Page 1
Please refer to the MODIFICATION NOTICE. SERVICE MANUAL MODEL E1K E1C AVR-3311CI AVR-3311 AV SURROUND RECEIVER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail.
SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
Page 3
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacture CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
TECHNICAL SPECIFICATIONS s n Audio Section n HD Radio section (for E3) • Power amplifier –15 [FM](Note: μV at 75 Ω, 0 dBf = 1 x 10 Rated output : Receiving Range : Front : 125 W + 125 W (8 Ω, 20 Hz – 20 kHz with 0.05 % T.H.D.) [FM] 87.5 MHz – 107.9 MHz [AM]530 kHz – 1710 kHz 165 W + 165 W (6 Ω, 1 kHz with 0.7 % T.H.D.) Usable Sensitivity : Center : 125 W (8 Ω, 20 Hz – 20 kHz with 0.05 % T.H.D.) [FM]1.5 μV (14.8 dBf) [AM]20 μV 165 W (6 Ω, 1 kHz with 0.7 % T.H.D.) S/N (IHF-A) : Surround : 125 W + 125 W (8 Ω, 20 Hz – 20 kHz with 0.05 % T.H.D.) 165 W + 165 W (6 Ω, 1 kHz with 0.7 % T.H.D.) [FM]MONO 78 dB [AM] STEREO 68 dB...
Page 5
So make sure to memorize your setting for restoring after the initialization. Service Jigs When you repair the printing board, you can use the following JIG (Extension cable kit). Please order to Denon Official Service Distributor in your region if necessary. 8U-110084S : EXTENSION UNIT KIT : 1 Set...
Page 6
DISASSEMBLY s • Disassemble in order of the arrow of the figure of following flow. • In the case of the re-assembling, assemble it in order of the reverse of the following flow. • In the case of the re-assembling, observe "attention of assembling" it. • I f wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation. CABINET TOP FRONT PANEL ASSY HEAT SINK ASSY HDMI UNIT ASSY Refer to "DISASSEMBLY Refer to "DISASSEMBLY Refer to "DISASSEMBLY 1. FRONT PANEL ASSY" 2. HEAT SINK ASSY" 4. HDMI UNIT ASSY" and "EXPLODED VIEW"...
Page 7
About the photos used for descriptions in the DISASSEMBLY" section. • T he direction from which the photographs used herein were photographed is indicated at "Direction of photograph: ***" at the left of the respective photographs. • Refer to the table below for a description of the direction in which the photos were taken. • Photographs for which no direction is indicated were taken from above the product. The viewpoint of each photograph Direction of photograph: B (Photografy direction) Front side View from above Direction of photograph: C Direction of photograph: D Direction of photograph: A...
1. FRONT PANEL ASSY Proceeding : CABINET TOP FRONT PANEL ASSY (1) Remove the screws. View from bottom (2) Cut the wire clamp band, then disconnect the connector wires and FFC cable. Remove the screws. STYLE PIN : Loose CP100 STYLE PIN : Loose FFC cable N4201 FFC cable Please refer to "EXPLODED VIEW" for the disassembly method of each PCB included in FRONT PANEL ASSY.
Page 9
2. HEAT SINK ASSY Proceeding : CABINET TOP HEAT SINK ASSY (1) Remove the screws. View from bottom (2) Cut wire clamp band, then remove the screws. Disconnect the connector wires. Direction of Direction of photograph: C photograph: D CP100 STYLE PIN : Loose...
Page 10
(3) Remove the screws. Direction of photograph: A (4) C ut the wire clamp bands, then disconnect the connector wires and FFC cable. Remove the screws, SUPPORTER P.C. and the HDMI BRACKET. HEATSINK ASSY STYLE PIN : Loose CUSHION BRACKET SUPPORTER P.C. N4905 HDMI BRACKET FFC cable N4201 FFC cable (5) Disconnect the connector wires. CP401 CP402 STYLE PIN : Loose PCB 7CH AMP CP403 CP405 Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in HEAT SINK ASSY.
Page 11
3. PCB REG CNT/PCB REG Proceeding : CABINET TOP HEAT SINK ASSY PCB REG CNT/PCB REG (1) Remove the screws. PCB REG (2) Disconnect the connector wires and connector board. CP104 CP102 PCB REG CNT N2004 CP13A Direction of photograph: C Board to board PCB REG...
Page 12
4. HDMI UNIT ASSY Proceeding : CABINET TOP HDMI UNIT ASSY (1) Remove the screws, then remove the BACK PANEL and the HDMI BRACKET. Direction of photograph: A (2) Cut wire clamp band, then disconnect the connector wires and the FFC cables. Remove the screws and the SUPPORTER P.C.. Remove the PCB SIRIUS and the PCB RS232 from the PCB SIDE CNT(Board to board). STYLE PIN : Loose CUSHION BRACKET HDMI UNIT ASSY SUPPORTER P.C. PCB SIRIUS PCB 232C BACK PANEL N4201 FFC cable HDMI BRACKET...
Page 13
(3) C ut the wire clamp band, then disconnect the connector wires. Remove the screw. HDMI UNIT ASSY N4905 Direction of photograph: C CP13A N2004 (4) Remove the screws and disconnect the connector. CP401 CP402 CP403 STYLE PIN : Loose CP405 CP102 N4610 CP104...
Page 14
(5) Disconnect the connector wire, then remove the screws and the SUPPORTER P.C.. SUPPORTER P.C. CX102 (6) Remove the LICENCE LABEL, then remove the screws and SUPPORTER P.C.. Remove the HDMI UNIT ASSY from the main unit. SUPPORTER P.C. LICENCE LABEL View from bottom Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in HDMI UNIT ASSY. 5. TRANS MAIN Proceeding : CABINET TOP HDMI UNIT ASSY TRANS MAIN Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in TRANS MAIN.
