Page 1
Circular duct fan Installation and Operating Instructions Document in original language | · 003 Get In Touch Our Address Call: 0845 6880112 Puravent, Adremit Limited, Unit 5a, Commercial Yard, Settle, North Yorkshire, BD24 9RH Email: info@adremit.co.uk...
Contents General information .........1 Warning symbols ........1 1.1.1 Instruction symbols.....1 Important safety information ......1 Personnel ..........1 Personal protective equipment....2 5 rules of electrical safety ......2 Warranty ............2 Delivery, transport, storage .......3 Description ............4 Intended use .........4 Incorrect use ........4 Technical data ........4 Dimensions ...........4 Name plate and type key ........5 Accessories............6...
Page 4
Get In Touch Our Address Call: 0845 6880112 Puravent, Adremit Limited, Unit 5a, Commercial Yard, Settle, North Yorkshire, BD24 9RH Email: info@adremit.co.uk...
General information | General information Warning symbols Danger Caution Hazard with a low risk Direct hazard Failure to comply with this warning may lead to Failure to comply with this warning will lead moderate injuries. directly to death or to serious injury. Important Warning Hazard with risk of damage to objects...
Further prerequisites are a completed maintenance plan with no gaps and a commissioning re- port. Systemair will require these in the case of a warranty claim. The commissioning report is a component of this document. The maintenance plan must be created by the operator, see section Maintenance.
Delivery, transport, storage | Delivery, transport, storage Safety information Warning: Risk from rotating fan blades ♦ Prevent access by unauthorised persons by safety personnel or access protection. Warning: Suspended loads ♦ Do not walk under suspended loads. ♦ Make sure that there is nobody under a suspended load. Delivery Each fan leaves our plant in an electrically and mechanically proper condition.
| Description Description Intended use • The fans are intended for installation in ventilation systems. They can be installed both in duct systems and also with free suction via a suction-side contact protection grille. Free discharge via a contact protection grille is also possible. •...
Name plate and type key | Name plate and type key Type designation Insulation class Voltage/current/frequency Article number/production number/ manufacturing date Input power Certifications Enclosure class/fan impeller speed/weight Table 2 Type key Normal motor version Large motor version Motor type 2 poled/voltage controllable/1 phased Size Fan type...
Electrical connection | Important Damage to the bearings or other parts of the fan can occur. ♦ Do not place a duct bend directly before or after the fan! ♦ Ensure a smooth and constant air flow to the device. min.
| Commissioning Wiring diagram Color Function/pin assignment Black Power supply 230 V AC, 50...60 Hz Blue Neutral conductor Green/Yellow Protective conductor Protecting the motor Important Damage to motor due to overcurrent, overload or short circiut. ♦ Lead-out temperature monitors must be integrated in the control circuit in such a way that, if a fault occurs, the motor cannot switch on again automatically after it has cooled down.
Problem Possible causes Remedy Soiling on the impeller Clean carefully Material decomposition on the impeller due Contact Systemair to aggressive material conveyed. Fan does not run Impeller rotates in wrong direction. Contact Systemair smoothly Deformation of impeller due to excessive Ensure that the temperature does not exceed temperature.
Spare parts ♦ Use original spare parts from Systemair only. ♦ When ordering spare parts, please specify the serial number of the fan. This can be found on the name plate. | 003 Get In Touch...
Cleaning | Cleaning Safety information ♦ Observe 2 Important safety information, page 1 Procedure Keeping the fan clean extends its service life. • Install a filter monitor. • Change the filters of the ventilation system. • Do not use steel brushes or sharp-edged objects. •...
| Commissioning Report Commissioning Report Warranty claims can only be made if commissioning work is carried out correctly and written evidence thereof is provided. Description: Article no.: Manufacturing order no.: Installer Company: Contact person: Company address: Tel. no.: Email: Operator (Place of installation) Company: Contact person: Company address:...
Page 17
Commissioning Report | Fan impeller speed [rpm]: Current L1 [A]*: Current L2 [A]: “Air volume”, “Differential pressure” not necessary for Jet fans Air volume [m3/s]: Current L3 [A]: Differential pressure [Pa]*: *For single-phase fans, fill in line “Current L1 [A]” *Δ- Pressure between suction-side and discharge of the fan If an air flow measurement is not possible, this value can be calculated using the following formula: Flow speed [m/s]...
Page 18
Systemair GmbH Seehöfer Str. 45 97944 Boxberg Germany Tel.: +49 (0)7930/9272-0 Fax: +49 (0)7930/9273-92 info@systemair.de www.systemair.de Get In Touch Our Address Call: 0845 6880112 Puravent, Adremit Limited, Unit 5a, Commercial Yard, Settle, North Yorkshire, BD24 9RH Email: info@adremit.co.uk...
Need help?
Do you have a question about the RVK and is the answer not in the manual?
Questions and answers