Table of Contents
Related Manuals for Belleze 050-HA-50118
Summary of Contents for Belleze 050-HA-50118
- Page 1 18" Insert Fireplace Heater FOLLOW US: CONTACT INFO: ITEM NO. 050-HA-50118 The instruction booklet contains IMPORTANT support@belleze.com @bellezefurniture safety information. Please read it in full and 1-800-682-6376 keep it for future reference. www.belleze.com...
-
Page 2: Technical Specification
Scan this QR Code to view our online tutorial Estimated time for assembly: 20 mins TECHNICAL SPECIFICATION Model Number 050-HA-50118 Dimensions (W x D x H) 19.17” x 5.08” x 17.52” Net Weight 9.48 lb Gross Weight 13 lb Power Rating... - Page 3 When using electrical appliances, basic safety precaution should always be followed including the following: READ ALL INSTRUCTION BEFORE USE 1. Read all instructions before using this heater. 2. Do not use this heater outdoors. 3. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations.
- Page 4 ⚠ WARNING There is no user serviceable parts inside the fireplace / heater. If the unit appears to be malfunction, turn off the unit and unplug from the wall outlet immediately, and then contact the customer service. ⚠ WARNING The heater is hot when in use. To avoid burns, do not touch hot surfaces. Keep combustible materials such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 ft (0.9 m) away from the front of the heater, and away from the side or rear of the heater.
- Page 5 Model No.: 050-HA-50118 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 6 Assemble the furniture on an empty carton, carpet, or rug to prevent scratches or damage. For safety, please keep pets and children away from the assembly area. Ensure the product is fully assembled before use. If you are missing any hardware or products, do not use it until you have restored the missing parts.
-
Page 7: Package Contents
PACKAGE CONTENTS CODE DESCRIPTION Heater Remote Control EVA Cushion Gasket Screws v.05032022... - Page 8 Attach EVA cushion gasket to the frame of the heater. ⚠ CAUTION The heater has a glass front panel. Careful when handling glass to prevent injury or damage. Set the unit from the back of the fireplace mantel and center it in the opening. Check the alignment and attach the unit to the mantel by inserting screws through the drilled holes on the mantel.
-
Page 9: User Instruction
USER INSTRUCTION Before use • Check that the air intake and exhaust is not covered or obstructed in anyway. • Keep combustible objects at least 3 ft (0.9 m) away from the unit. • Plug the unit to a grounded power socket Grounding •... -
Page 10: Caution / Warning
USER INSTRUCTION (CONTROL PANEL) Flame Control Power Button Display Function Indicator Heater Control Timer Control Control Panel The control panel is located on the top right corner of the unit. Power ON / OFF Press the power button to turn on the unit. Press again to turn off the unit. NOTE: There is a thermostat limiter inside the unit. - Page 11 USER INSTRUCTION (CONTROL PANEL) Heater Control When the heater is turned on, press and hold the heater control button for 5 seconds to enter temperature adjustment mode. The LED indicator is red. In adjustment mode, the display will To switch from degree Fahrenheit to degree Celsius, press and hold the power button for 5 seconds when the heater is turned on.
- Page 12 USER INSTRUCTION (REMOTE CONTROL) Power Button Heater Control Flame Control Timer Control Heater Down Heater Up Remote Control The operation of the remote control buttons work the same as the button on the control panel. NOTE: The remote control cannot be used to switch between degree Fahrenheit and degree Celsius.
- Page 13 USER INSTRUCTION (REMOTE CONTROL) Install / Replace Battery The remote control is provided with 2 AAA batteries. 2. Insert 2 AAA betteries into the battery compartment and make sure to intall batteries in the correct polarity. 3. The negative end of the battery should be install against the spring inside the battery compartment.
- Page 14 FURNITURE CARE AND MAINTENANCE Thank you for your purchase. We want your item to last as long as possible. To ensure the product gives you years of longevity, please follow the recommendations in this care and maintenance guide. CLEANING • Always turn off and unplug the unit from the power outlet before cleaning.
-
Page 15: Troubleshooting
Use it closer to the unit / change battery / remove insulating plastic sheet. © All copyright of this document belongs to BELLEZE . This document may not be printed, translated, reproduced, or distributed in whole or in part without written permission from BELLEZE. -
Page 16: Warranty
WARRANTY BELLEZE products come with a 1-year warranty from the date of delivery. Register your product on our website to enjoy our limited lifetime warranty! AFTER-SALE SERVICE Encounter any difficulties or missing parts? Contact us at 1-800-682-6376 or email us at support@belleze.com We will send you replacement.
Need help?
Do you have a question about the 050-HA-50118 and is the answer not in the manual?
Questions and answers
Hello the flame stop working on fire place model 050-HA-50118
The flame is not working on the Belleze fireplace model 050-HA-50118 because the flame spindle may have fallen off from the spindle motor. To fix this, open the top and back panel to check and reattach the flame spindle if necessary.
This answer is automatically generated