Page 15
SPECIAL MODE Special mode setting button b Press the ON/STANDBY button to turn on while pressing both buttons A and B at the same time. Mode Button A Button B Contents Serial No. and firmware versions such as Main, Sub, DSP are Version display STATUS RETURN displayed in the FL manager. Errors are displayed when they (μcom/DSP Error Display) occur. (Refer to 16 page) Displaying the protection history Displaying the protection history mode STATUS MENU (Refer to 19 page) IInitialization mode Backup data initialization is carried out. STANDARD (Remove settings for Installer Setup.) SIMULATION (Remove settings for Installer Setup) Initialization mode CURSOR Backup data initialization is carried out. CURSOR UP (Includes settings for Installer Setup) DOWN (Includes settings for Installer Setup) DIRECT/ ---E2 model only--- Mode for switching tuner frequency step...
Page 16
1. µcom/DSP Version display mode 1.1. Operation specifications µcom/DSP version display mode: When started up, the version information is displayed. Starting up: With the "RETURN" and "STATUS" buttons pressed, press the "ON/STANDBY" button to turn the power on. Now, press the "STATUS" button to the display the 2nd item information on the FL Display. 1.2. Display Order Error information(Refer to 1.3. Error display) → q Model destination information → w Firmware Package Version → e Main µ-com/ROM version → r Main 1st Boot Loader → t Sub µ-com/Sub FBL → y DSP version → u Audio PLD → i OSD FPGA Config → o OSD Program → Q0 O SD font data → Q1 E thernet(DM860) 1st Boot Loader, Hardware ID → Q2 E thernet(DM860) 2nd Boot Loader, Rhapsody Flag → Q3 E thernet(DM860) IMAGE → Q4 E thernet(DM860)MAC ADDRESS information → Q5 H D RADIO SDK/HD RADIO BBP → Q6 i Pod Version → Q7 M ultEQ Pro APP(Displayed when Audyssey Pro is complete) → Q8 M ultEQ Pro ICL(Displayed when Audyssey Pro is complete...
Page 17
o OSD Program : Upper O S D P R G : Lower * * * * * * * * * * * * Q0 O SD font data : Upper O S D D A T : Lower * * * * * * * * * * * * Q1 E thernet(DM860) 1st Boot Loader, Hardware ID : Upper * E t h e r n e t...
Page 18
1.3. Error display See the following table for each "Error information" display and its contents (status). Display order is q , w , e , r , t . Condition State State q Sub-μcom NG No response from Sub-μcom S U B E R R O R w DIR NG No response from DIR D I R E R R O R When DSP boot, executing DSP reset makes no change to DSP1 FLAG0 D S P E R R O R...
Page 19
2. Errors checking mode (Displaying the protection history) 2.1. Operation specifications Error mode (Displaying the protection history): When started up, the error information is displayed. Starting up: ●All model commonness With the "STATUS" and "MENU" buttons pressed, press the "ON/STANDBY" button to turn the power on. The error (protection history display) mode is set. Now, press the "STATUS" button to turn on the FL display. 2.2. About the display on the FL display When the "STATUS" button is pressed after setting the error (protection history display) mode, a history like the one shown below is displayed, depending on the conditions. (1) Normally (when there has been no protection incident) Upper P R O T E C T H I S T O R Lower : N O...
Page 20
2.3. Clearing the protection history There are two ways to clear the protection history, as described below. (1) Start up the error (protection display) mode, display the error, then press and hold in the "ENTER" button for 3 seconds. Upper P R O T E C T H I S T O R Lower : T H E R M A L Press and hold in the "ENTER" button for 3 seconds. Upper P R O T E C T H I S T O R Lower C L E A R...
Page 21
3. DIAGNOSTIC MODE (Video/Audio (signal) path confirmation mode) d This mode is used for confirming the Video and Audio (signal) paths. (Troubleshooting) Confirming the operation of unit can be easily done after repair. Backup data will not be lost. 3.1. S tarting diagnostic mode Press the "CURSOR LEFT" and "ENTER" botton while simulltaneously pressing those two bottons of this unit. Q1, Q2 and Q3 are lit in FL display.
Page 22
Output sequence of remote control codes Confirmation item Setting and display Details of how to operate remote controller *a) Contents of confirmation Remarks ※ It is useful to form a macro program. *b) Analog or HDMI to HDMI (signal) Path Video Convert(IP Scaler) : ON, All Sources 1.Press [AMP] qZONE2 POWER OFF...
Page 23
3.5. Audio system confirmation items fig.XX : Refer to the block diagram of the fig.XXth. Output sequence of remote control codes Confirmation item Setting and display Details of how to operate remote controller Contents of confirmation Remarks ※ It is useful to form a macro program. Analog (signal) Path Input Mode : Fixed ANALOG 1.Press [AMP]...
Page 24
Output sequence of remote control codes Confirmation item Setting and display Details of how to operate remote controller Contents of confirmation Remarks ※ It is useful to form a macro program. A/D (signal) Path Amp assign : NORMAL 1.Press [AMP] qZONE2 POWER OFF ·Input : Analog / Output : Speakers (Front L/R) (Main Zone)
Page 25
Output sequence of remote control codes Confirmation item Setting and display Details of how to operate remote controller Contents of confirmation Remarks ※ It is useful to form a macro program. Amp Assign (signal) Path Amp assign : 2CH 1.Press [AMP] qZONE2 POWER OFF ·Input : Analog / Output : Speakers (SURR BACK L/R) (Amp Assign : 2CH)
Page 26
BLOCK DIAGRAM fig.1 TO DIGITAL AUDIO SPDIF/I2S/DSD SPDIF/I2S/DSD HDMI1 BUS SW FPGA XC35S400A-4FGG320C HDMI HDMI BUS HDMI2 TRANSMITTER HDMI OUT1 BUFFER ADV7511 HDMI3 HDMI Rx HDMI OUT2 IP SCALER VIDEO DECODER ADV7840 ABT2015 HDMI IN HDMI4 HDMI TO DIGITAL AUDIO I/P SCALER Tx AUDIO BUS SW FROM DIGITAL AUDIO TC74VHC244FT...
