TMG -TSB48 Product Manual
  1. Manuals
  2. Brands
  3. TMG Manuals
  4. Tractor Accessories
  5. TMG-TSB48
  6. Product manual

TMG -TSB48 Product Manual

48" 3-point tractor stone burier
Hide thumbs Also See for TMG-TSB48:

Advertisement

Table of Contents

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TMG-TSB48 and is the answer not in the manual?

Questions and answers

Related Manuals for TMG TMG-TSB48

Summary of Contents for TMG TMG-TSB48

  • Page 2 SAFETY INSTRUCTIONS .............................. 3 OPERATING SAFETY ..............................4 PARTS DESCRIPTION AND FUNCTION ........................8 PRODUCTS SPECIFICATIONS .............................10 UNPACKING & ASSEMBLY ..............................11 CONNECTING TRACTOR ..............................19 CHECK BEFORE OPERATING ..............................23 LUBRICATION POINTS SUMMARY ........................... 24 OPERATING ESSENTIALS ............................25 OPERATION FINISH..............................

  • Page 3: Warning Decals

    Before operating the ROTARY TILLER read the following safety instructions. Failure to comply with these warnings may result in serious injury or death. WARNING DECALS Read and understand the operator manual completely before operating your rotary tiller. Keep hand, feet, hair and clothing away from all moving parts.
  • Page 4 Failure to comply with these warnings may result in serious injury or death ! Read and understand the operator manual before operating, servicing, adjusting, repairing or removing. Failure to understand warning or caution Don’ t operate especially for you don’ t know how completely may result in injury before operation.

  • Page 5: Working Conditions

    Check the surroundings before operation Observe and apply carefully the instructions for adjusting the height of the machine from the ground. ● If there are grass or weeds, it is advisable to clean the ground before moving on withthe Stone burier, in ●...
  • Page 6 Keep others away from machine and tractor Ensure that the rotary hoe is connected to when it is running or operating. the tractor by three- point linkage. Carry out tractor mounting operation on a Ensure that the tractor is in neutral when it is flat or hard ground.
  • Page 7 Stay away from the machine during operation, or you will be injured. Operate abide the specified speed, or the PTO will be damaged and people will be injured. Do not carry people and luggage on the working machine. 。 Shift down before into the ramps. High- speed moving on the ramps will slip. Concentrate during operation.
  • Page 8 www.tmgindustrial.com 7/35 Toll Free:1-877-761-2819...
  • Page 9 5. Adjusting tie rod 1. Three-Point linkage To change the tilt angle of the rear roller. Connect the rotary tiller with tractor 6. Shaft end 2. Gearbox Transmit power from side drive to the rotor. Change the output speed of the tractor and transmit 7.
  • Page 10 5 in）, logs and/ or any obstacle that could damage the machine during the use. The working speed of the machine should always be at a slow walking pace (approx.1 to 3 mph) depending on the working conditions TMG-TSB48 Model No Working width 48”...
  • Page 11 1. After unpacking, check the following components www.tmgindustrial.com 10/35 Toll Free:1-877-761-2819...
  • Page 12 Host Hexagon bolts M12*85 Extend the lower hanging Weldment ( left) Hexagon bolts M12*35 Extend the lower hanging weldment ( right) Hexagon bolts M12*60 Left suspension plate weldment Hexagon bolts M12*30 Right suspension plate weldment Hexagon bolts M12*45 Suspension rear connecting plate Lock nut M12 Drive shaft placement plate Flat washer Ø12...
  • Page 13 2. Installation of the roller assembly 1 . First install the 2 outer spherical ball bearings with seats (E1) on the shaft of the mesh wheel welding part (E9), and then use bolts(E5), washers(E3) and lock nuts(E4) to fasten the spring pull plate (E2) and the left and right connecting arms ( E11, E12 ) of the mesh wheel according to the pattern shown in the figure below.
  • Page 14 2 . When the scraper welding parts installed ( E10 ) , it is necessary to place the welding parts of the left and right connecting arms (E11,E12) of the mesh wheel at the same height, then fasten them with bolts(E8), washer(E6), lock nut( E7 ) , and then install the tension spring( E17 ) according to the below figure.
  • Page 15 All bolts are locked in place without shaking. Once the assembly bolts are not fastened in place, there will be abnormal noises when the machine is working. Outer spherical ball bearing with seat Spring pull plate Flat washer Ø12 Lock nut Hexagon Bolts M12x45 Flat washer...
  • Page 16 1 . Install the assembled roller assembly to the mounting hole on the host and fasten it with fasteners ( C13 / C 5 / C 12 / C 11 ). 2. After adjusting the length of the adjusting rod( E16 ) so that it can be installed on the hood, use the R pin(E13 ) to fix it on the host shaft.
  • Page 17 4. Suspension and dust cover installation 1 . Install the suspension components as shown in the figure 2 . Hung the assembled components according to the hanging installation diagram on the hood, install the suspension components of bolt hole and the gearbox bracket( F1 8 ) on the hood welded parts installation hole alignment, then install the lower hitch- R( F23 ) and lower hitch- L( F24 ) , install and tighten the bolts, flat washers and lock nuts in turn, and finally insert the lower hanging pin and lock pin (F25 and F20).
  • Page 18 Paying attention to the different bolt lengths of the hanging weldment and the hanging assembly under tightening extension (F6 and F5), Do not reverse the direction of the lower bracket assembly. All bolts are locked in place without shaking. Once the assembly bolts are not fastened in place, there will be abnormal noises when the machine is working.

