Error Messages - Denon AVR-3311 Owner's Manual

ENGLISH

Error messages

An error message is displayed if Audyssey ® Auto Setup could not be completed due to speaker placement, the measurement environment, etc.
If this happens, check the relevant items, be sure to take the necessary measures, then perform Audyssey Auto Setup over again.
NOTE
Be sure to turn off the power before checking speaker connections.
Examples
$872 6(783
$8'<66(< $872 6(783
0XOW(4 ;7
&DXWLRQ
1R PLFURSKRQH RU 6SHDNHU
5HWU\
5(7851 &DQFHO
&KHFN FDXVH RI SUREOHP
$872 6(783
$8'<66(< $872 6(783 0XOW(4 ;7
&DXWLRQ
$PELHQW QRLVH LV WRR KLJK
RU /HYHO LV WRR ORZ
5HWU\
5(7851 &DQFHO
&KHFN FDXVH RI SUREOHP
$872 6(783
$8'<66(< $872 6(783 0XOW(4 ;7
&DX LRQ
)URQW 5 1RQH
5HWU\
5(7851 &DQFHO
&KHFN FDXVH RI SUREOHP
$872 6(783
$8'<66(< $872 6(783
0XOW(4 ;7
&DX LRQ
)URQW / 3KDVH
5HWU\
6NLS
5(7851 &DQFHO
&KHFN FDXVH RI SUREOHP
10
Remote control operation
buttons
Error details
• The connected setup microphone is broken,
or a device other than the supplied setup
microphone is connected.
• Not all speakers could be detected.
• The front L speaker was not properly
detected.
• There is too much noise in the room for
accurate measurements to be made.
• Speaker or subwoofer sound is too low for
accurate measurements to be made.
• The displayed speaker could not be detected. • Check the connections of the displayed
• The displayed is connected with the
polarities reversed.
Move the cursor
(Up/Down/Left/Right)
Measures
• Connect the included setup microphone to
the SETUP MIC jack of this unit.
• Check the speaker connections.
• Either turn off any device generating noise
or move it away.
• Perform again when the surroundings are
quieter.
• Check the speaker installation and the
direction in which the speakers are facing.
• Adjust the subwoofer's volume.
speaker.
• Check the polarities of the displayed
speaker.
• For some speakers, this error message may
be displayed even if the speaker is properly
connected. If you are sure the connection is
ui
correct, press to select "Skip", then
ENTER
press .
Confirm the setting
Parameter Check
This function enables you to check the measurement results and
equalizer characteristics after Audyssey Auto Setup.
1
8VH ui WR VHOHFW ³3DUDPHWHU &KHFN´ DQG WKHQ
SUHVV RU p 
ENTER
2
8VH ui WR VHOHFW WKH LWHP \RX ZDQW WR FKHFN WKHQ
p
SUHVV RU 
ENTER
Measurement results for each speaker are displayed.
$872 6(783
3$5$0(7(5 &+(&.
6SHDNHU &RQILJ &KHFN
'LVWDQFH &KHFN
&KDQQHO /HYHO &KHFN
&URVVRYHU &KHFN
(4 &KHFN
5HVWRUH
6KRZ VSHDNHU FRQILJXUDWLRQ UHVXOW
Check the speaker configuration.
Speaker Config. Check
Check the distance.
Distance Check
Check the channel level.
Channel Level Check
Check the crossover frequency.
Crossover Check
Check the equalizer.
EQ Check
ui
• If "EQ Check" is selected in step 2, press
curve ("Audyssey" or "Audyssey Flat") to be checked.
o p
Use to switch the display between the different speakers.
3
3UHVV 
RETURN
The confirmation screen reappears. Repeat steps 2.
Retrieving Audyssey Auto Setup settings
If you set "Restore" to "Yes", you can return to Audyssey Auto Setup
measurement result (value calculated at the start by MultEQ ® XT)
even when you have changed each setting manually.
Return to previous menu
to select equalizing