Page 27
fig.2 TO DIGITAL AUDIO SPDIF/I2S/DSD SPDIF/I2S/DSD HDMI1 BUS SW FPGA XC35S400A-4FGG320C HDMI HDMI BUS HDMI2 TRANSMITTER HDMI OUT1 BUFFER ADV7511 HDMI3 HDMI Rx HDMI OUT2 IP SCALER VIDEO DECODER ADV7840 ABT2015 HDMI IN HDMI4 HDMI TO DIGITAL AUDIO I/P SCALER Tx AUDIO BUS SW FROM DIGITAL AUDIO TC74VHC244FT...
Page 28
fig.3 SPDIF/I2S/DSD TO DIGITAL AUDIO SPDIF/I2S/DSD HDMI1 BUS SW FPGA XC35S400A-4FGG320C HDMI HDMI BUS HDMI2 TRANSMITTER HDMI OUT1 BUFFER ADV7511 HDMI3 HDMI Rx HDMI OUT2 IP SCALER VIDEO DECODER ABT2015 ADV7840 HDMI IN HDMI4 HDMI TO DIGITAL AUDIO I/P SCALER Tx AUDIO BUS SW FROM DIGITAL AUDIO TC74VHC244FT...
Page 29
fig.4 TO DIGITAL AUDIO SPDIF/I2S/DSD SPDIF/I2S/DSD HDMI1 BUS SW FPGA XC35S400A-4FGG320C HDMI HDMI BUS HDMI2 TRANSMITTER HDMI OUT1 BUFFER ADV7511 HDMI3 HDMI Rx HDMI OUT2 IP SCALER VIDEO DECODER ADV7840 ABT2015 HDMI IN HDMI4 HDMI TO DIGITAL AUDIO I/P SCALER Tx AUDIO BUS SW FROM DIGITAL AUDIO TC74VHC244FT...
Page 30
fig.5 SPDIF/I2S/DSD TO DIGITAL AUDIO SPDIF/I2S/DSD HDMI1 BUS SW FPGA XC35S400A-4FGG320C HDMI HDMI BUS HDMI2 TRANSMITTER HDMI OUT1 BUFFER ADV7511 HDMI3 HDMI Rx HDMI OUT2 IP SCALER VIDEO DECODER ABT2015 ADV7840 HDMI IN HDMI4 HDMI TO DIGITAL AUDIO I/P SCALER Tx AUDIO BUS SW FROM DIGITAL AUDIO TC74VHC244FT...
Page 31
fig.6 TO DIGITAL AUDIO SPDIF/I2S/DSD SPDIF/I2S/DSD HDMI1 BUS SW FPGA XC35S400A-4FGG320C HDMI HDMI BUS HDMI2 TRANSMITTER HDMI OUT1 BUFFER ADV7511 HDMI3 HDMI Rx HDMI OUT2 IP SCALER VIDEO DECODER ADV7840 ABT2015 HDMI IN HDMI4 HDMI TO DIGITAL AUDIO I/P SCALER Tx AUDIO BUS SW FROM DIGITAL AUDIO SUB uCOM...
Page 32
fig.8 VOLUME AND INPUT SELECTOR R2A15220FP HEADPHONE OUT R-CH Audio Selction DIRECT AVR3311/991=PHONO+6INPUT SPK OUT ANALOG INPUT AVR2311/891 FL/SBL/Z2L/FL-H AVR3311/991 FL/SBL/Z2L/Z3L/FL-H TO DSP FRONT RELAY BLOCK INPUT AVR2311/891 FR/SBR/Z2R/FR-H SIRIUS AVR3311/991 FR/SBR/Z2R/Z3R/FR-H AVR3311/991 NA Series MIC(Mini Jack) MONO MONO ZONE2 ZONE2 VOLUME NJW1194 PRE-OUT...
Page 33
fig.9 VOLUME AND INPUT SELECTOR R2A15220FP HEADPHONE OUT R-CH Audio Selction DIRECT AVR3311/991=PHONO+6INPUT SPK OUT ANALOG INPUT AVR2311/891 FL/SBL/Z2L/FL-H AVR3311/991 FL/SBL/Z2L/Z3L/FL-H TO DSP FRONT RELAY BLOCK INPUT AVR2311/891 FR/SBR/Z2R/FR-H SIRIUS AVR3311/991 FR/SBR/Z2R/Z3R/FR-H AVR3311/991 NA Series MIC(Mini Jack) MONO MONO ZONE2 ZONE2 VOLUME NJW1194 PRE-OUT...
Page 34
fig.10 VOLUME AND INPUT SELECTOR R2A15220FP HEADPHONE OUT R-CH Audio Selction DIRECT AVR3311/991=PHONO+6INPUT SPK OUT ANALOG INPUT AVR2311/891 FL/SBL/Z2L/FL-H AVR3311/991 FL/SBL/Z2L/Z3L/FL-H TO DSP FRONT RELAY BLOCK INPUT AVR2311/891 FR/SBR/Z2R/FR-H SIRIUS AVR3311/991 FR/SBR/Z2R/Z3R/FR-H AVR3311/991 NA Series MIC(Mini Jack) MONO MONO ZONE2 ZONE2 VOLUME NJW1194 PRE-OUT...
Page 35
fig.11 VOLUME AND INPUT SELECTOR R2A15220FP HEADPHONE OUT R-CH Audio Selction DIRECT AVR3311/991=PHONO+6INPUT SPK OUT ANALOG INPUT AVR2311/891 FL/SBL/Z2L/FL-H AVR3311/991 FL/SBL/Z2L/Z3L/FL-H TO DSP FRONT RELAY BLOCK INPUT AVR2311/891 FR/SBR/Z2R/FR-H SIRIUS AVR3311/991 FR/SBR/Z2R/Z3R/FR-H AVR3311/991 NA Series MIC(Mini Jack) MONO MONO ZONE2 ZONE2 VOLUME NJW1194 PRE-OUT...