  • Page 19: Three-Point Linkage

    Be sure no people stand between the tractor and working machine during the tractor moving. Ⅰ and Ⅱ TMG-TSB48 2. Connection and adjustment a. Start the tractor engine, tractor and machine head lower link under suspension corresponds to the position of the pin, rewind, stop, stop the engine, put up parking stalls.
  • Page 20 d. Adjust angle, to obtain the most appropriate cutting angle, adjust the upon 3 - point linkage suspension to ensure the suitable cutting angle. www.tmgindustrial.com 19/35 Toll Free:1-877-761-2819...

  • Page 21: Pto Installation

    3. PTO installation If you use no plastic cover to protect the coupling, it is possible to be involved in the occurrence of injuries. Do not use no plastic casing coupling. If you use damaged couplings, injuries may occur entangled. Couplings if damaged, replace it immediately.
  • Page 22 3 . After connection, fixed the chain to prevent the plastic cover rotation 4 . Max rotation angle of coupling If the shaft beyond its maximum operating angle of rotation at work, there will be unexpected injury accident. Be sure to fix the tractor three- point suspension before use. 4.
  • Page 23 1 . Check before operating 1 . Check the various parts of the tractor Please check the parts according to the manual 2 . Check the connection site ( 1 ) Fix connection pin of three- point suspension ( 2 ) Check the stand foot retract 3.
  • Page 24 ● Fuel and smear with clean oil ● Release the original gearbox oil when refueling. ● Designated parts have been oiling, please confirm before use. Change the oil in gearbox after the new hoe put in use after 50 hours Make routine inspection per 50 hours SAE90 GL-5 Gearbox...
  • Page 25 Don' t touch blade when in operation, injuries may occur. In high- speed rotating operation, the stone will fly out, take close attention to yourself and the problem around. Exceed the PTO speed may cause injury accident, make sure to operate within the specified speed. ...
  • Page 26 1. . Seiri and check after operating ( 1 ) Should organize and clean the rotary machine after the operation of rotary machines, remove the grass clippings, dirt during the job. ( 2 ) After using a rotary tiller should be careful to check some of the parts can be damaged, if parts need to be replaced, should also pay attention to cut off all the power, turn off the tractor firstly.
  • Page 27 1. Loose blade bolt 2 . Loose cutter bolts Tighten the bolts 3 . Incorrect oil Change Oil 4. Gear, bearing damage Replace damaged Parts 5 . Overload or soil hardness Readjust tillage depth is high Adjusting plate position was Coordinate well the adjusting plate position not coordinated well 1.

  • Page 28: Main Frame Assembly

    1. Main-frame assembly Hood assembly Roller assembly Slide drive assembly Suspension assembly End cover assembly Gearbox mounting assembly Blade axle assembly www.tmgindustrial.com 27/35 Toll Free:1-877-761-2819...

  • Page 29: Hood Assembly

    2. Hood assembly Shock- absorbing block Rear baffle shaft Split pin 4x20 Flat teeth Full- thread hexagon bolts The rubber pad (I) M10x30 Flat teeth pressing plate ( II) Hood panel The rubber pad Front baffle plate Plain washer Ø 1 0 Flat teeth bracket Spring washer Ø...
  • Page 30 3. Slide drive assembly www.tmgindustrial.com 29/35 Toll Free:1-877-761-2819...
  • Page 31 Drive shaft bearing seat Hexagon nuts M12 Front connecting plate Large plain washer Ø8 Full- thread hexagon bolts M10 × 40 Oil seal sleeve Large chain wheel Full- thread hexagon bolts M12 × 70 Small chain wheel Chain case Right side plate of blade axle Roller chain 1×42 Rear connecting bracket- R Fiber seal...
  • Page 32 4. End cover assembly Front connecting plate Retaining rings for bor P72 End cap Large plain washer Ø 1 0 Lower support plate Full- thread hexagon bolts M1 0 × 4 0 Full- thread hexagon bolts M1 0 × 3 5 Plain washer Ø...
  • Page 33 5. Blade axle assembly Spring washer Ø 1 2 Blade axle Blade- R Blade- L Full- thread hexagon bolts M1 2 × 3 5 Locknut M12 www.tmgindustrial.com 32/35 Toll Free:1-877-761-2819...

  • Page 34: Roller Assembly

    6. Roller assembly Outer spherical ball bearing with seat Mud shield Spring pull plate Connecting arm- L Connecting arm- R Plain washer Ø 12 Locknut M1 2 R Pin Ø4 Full- thread hexagon bolts M1 2 × 4 5 Full- thread hexagon bolts M8 × 5 0 Hexagon nuts M8 Plain washer Ø...

  • Page 35: Suspension Assembly

    7. Suspension assembly Full- thread hexagon bolts M8 × 2 5 U- bolt Rear connecting plate PTO Retaining plate Upper suspension spacer Left suspension plate Right suspension plate Plain washer Ø 12 Full- thread hexagon bolts M1 2 × 3 5 Gearbox bracket Full- thread hexagon bolts M1 2 ×...
  • Page 36 8. Gearbox mounting assembly The protective shield ( I) Transmission shaft The protective shield ( II) Plain washer Ø 12 Spring washer Ø 1 2 The protective shield ( III) Full- thread hexagon bolts M12 × 25 Gear box www.tmgindustrial.com 35/35 Toll Free:1-877-761-2819...

Table of Contents