contents for Lincoln Electric BesterMig 215-S
- Page 1 IM3205 05/2024 REV01 BesterMig 215-S OPERATOR’S MANUAL ENGLISH Lincoln Electric Bester Sp. z o.o. ul. Jana III Sobieskiego 19A, 58-260 Bielawa, Poland www.lincolnelectric.eu...
-
Page 2: Table Of Contents
12/05 THANK YOU! For choosing the QUALITY of the Lincoln Electric products. Please check packaging and equipment for damage. Claims for material damaged in shipment must be notified immediately to the dealer. For ease of use, please enter your product identification data in the table below. Model Name, Code & Serial Number can be found on the machine rating plate. -
Page 3: Technical Specifications
Frequency BesterMig 215-S 230+15% /-10%, 1-phase 50/60Hz Input Power at Rated Cycle Input Amperes I 1max BesterMig 215-S 10,5 kVA @ 10% Duty Cycle (40°C) 46 A 0,65 RATED OUTPUT Duty Cycle 40°C Open Circuit Process (based on a 10 min. - Page 4 WARNING While welding above 160A, You need to change overcurrent protection for a 20A - 25A type D and change for a proper input plug (or connect directly to a power network) Example: English English...
-
Page 5: Eco Design Information
Efficiency and idle power consumption: Efficiency when max power consumption Index Name Equivalent model / Idle power consumption B18266-1 BesterMig 215-S 81% / 25W No equivalent model Idle state occurs under the condition specified in below table IDLE STATE Condition Presence... - Page 6 Typical gas usage for MIG/MAG equipment: DC electrode positive Wire Wire Feeding Gas flow Material type diameter Shielding Gas Current Voltage [m/min] [l/min] [mm] Carbon, low 0,9 ÷ 1,1 95 ÷ 200 18 ÷ 22 3,5 – 6,5 Ar 75%, CO alloy steel Aluminium 0,8 ÷...
-
Page 7: Electromagnetic Compatibility (Emc)
Lincoln Electric. Before installing the machine, the operator must check the work area for any devices that may malfunction because of electromagnetic disturbances. -
Page 8: Safety
Failure to follow the instructions in this manual could cause serious personal injury, loss of life, or damage to this equipment. Read and understand the following explanations of the warning symbols. Lincoln Electric is not responsible for damages caused by improper installation, improper care or abnormal operation. - Page 9 ARC RAYS CAN BURN: Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing. Use suitable clothing made from durable flame- resistant material to protect you skin and that of your helpers. Protect other nearby personnel with suitable, non-flammable screening and warn them not to watch the arc nor expose themselves to the arc.
-
Page 10: Introduction
Introduction The welding machines BesterMig 215-S enables welding: Recommended equipment, which can be bought by user, was mentioned in the chapter "Accessories". GMAW (MIG/MAG) FCAW-SS (Self-shielded wire) SMAW (MMA) GTAW (Lift TIG). The complete package BesterMig 215-S contains: ... - Page 11 Controls and Operational Features Figure 2 6. Gas Connector: Connection for gas line. Figure 1 7. Power Switch ON/OFF (I/O): Controls the input power 1. EURO Socket: For connecting a welding gun (for to the machine. Be sure the power source is GMAW / FCAW processes).
- Page 12 User Interface Figure 3 9. Spooled Wire (for GMAW / FCAW): Not supplied as standard. 10. Wire Spool Holder: Maximum 15kg spools. Maximum 300mm diameter spools. Holder allows mounting Figure 4 plastic, steel and fiber spools onto 51 mm spindle. Note: Plastic Brake Nut has a Left-hand thread.
- Page 13 17. Welding Process Selection Button: Allow to choose 21. Left Control: Click to select the Ampere /Wire feed the welding process: speed / Inductance/ Material Thickness and turn to set the value of chosen parameter. Sets the value Process Symbol Description shown on the left display.
- Page 14 Welding GMAW, FCAW-SS Process Welding SMAW (MMA) Process BesterMig 215-S can be used to welding GMAW and BesterMig 215-S include the electrode holder with lead FCAW-SS process. necessary for SMAW welding. Preparation the Machine for Welding Procedure of begin welding of SMAW process: ...
- Page 15 Welding GMAW Process in synergic mode In synergic mode, the welding load voltage is not set by user. The correct welding load voltage will set by the machine’s software. The optimum output welding voltage is automatically set by the machine when changing the wire feed speed m/min or the output current value in A, depending on the selected workpoint.
- Page 16 The installation and connection Loading the Electrode Wire Depending on the type of wire spool it can be installed on the wire spool support without adapter or installed with use applicable adapter that must be purchased separately (see "Accessories" chapter). WARNING Turn the input power OFF at the welding power source before installation or changing a wire spool.
- Page 17 Proper adjustment of pressure arm BesterMig 215-S is equipped with drive roll V0.8/V1.0 gives the best welding performance. for steel wire. For others wire sizes, is available the proper drive rolls kit (see "Accessories" chapter) and...
- Page 18 Technical Service Center or Lincoln Electric. Repairs connector. and modifications performed by unauthorized service or personnel will cause, that the manufacturer’s warranty...
- Page 19 We respond to our customers based on the best information in our possession at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such information or advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customer’s particular purpose,...
- Page 20 Troubleshooting Problem Possible Cause Recommended Course of Action Input voltage is too high (≥15%) Switch off power source; check the main or Input voltage is too low supply. Restart welder when power (≤15%) recovers to normal state Yellow Thermal ...
-
Page 21: Weee
12/05 Part List reading instructions Do not use this part list for a machine if its code number is not listed. Contact the Lincoln Electric Service Department for any code number not listed. Use the illustration of assembly page and the table below to determine where the part is located for your particular code machine. -
Page 22: Accessories
Accessories OPTIONS & ACCESSORIES W10430-15-3M LGS3 150 MIG GUN, GAS COOLED - 3m. W10430-15-4M LGS3 150 MIG GUN, GAS COOLED - 4m W000010786 GAS NOZZLE CONICAL Ø12MM. W000010820 CONTACT TIP M6x25MM ECU 0.6MM W000010821 CONTACT TIP M6x25MM ECU 0.8mm WP10440-09 CONTACT TIP M6x25MM ECU 0.9mm W000010822 CONTACT TIP M6x25MM ECU 1.0mm... -
Page 23: Dimension Diagram
Dimension Diagram 03/24 English English...
Need help?
Do you have a question about the BesterMig 215-S and is the answer not in the manual?
Questions and answers