Page 36
fig.12 VOLUME AND INPUT SELECTOR R2A15220FP HEADPHONE OUT R-CH Audio Selction DIRECT AVR3311/991=PHONO+6INPUT SPK OUT ANALOG INPUT AVR2311/891 FL/SBL/Z2L/FL-H AVR3311/991 FL/SBL/Z2L/Z3L/FL-H TO DSP FRONT RELAY BLOCK INPUT AVR2311/891 FR/SBR/Z2R/FR-H SIRIUS AVR3311/991 FR/SBR/Z2R/Z3R/FR-H AVR3311/991 NA Series MIC(Mini Jack) MONO MONO ZONE2 ZONE2 VOLUME NJW1194 PRE-OUT...
Page 37
fig.13 VOLUME AND INPUT SELECTOR R2A15220FP HEADPHONE OUT R-CH Audio Selction DIRECT AVR3311/991=PHONO+6INPUT SPK OUT ANALOG INPUT AVR2311/891 FL/SBL/Z2L/FL-H AVR3311/991 FL/SBL/Z2L/Z3L/FL-H TO DSP FRONT RELAY BLOCK INPUT AVR2311/891 FR/SBR/Z2R/FR-H SIRIUS AVR3311/991 FR/SBR/Z2R/Z3R/FR-H AVR3311/991 NA Series MIC(Mini Jack) MONO MONO ZONE2 ZONE2 VOLUME NJW1194 PRE-OUT...
Page 38
fig.14 VOLUME AND INPUT SELECTOR R2A15220FP HEADPHONE OUT R-CH Audio Selction DIRECT AVR3311/991=PHONO+6INPUT SPK OUT ANALOG INPUT AVR2311/891 FL/SBL/Z2L/FL-H AVR3311/991 FL/SBL/Z2L/Z3L/FL-H TO DSP FRONT RELAY BLOCK INPUT AVR2311/891 FR/SBR/Z2R/FR-H SIRIUS AVR3311/991 FR/SBR/Z2R/Z3R/FR-H AVR3311/991 NA Series MIC(Mini Jack) MONO MONO ZONE2 ZONE2 VOLUME NJW1194 PRE-OUT...
Page 39
fig.15 VOLUME AND INPUT SELECTOR R2A15220FP HEADPHONE OUT R-CH Audio Selction DIRECT AVR3311/991=PHONO+6INPUT SPK OUT ANALOG INPUT AVR2311/891 FL/SBL/Z2L/FL-H AVR3311/991 FL/SBL/Z2L/Z3L/FL-H TO DSP FRONT RELAY BLOCK INPUT AVR2311/891 FR/SBR/Z2R/FR-H SIRIUS AVR3311/991 FR/SBR/Z2R/Z3R/FR-H AVR3311/991 NA Series MIC(Mini Jack) MONO MONO ZONE2 ZONE2 VOLUME NJW1194 PRE-OUT...
Page 40
fig.16 VOLUME AND INPUT SELECTOR R2A15220FP HEADPHONE OUT R-CH Audio Selction DIRECT AVR3311/991=PHONO+6INPUT SPK OUT ANALOG INPUT AVR2311/891 FL/SBL/Z2L/FL-H AVR3311/991 FL/SBL/Z2L/Z3L/FL-H TO DSP FRONT RELAY BLOCK INPUT AVR2311/891 FR/SBR/Z2R/FR-H SIRIUS AVR3311/991 FR/SBR/Z2R/Z3R/FR-H AVR3311/991 NA Series MIC(Mini Jack) MONO MONO ZONE2 ZONE2 VOLUME NJW1194 PRE-OUT...
Page 41
fig.17 VOLUME AND INPUT SELECTOR R2A15220FP HEADPHONE OUT R-CH Audio Selction DIRECT AVR3311/991=PHONO+6INPUT SPK OUT ANALOG INPUT AVR2311/891 FL/SBL/Z2L/FL-H AVR3311/991 FL/SBL/Z2L/Z3L/FL-H TO DSP FRONT RELAY BLOCK INPUT AVR2311/891 FR/SBR/Z2R/FR-H SIRIUS AVR3311/991 FR/SBR/Z2R/Z3R/FR-H AVR3311/991 NA Series MIC(Mini Jack) MONO MONO ZONE2 ZONE2 VOLUME NJW1194 PRE-OUT...
Page 42
fig.18 VOLUME AND INPUT SELECTOR R2A15220FP HEADPHONE OUT R-CH Audio Selction DIRECT AVR3311/991=PHONO+6INPUT SPK OUT ANALOG INPUT AVR2311/891 FL/SBL/Z2L/FL-H AVR3311/991 FL/SBL/Z2L/Z3L/FL-H TO DSP FRONT RELAY BLOCK INPUT AVR2311/891 FR/SBR/Z2R/FR-H SIRIUS AVR3311/991 FR/SBR/Z2R/Z3R/FR-H AVR3311/991 NA Series MIC(Mini Jack) MONO MONO ZONE2 ZONE2 VOLUME NJW1194 PRE-OUT...
Page 43
fig.19,20,21 VOLUME AND INPUT SELECTOR R2A15220FP HEADPHONE OUT R-CH Audio Selction DIRECT AVR3311/991=PHONO+6INPUT SPK OUT ANALOG INPUT AVR2311/891 FL/SBL/Z2L/FL-H AVR3311/991 FL/SBL/Z2L/Z3L/FL-H TO DSP FRONT RELAY BLOCK INPUT AVR2311/891 FR/SBR/Z2R/FR-H SIRIUS AVR3311/991 FR/SBR/Z2R/Z3R/FR-H AVR3311/991 NA Series MIC(Mini Jack) MONO MONO ZONE2 ZONE2 VOLUME NJW1194 PRE-OUT...
