Denon AVR-3311 Owner's Manual page 84

Setting items
Distance
(Continued)
• The speakers that can be selected differ depending on the "Amp Assign"
(vpage 79) and "Speaker Config." (vpage 79) settings.
• Default settings :
Front L / Front R / Center / Subwoofer / F.Height L / F.Height R / F.Wide L /
F.Wide R : 12.0 ft (3.6 m)
Surround L / Surround R / S.Back L / S.Back R : 10.0 ft (3.0 m)
• Set the difference in the distance between the speakers to less than 20
ft (6.0 m).
NOTE
Speakers set to "None" in "Speaker Config." (vpage 79) are not displayed.
Default : The "Distance" settings are returned to the default settings.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
When you select "Default" and press
prompt is displayed. Select either "Yes" or "No", and press
Channel Level Test Tone Start : Output test tone.
Set the volume of the test • Front L / F.Height L / Center / F.Height R / Front R / F.Wide R /
tone to be the same when it Surround R / S.Back R
is output from each speaker. Subwoofer : Select the speaker.
z When the "Speaker Config." – "S.Back" setting (vpage 80) is set to
"1spkr", "S.Back" is displayed.
• –12.0dB – +12.0dB (0.0dB) : Adjust the volume.
o
• When is pressed while the subwoofer volume is set to "–12 dB", the
"Subwoofer" setting switches to "OFF".
• When "Channel Level" is adjusted, the adjusted values are set for all the
surround modes. To adjust the channel level separately for the different
surround modes, use the operation see page 55.
NOTE
• Speakers set to "None" in the "Speaker Config." (vpage 79) settings
are not displayed.
• When a headphones jack is inserted in the PHONES jack of this unit, the
"Channel Level" is not displayed.
Default : The "Channel Level" settings are returned to the default settings.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
When you select "Default" and press
prompt is displayed. Select either "Yes" or "No", and press
Remote control operation
buttons
Setting details
ENTER
, the "Default Setting?"
ENTER
.
z z
/ S.Back L / Surround L / F.Wide L /
ENTER
, the "Default Setting?"
ENTER
.
Move the cursor
(Up/Down/Left/Right)
Setting items
Crossover Frequency Crossover : Set the crossover frequency.
Set the maximum frequency • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
of the bass signal output 250Hz
from each channel to
Advanced : Specify crossover frequency for each speaker.
the subwoofer. Set the
• Front / Center / Surround / S.Back / F.Height / F.Wide : Select the
Crossover Frequency to
speaker.
suit the bass reproduction
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
capability of the speaker
250Hz : Set the crossover frequency.
being used.
• "Crossover Frequency" can be set when the "Bass Setting" –
"Subwoofer Mode" (vpage 80) setting is "LFE+Main", or when you
have a speaker that is set to "Small".
• Always set the crossover frequency to "80Hz". When using small
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
• For speakers set to "Small", sound below the crossover frequency
is cut from the sound output. The cut bass sound is output from the
subwoofer or front speakers.
• The speakers that can be set when "Advanced" is selected differ
depending on to the "Subwoofer Mode" setting (vpage 80).
• When "LFE" is selected, speakers set to "Small" at "Speaker Config."
can be set. If the speakers are set to "Large", "Full Band" is displayed
and the setting cannot be made.
• If set to "LFE+Main", this setting can be made regardless of the
speaker size.
Front Speaker Setup 2CH DIRECT/STEREO : The front speakers used in the direct, stereo and
Set the front speakers to pure direct play modes (2 channel) are set in advance.
use for every surround • A : Front speaker A is used.
mode. • B : Front speaker B is used.
• A+B : Both front speakers A and B are used.
NOTE
MULTI CH : The front speakers used in modes other than the direct,
This can be set when "Amp
stereo and pure direct play modes (2 channel) are set in advance.
Assign" is set to "Front B"
• A : Front speaker A is used.
(vpage 79).
• B : Front speaker B is used.
• A+B : Both front speakers A and B are used.
Confirm the setting
ENGLISH
Manual Setup
Setting details
81
Return to previous menu