Related Manuals for Buyers Snowdogg HDII Series
Summary of Contents for Buyers Snowdogg HDII Series
- Page 1 9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • snowdoggplows.com PATENTS PENDING 3036332_A...
-
Page 2: Table Of Contents
This manual is for the professional installation of WARNING snowdogg HDII/EXII, TEII and VXFII snowplows. When using on a vehicle with air bags, DO NOT tamper Review all instructions prior to installation. Installation with, disable or remove any components related to the related failures are not covered by warranty. -
Page 3: Moldboard/Lift Frame Assembly - Hdii/Exii
HDII/EXII Moldboard/Lift Frame Assembly Fig. 1 Bill of Materials LIFT POINTS ITEM QTY. PART NO. DESCRIPTION 16011002 HDII/EXII LIFT FRAME ASSEMBLY 16111634 Upper Lift Frame 16160700 Light Kit 16160710 LIGHT, DS 16160720 Light, DS Fig. 2 16101106 Lift Frame Hardware Kit –... -
Page 4: Moldboard/Lift Frame Assembly - Teii
TEII Moldboard/Lift Frame Assembly Fig. 3 LIFT POINTS Bill of Materials ITEM QTY. PART NO. DESCRIPTION 16012002 TEII Lift Frame Assembly Fig. 4 16111634 Upper Lift Frame 16160700 Light Kit 16160710 Light, DS 16160720 Light, DS 1. Attach the Moldboard to the A-Frame using the 16101106 Lift Frame Hardware Kit Pivot Bolt kit (7) and Angle Stop Bolt kit (8) -
Page 5: Moldboard/Lift Frame Assembly - Vxfii
VXFII Moldboard/Lift Frame Assembly Fig. 5 Bill of Materials 4.75 Fig. 6 LIFT FRAME ITEM QTY. PART NO. DESCRIPTION 4.00 SHIPPING PALLET 16013002 VXFII Lift Frame Assembly 2. Attach both angle cylinders on the LIFT FRAME to 16111634 Upper Lift Frame 16160700 Light Kit the MOLDBOARD as shown using the 7/8”... -
Page 6: Upper Lift Frame Assembly
Prop Foot Deployment For shipping the prop feet are in the transport position and the lift frame/Aframe are in stacking position. For mounting, the prop feet will need to be rotated to the deployed position so that the plow can be mounted. This step requires two people or a winch to rotate the lift frame. -
Page 7: Vehicle Side Installation
1. For ease of assembly, remove the two front HPU covers by pulling out the retainer pins and set aside. The retainer pins are captive in the plastic covers – do not remove. 2. The UPPER LIFT FRAME (2) fits into the LIFT FRAME (1) as shown in Figure 5. Insert it and seat securely. 3. - Page 8 Vehicle Side Electrical Installation The SnowDogg plow has separate harnesses for Hydraulic and Lighting for ease of installation and trouble- shooting. Either harness can be omitted without affecting the functionality of the other system. CAUTION Keep all connectors greased with dielectric grease on a regular basis to minimize corrosion & potential damage or wear to the pins.
- Page 9 1. Route the CONTROL HARNESS through the truck grill, by the battery, and through the firewall. If no available opening exists, a ø7/8" hole will need to drilled through the firewall. Check your truck Owner’s Manual for details on where this can safely done. If the hole is drilled it is critical that a grommet be used to prevent damage to the wire harness.
- Page 10 Light Harness Installation The light harness is split into a RELAY MODULE and GRILL HARNESS to allow for easy installation. Connectors have been designed in such a way to prevent installation errors – but be sure to read all instructions. 1.
- Page 11 Switched Ground 16160102 RELAY HARNESS "B" LONG LEAD TO HEADLIGHT ADAPTER TURN SIGNAL CONNECTORS "A" SHORT LEAD TO HEADLIGHT ADAPTER BLACK WIRE TO GROUND 16160104 LIGHT/GRILL HARNESS ORANGE WIRE TO GRILL HARNESS WHITE/BLACK TO CONTROL HARNESS WHITE/BLACK TO ORANGE • Cut open the loom on the GRILL HARNESS near the 8-pin connector to locate the WHITE/BLACK wire. This wire has male and female connectors in line.
- Page 12 Plow Mounting And Checkout Your fully assembled plow is now ready to mount to the vehicle that you have prepared. Mount the plow using the instructions as shown. MOUNTED PLOW DISMOUNTED PLOW CHAIN LIFT ADJUSTABLE FOOT PROP STAND 10.5 - 11.0 PROP STAND PIN HEIGHT ADJUSTABLE...
-
Page 13: Light Aiming
Verify that all plow lights work properly • LOW BEAM • HIGH BEAM • FLASH TO PASS • TURN SIGNALS • PARKING LIGHTS Mount and Dismount the plow several times to confirm that all components work as intended. If any portion of the truck bumper or air dam interferes with mounting, it may need to be removed or the pushbar lowered. -
Page 14: General Information
STORAGE 1. Before disconnection the plow from your vehicle, fully compress the lift cylinder 2. Disconnect the plow from your vehicle 3. Coat all electrical connection points with dielectric grease 4. Repair/touch up any chipped paint or rusted areas 5. Apply a coat of oil or grease to all exposed chrome (on angle and lift cylinders) 6. - Page 15 …damage to vehicle and/or frame of vehicle resulting from plow attachment. WARRANTY PROCEDURE If any part is proven to be defective within that warranty period, Buyers Products will, at its sole discretion, repair or replace said part at its expense FOB Cleveland, OH. Labor will be credited to authorized dealers as determined by published rate charts.
- Page 16 3036332_A...