Page 44
fig.23,24 VOLUME AND INPUT SELECTOR R2A15220FP HEADPHONE OUT R-CH Audio Selction DIRECT AVR3311/991=PHONO+6INPUT SPK OUT ANALOG INPUT AVR2311/891 FL/SBL/Z2L/FL-H AVR3311/991 FL/SBL/Z2L/Z3L/FL-H TO DSP FRONT RELAY BLOCK INPUT AVR2311/891 FR/SBR/Z2R/FR-H SIRIUS AVR3311/991 FR/SBR/Z2R/Z3R/FR-H AVR3311/991 NA Series MIC(Mini Jack) MONO MONO ZONE2 ZONE2 VOLUME NJW1194 PRE-OUT...
Page 47
When you repair the printing board, you can use the following JIG (Extension cable kit). Please order to DENON Official Service. Distributor in your region if necessary. Note: When the connection which is wrong in the JIG (EXTENSION UNIT KIT) is done it becomes cause of damage.
Page 48
(3) PCB HDMI is detached from the chassis, and it puts it into the state turned inside out. Please pave an insulation sheet that is larger than PCB HDMI under PCB. b Connect the ground point of PCB to the chassis with a ground lead or the like. Ground lead PCB INPUT PCB VIDEO...
Page 49
PCB HDMI Insulation sheet PCB INPUT PCB SIDE CNT Connection table of Board to Board Ref. No. Ref. No. 11 pin SIDE CNT N4908 HDMI 25 pin SIDE CNT N4907 HDMI 19 pin CP105 FRONT CNT N4910 HDMI 17 pin CP106 FRONT CNT N4911...
Page 50
ABOUT REPLACE THE MICROPROCESSOR WITH A NEW ONE When replaced of the U-PRO (Microprocessor) or the Flash ROM, confirm contents of the following. After PWB Name Ref. No. Description Remark replaced HDMI U5301 R5F64169DFD SOFTWARE: Main HDMI U5101 W19B160BBT7H SOFTWARE: Main ROM HDMI U5500 R5F3650KNFB SOFTWARE: Sub...
Page 51
Make a note of the settings before updating, and set them again after updating. 3. About the error code See the chart below for error codes, details of faults, and coping strategies when firmware updates are performed through DPMS (Denon Product Management Server). Error Details of Error code...
Page 52
Error Details of Error code Display Coping strategies Code Data acquisition failed (timed out) Check the network connection. C o n n e c t i o n f a i l when downloading Main CPU Carry out the update in an environment firmware.
Page 53
Error Details of Error code Display Coping strategies Code Connection to DPMS failed when Check the network connection. S u b * * * m i n rewriting firmware such as Sub Carry out the update in an environment C o n n e c t i o n F a i l 5 2 CPU, DSP, FPGA, and PLD.
Page 54
Error Details of Error code Display Coping strategies Code O S D * * * m i n Failure to delete data before Turn the power off then back on. rewriting serial flash. Updating starts automatically. U p d a t i n g f a i l Failure to receive firmware for serial O S D...
Page 55
Error Details of Error code Display Coping strategies Code Notification of line congestion Check the network connection. E t h e r I M G * * * m i n via DPMS access when rewriting Carry out the update in an environment DM860 related firmware (Boot S e r v e r b u s y A B...
Page 56
Device display when firmware updated Target of devide when firmware updated. Target of device Display Error cpde M a i n * * * m i n 10~15 Main 36~3C U p d a t i n g 50~52 S u b * * * m i n 54~58 U p d a t i n g...
Page 58
Simple version Basic version Advanced version Information...
Page 60
Simple version Basic version Advanced version Information...
Page 61
ADJUSTMENT Audio Section Idling Current Required measurement equipment: DC Voltmeter 1. Preparation (1) Avoid direct blow from an air conditioner or an electric fan, and adjust the unit at normal room temperature 15 °C ~ 30 °C (59 °F ~ 86 °F). (2) Presetting •...
TROUBLE SHOOTING 1. POWER 1.1. Power not turn on Power not turn on. When the power turned on, does the ON/STANDBY Is the fuse blown? Refer to 1.2.Fuse is blown. indicator on the front panel flashing green? Is a DC 5V voltage output Check for damage in the SMPS B'D Is a DC 5V voltage being...
2. Analog video MONITOR OUT (CVBS) output NG Input CVBS Input S Input Function : SAT Function : DVR COMPONENT To A To B Not output MONITOR OUT (Component) output NG "Video Convert" is set to ON. Input CVBS Input S Input COMPONENT Function : SAT Function : DVR...
Page 64
Input CVBS Check power supply voltage. V+5V : N2004-4pin REGULATOR B'D flaw. V-5V : N2004-1pin Check on set value of each IC. HDMI B'D L4900 : Check I C communication HDMI B'D flaw. waveforms. L4901 : Check I C communication waveforms.
Page 65
Input Check power supply voltage. V+5V : N2004-4pin REGULATOR B'D flaw. V-5V : N2004-1pin Check on set value of each IC. HDMI B'D L4900 : Check I C communication waveforms. HDMI B'D flaw. L4901 : Check I C communication waveforms. L4905 : H(+5V) L4906 : L(0V) Extend HDMI B'D using a jig.
Page 66
Input CVBS/S/COMPONENT Check input signal of VIDEO DECODER (U1100). HDMI B'D Check signal detection. V : L4920 HDMI B'D Input CVBS : to A S-Y : L4924 V_L4903 : H(+3.3V) Input S : to B S-C : L4925 S_L4904 : H(+3.3V) Input COPONENT : to D COMPONENT-Y : L4923 COMPONENT_L4902 : H(+3.3V)
Page 67
Input COMPONENT Check of power supply voltage V+5V : N2004-4pin REGULATOR B'D flaw V-5V : N2004-1pin Check on set value of each IC. HDMI B'D L4900 : Check I C communication HDMI B'D flaw waveforms. L4901 : Check I C communication waveforms.
