Advertisement
Available languages
Available languages
C)ccasional care and maintenance of the unit and the software
are neecled to optimize the performance of your unit.
To clean the cabinet
Use a soft and dry cloth.
If the surfaces are extremely
dirty, use a soft cloth lightly
moistened with mild detergent solution.
Do not use strong
solvents, such as alcohol, benzine or thinner as these could
damage the finish of the unit.
To clean the tape heads
VVhen the tape heads are dirty;
- high frequency sound is not emitted
- the sound is not adequately high
- the sound is off-balance
- the tape cannot be erased
- the tape cannot be recorded on
After every 10 hours of use, clean the tape heads with a head
cleaning cassette.
Fiefer to the instructions of the cleaning cassette for details,
To demagnetize
the tape heads
l-he tape heads may become magnetized after long-term use.
This may narrow the output range of recorded tapes and increase
noise.
After every 20 to 30 hours of use, demagnetize the tape heads
with a separately sold demagnetizing cassette.
Fiefer to the instructions of the demagnetizing cassette for details.
Care of discs
* When a disc becomes dirty, wipe the disc from the center out
with a cleaning cloth,
* After playing a disc, store the disc in its case. Do not leave the
disc in places that are hot or humid.
Care of tapes
* Store tapes in their cases after use.
* Do not leave tapes near magnets, motors, television sets, or
any source of magnetism .This will downgrade the sound quality
and cause noise.
* Do not expose tapes to direct sunlight, or leave them in a car
parked in direct sunlight.
There is no sound.
~
Is the AC cord connected propf?rly?
Is there a bad connection? (+ Ipage 4)
z
There may be a short circuit in the speaker terminals.
+ Disconnect
the AC cord, then correct
the speaker
,
connections,
i
,W'lo
4
'""
o ,:,",
Was an incorrect function button pressed?
~:~ "' " Kg"
Sound is emitted
from one speaker
only.
~'~ ~:~:
::lj 6(I
Is the other speaker disconnected?
!!,?
,,,,,
An erroneous display or a malfunction
occurs.
~#
+ Reset the unit as stated below.
,,,?,.
i,,,
TUNER SECTION
There is constant,
wave-like
static.
Is the antenna connected properly? (+ page 5)
* Is the signal weak?
+ Connect an outdoor antenna.
The reception contains noise interferences
or the sound
is distorted.
Is the system picking up external noise or multipath distortion?
-+ Change the orientation of the antenna.
+ Move the unit away from ot~ler electrical appliances.
CASSETTE
DECK SECTION
The tape does not run,
Is deck 2 in pause mode? (+ paga 8)
The sound is off-balance
or not adequately
high.
Is the playback head dirty? (+ page 19)
Recording
is not possible.
Is the erasure prevention tab on the tape broken off? (+ page
12)
Is the recording head dirty? (+ page 19)
Erasure is not possible.
Is the erasure head dirty? (+ pagf? 19)
Is a metal tape being used?
High frequency sound is not emitted.
Is the recording/playback head dirty? (+ page 19)
CD PLAYER SECTION
The CD player does not play.
Is
the disc correctly placed? (+ page 10)
Is
the disc dirty? (+ page 19)
Is the lens affected by condensation?
+ Wait approximately one hour and try again.
To reset
If an unusual condition occurs in the display window or the
cassette decks, reset the unit as follows.
1
Press
POWER
to turn
off the power.
2 Press POWER to turn the power back on while pressing
CLEAR.
Everything
stored in memory after purchase is
canceled.
If the power cannot be turnec~ off in step 1 because of a
malfunction, reset by disconnecting the AC cord, and connect it
again. Then carry out step 2.
ENGLEN+
19
Advertisement