Page 68
Check HDMI output setting, referring to the (5) Is the BD/DVD player's HDMI output setting correct? BD/DVD player's operating instructions. (6) When using a DENON BD/DVD player's, is the fluorescent display tube's "HDMI" indicator lit? If using a non-DENON BD/ DVD player's, proceed to "YES".
Page 69
Check TV Use an HDCP-compatible TV. PC TVs (10) Is the TV HDCP-compatible? cannot be used. If the TV is not compatible with resolutions of 1080P, no picture will be output, even (11) Is the TV compatible with resolutions of 1080P? if the BD/DVD player's resolution is set to 1080P.
Page 70
BD/DVD player, is the FL on the side on which the BD/DVD player is display's "HDMI" indicator lit? K1001/K1002/K1003) to connected. If using a non-DENON BD/ the U1100 is defective. Is communication waveform confirmed in HDMI DVD player, proceed to connector (K1100/K1101/K1102/K1001/K1002/ "NO".
Page 71
Check operation of each device. (AMP source : DVR [i/p:OFF, MONITOR OUT: MONITOR1] / Video input of player : 480P / Connect the TV.) Check operation of U1002 (ADV3002). (23) Check power supply. The power supply circuitry is defective. Are 5V or 3.3V supplied to U1002 (each power supply pin)? (24) Check RESET.
Page 72
Check operation of U1601. (30) Check power supply. Is 1.2V supplied to C1632? The power supply circuitry is defective. Is 3.3V supplied to C1656? (31) Check RESET. The RESET circuitry (Q1600 and Is RESET waveform confirmed in N1601 (1pin), when power is surrounding circuitry) or U1601 is defective.
Page 79
4. AUDIO 4.1. AUDIO CHECK AUDIO OUTPUT : NG INPUT SURROND MODE SOURCE CHECK1 Check ANALOG AUDIO BLOCK. ANALOG 2CH DIRECT ANALOG INPUT SURROND MODE SOURCE CHECK2 Check Digital AUDIO BLOCK. COAX or OPT Legacy(PCM or DolbyDigital or dts…) INPUT SURROND MODE SOURCE CHECK3 Check via AD.
Page 80
4.2. Power AMP (7CH AMP B'D) No sound is output. The protector operates. Is the power transistor open or short circuit? Replace the power transistor. 2SB1647/2SD2560 Is the emitter resistance of the power transistor open? Replace the emitter resistance. 0.47Ω Is the base resistance of the power transistor open? Replace the base resistance.
4.3. Analog audio No sound is output Is the voltage of ±8V supplied to The power supply of ±8V is repaired. SIDE CNT B'D CP6 9-12 pin? Is the audio signal transmitted to The power amplifier is repaired. AUDIO B'D CN3001? Connect the connectors properly.
Page 82
Checking the settings Set the IP address and other parameters properly. For a fixed IP setting, check Are the AVR-3311CI's network settings correct? whether the IP address is redundant with that of other devices, and check whether the subnet mask setting is correct.
Page 83
Is the USB device compatible with the set? and iPod (Remove some models) are supported. Checking the set (AVR-3311CI) Is the wire of N4201 properly connected? Connect the wire properly. Is a voltage (5V) being supplied between pins 1 and 4 of Jack602...
Page 84
5.3. No picture or sound is output Checking the set (AVR-3311CI):(If no picture is output) Are video signals output from U4203 pin 27 (Y) and pin 24 (C)? You do not use the USB hub. Check the analog video circuit.
Page 85
CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK Wave form CH1: D-DATA CH1: DATA CH2: fs CH3: 64fs CH1: DATA CH2: fs CH3: 64fs CH4: 256fs...
Page 86
LAEVEL DIAGRAM LEVEL DIAGRAM FRONT ch R2A15220FP ANALOG H/POUT SPEAKER + LINE IN GAIN ADJ. + AK4358VQ + (AVR3311 ONLY) AK5358B + - - MUTE PRE OUT ZONE2 (AVR2311/3311 ONLY) ZONE3 (AVR3311 ONLY) (AVR3311ONLY) RECOUT1 RECOUT2 EXT IN +30dB 4.34Vrms/8Ω SPK OUT FULL SCALE LEVEL=3Vrms AK4358VQ...
Page 87
LEVEL DIAGRAM CENTER ch R2A15220FP SPEAKER + GAIN ADJ. AK4358VQ + + (AVR3311 ONLY) - - MUTE PRE OUT EXT IN +30dB 4.2Vrms/8Ω SP OUT MAX SIGNAL LEVEL +20dB +20dB 0dBFS=1.77Vrms +29dB +10dB +10dB -10dBFS L.P.F GAIN=+1.6dB 213mVrms EXT IN -3dB 200mV 0dB...
Page 88
LEVEL DIAGRAM SUBWOOFER ch R2A15220FP SPEAKER + GAIN ADJ. AK4358VQ + + (AVR3311 ONLY) - - MUTE PRE OUT EXT IN +30dB 4.74Vrms SW ch DAC MAX SIGNAL LEVEL PRE OUT Config1(S/S/S/Y)DOLBY LIMIT LEVEL=2.5Vrms (5.1ch-3dBFS at 30Hz) +11dB AK4358VQ +20dB +20dB 0dBFS=1.77Vrms 1.37mVrms...
Page 89
LEVEL DIAGRAM SURROUND ch R2A15220FP SPEAKER + GAIN ADJ. AK4358VQ + + (AVR3311 ONLY) - - MUTE PRE OUT EXT IN +30dB 4.2Vrms/8Ω SP OUT MAX SIGNAL LEVE AK4358VQ +5dB +20dB +20dB 0dBFS=1.77Vrms +29dB +10dB +10dB -10dBFS L.P.F GAIN=+5dB 218mV -3dB 200mV 0dB...
Page 90
LEVEL DIAGRAM SURR.BACK ch R2A15220FP SPEAKER + GAIN ADJ. AK4358VQ + (AVR3311 ONLY) + - - MUTE PRE OUT (AVR2311/3311 ONLY) from from ZONE2 ZONE2 from ZONE3 (AVR3311 ONLY) +30dB 4.2Vrms/8Ω SP OUT AK4358VQ MAX SIGNAL LEVE +20dB +20dB 0dBFS=1.77Vrms +1.6dB +29dB +10dB...
Page 91
R2A15220FP LEVEL DIAGRAM SB-ch FRONT/ZONE ASIGN 0dB ZONE2/3 from F-ch from SPEAKER DA SB-ch + LINE IN + MAIN from EXT.IN SB-ch AVR2311/3311, ZONE2 NJW1194 ONLY TONE MONO MUTE PREOUT MONO AVR3311 ONLY ZONE3 NJW1194 TONE MONO MUTE PREOUT MONO +30dB SP OUT 4.48Vrms/8Ω...
Page 95
SPK (FOIL SIDE) 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
Page 96
REG (COMPONENT SIDE) FRONT_CNT (COMPONENT SIDE) REG_CNT (COMPONENT SIDE) 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
Page 97
REG (FOIL SIDE) FRONT_CNT (FOIL SIDE) REG_CNT (FOIL SIDE) 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
Page 98
SIDE_CNT (COMPONENT SIDE) SIDE_CNT (FOIL SIDE) USB (COMPONENT SIDE) USB (FOIL SIDE) MIC (COMPONENT SIDE) MIC (FOIL SIDE) 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
Page 99
FRONT (COMPONENT SIDE) FUNCTION_CNT (COMPONENT SIDE) V.AUX (COMPONENT SIDE) 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
Page 100
FRONT (FOIL SIDE) FUNCTION_CNT (FOIL SIDE) V.AUX (FOIL SIDE) 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
Page 114
REG_SIRIUS_COMMON CNT 2/4 SIDE CONNECTOR TO RC-5 TO RC-5 PAGE 8(A4) PAGE 8(A1) OPTION A OPTION B MODEL MODEL AVR1611 AVR1611 AVR1911 AVR1911 OPTION_B AVR2311 AVR2311 AVR3311 AVR3311 OPTION_A IC109 C125Z2-15P C125Z2-19P PQ033DNA1ZPH E3 ONLY CP802 OPEN 10/50 IC1A:A 10/50 M3.3V 232IMO 232OMI...
Page 116
R418 D5V(MX) OPEN REG_SIRIUS_COMMON CNT 4/4 Q406 SWM5V(MX) OPEN SWM3.3V R419 OPEN Q404 R401 OPEN(2W) M3.3V Q401 OPEN C419 C470 D/MGND R402 OPEN(2W) OPEN OPEN OPEN SIRIUSMO R403 OPEN(2W) R404 SIRIUSMI OPEN(2W) SIRIUS/RS232C/TRIGGER SIRIUSRST A+8V D401 OPEN A+8V A-8V Q402 A-8V OPEN R405...
Page 117
TO FRONT CNT AVR /891ONLY TO FRONT CNT PAGE 7(J5) PAGE 7(H5) TO SIDE CNT R3000 PAGE 6(G7) OPEN AUDIO CN3000 R3001 CX3001 AUDIO IN IC3000:B R3002 CX3000 AZ4580 R3004 C3000 R3003 10/50 R3006 R3007 C3017 R3005 R3008 PHONO_L 10/50 R3009 R3010 R3011...
Page 119
P_A-7V R4000 D4000 1N4007 C4000 100/50 D4001 1N4007 D4002 1N4007 R4354 P_PREZ2L. P_PREZ2L R4001 R4002 C4002 22/50 R4003 R4342 C4001 R4004 R4005 22/50 OPEN OPEN IC4008:A Q4000 Q4001 OPEN OPEN KTC2875B R4010 C4004 10N-K IC4008:B R4012 470K Q4002 R4013 R4014 OPEN OPEN KRA104S...
Page 120
C4066 OPEN R4154 R4157 R4158 R4155 OPEN OPEN OPEN OPEN R4153 C4065 R4156 OPEN OPEN R4159 R4160 OPEN OPEN OPEN Q4052 Q4053 OPEN OPEN R4167 R4168 OPEN OPEN IC4003:A IC4002:A OPEN Q4050 Q4051 OPEN Q4054 Q4055 OPEN R4172 OPEN OPEN OPEN OPEN R4171...
Page 121
PAGE 7(C4) PAGE 7(E4) PAGE 7(B4) PAGE 5(B3) N2005 TO CNT B’D TO CNT B’D TO CNT B’D TO CNT B’D 4311 only OPEN AVR3311 AVR2311 CHIP_J AVR991 AVR891 D2001,D2002 KDS4148U KDS4148U D2005,D2006 D2003,D2007 KDS4148U KDS4148U D2004,D2008 KDS4148U OPEN C2006-C2008 C2047,C2060 22/16 22/16...
Page 122
TO S/CVBS K1011 RCA-303B1-10 K1013 RCA-303B1-1 0 COMPONENT VIDEO IN K1001 K1003 OPEN C1001 10/6.3 IN2Y OPEN Z1_YOUT R1049 R1001 R1040 OPEN MONITOR1 K1001 OPEN K1003 10/6.3 C1002 IN2CB OPEN Z1_CBOUT R1050 R1002 R1041 OPEN K1001 OPEN K1003 10/6.3 IN2CR C1003 OPEN Z1_CROUT...
Page 123
TO COMPONENT TO COMPONENT N3003 OPEN CB-G MONITOR CR-G MONIL1 LINE1 MONIL2 LINE2 MONIL3 LINE3 N3001 OPEN CB-G CR-G LINE1 VIN1L1 LINE2 VIN1L2 LINE3 VIN1L3 D-TERMINAL N3002 OPEN JAPAN LINEA LINEB ON CHANNEL CB-G VIDEO-2 CR-G Q3001 LINE1 VIN2L1 ASPECT_H OPEN MUTE LINE2...
Page 124
OPEN OPEN HPDF HPD/HEAC- C21 0.1/10 KRC102S KRC104S OPEN DDCDATA DDCCLK UTILITY/HEAC+ CE_Remote 0.1/10 CKshield R17 OPEN 23P-FFC DOshield TXEN. TXEN. HPDF CE C D1shield DDC_SDA DDC_SCL HDMI5V D2shield CEC5V CEC3.3V OPEN DGND RX_C- RX_C+ RX_0- HDMI BRACKET RX_0+ OPEN RX_1- RX_1+ RX_2-...
Page 138
TO DM860 C4230 OPEN C4231 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 OPEN R4232 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OPEN SRCMUTE C4232 SRCDATA SRCDATA OPEN SRC64fs...
Page 139
TO MAIN CPU USB TCC8600 8U-310051(16/21) DIGITAL_UNIT DIGITAL NET3.3V NET1.8V SUPPLY DGN D R4410 OPEN R4447 OPEN R4411 OPEN U4404 C4455 C4458 OPEN OPEN OPEN C4459 JTAG OPEN N4400 L4402 OPEN OPEN VSS2 R4431 TCKUSB CVDD MCLKUSB OPEN GND_D1 TDOUSB BCKoUSB MCLK BICK...
Page 140
L4625 BLM21PG221 L4626 BLM21PG221 L4627 BLM21PG221 D3.3V-1 N4600 OPEN N4610 D5.2V 5P-BASE(SMW250) D5.2V L4600 L4615 DGN D BLM21PG221 20 PVIN VOUT OPEN D3.3V-1 DGN D 1.48A 21 PVIN VOUT MAINPOWER L4628 11A121 U4601 22 NC L4616 L4601 23 NC EX3AV BLM21PG221 OPEN 24 NC...
Page 141
TO DIGITAL SUPPLY L5028 OPEN SWM5V L5029 OPEN L5030 OPEN REMOTE3.3V L5031 OPEN SWM3.3V M3.3V L5032 OPEN L5033 OPEN L5034 OPEN N4907 L5035 OPEN 25P-SOCKET(C125Z2) L4927 OPEN D5V(MX) SWM5V(MX) SWM3.3V M3.3V DA+5V D/MGN D DA+7V SIR_MO5/RDSDA L5005 OPE N SIR_MO/RDS_DATA DA-7V SIR_MI5/RDSCK L5006...
Page 143
TO_LEVEL_CHG R5322 R5311 R5317 2.7K R5401 R5304 R5309 R5312 R5318 OPEN OPEN Q5302 OPEN SWM3.3V R5384 4.7K M3.3V R5385 4.7K DGND R5323 M AINPOWER R5308 MAINPOWER R5303 R5313 R5319 M _RESET 4.7K M_RESET 4.7K 2.7K BDOWN BDOWN R5305 R5310 N5300 OPEN OPEN R5314...
Page 144
TO HDMI RX TO VIDEO ENCODER TO HDMI TX TO GUI PLD SCPU5V R5527 4.7 K SCPU3.3V R5528 4.7 K DGND SUBBDOWN R5529 4.7 K SUBBDOWN R5530 4.7 K PLDAERR. PLDAERR. MPLDCLK MPLDCLK MPLDDATA MPLDDATA MPLDCSMAIN MPLDCSMAIN SUBTCK DV_POWER1 SUBTMS CEC_POWER SUBTDI SUBTDO...
Page 146
WIRING DIAGRAM d AC CORD FRONT WIDE B'D SIRIUS UNIT SPK UNIT 2P WIRE (FRONT.WIDE GND) DIGITAL UNIT 23P CARD CABLE (FRONT HDMI) 5P WIRE (DIGITAL PWR) VIDEO UNIT FRONT CNT UNIT AUDIO IN UNIT PREOUT OUT UNIT (S4) MAIN TRANS REG_CNT UNIT (S2) (S1)
Page 147
EXPLODED VIEW s WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. E2, E1C only E2, E1C only E3 only E2, E1C only (INLET) G x2 T x2 (HDMI&SIRIUS) E3 only...
Page 148
7 963412006600D KNOB FUNCTION 5088212078010SZ PCB FRONT_CNT 8 00D1140203009 KNOB RING F 5087212201000S 8 00D1140203025 KNOB RING F 5087212201100S PCB FRONT ASSY 7025HK0920013 9 00D1310169038 BADGE DENON 5630210028300S PCB FRONT ASSY BKE2 7025HK0920053 9 00D1310169041 BADGE DENON 5630210028400S PCB FRONT ASSY SPE2...
Page 149
Ref.No. Part No. Part Name Remarks Q'ty New Personal notes: BRACKET SUPPORTER 4010210206000S 44 963101009540S POWER TRANS 8200960750240S 44 963101009550S POWER TRANS 8200960750210S 44 963101009560S POWER TRANS SPE1C 8200960750220S HEAT SINK MAIN 2120211798000S BRACKET HEATSINK MAIN 4010214906000S BRACKET HDMI 4010214896000S SUPPORTER PCB 4070211653000S BRACKET H SINK...
Page 151
PACKING VIEW s E2,E1C model E3 model 6 16 17 18 19 SP model 25 26 30 E1C model E2 model E1C model E1C model SP model...
Page 152
PARTS LIST OF PACKING & ACCESSORIES s zParts for which "nsp" is indicated on this table cannot be supplied. zPart indicated with the mark " ★ " is not illustrated in the exploded view. zThe parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks"...
Page 153
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F64169DFD (HDMI : U5301) (Note 1) IIO0_0 / IIO1_0 / D8 / P1_0 P4_4 / CS3 / A20 / CTS6 / RTS6 / SS6 AN0_7 / D7 / P0_7 P4_5 / CS2 / A21 / CLK6 AN0_6 / D6 / P0_6...
Page 154
R5F64169DFD Terminal Functions Pin Name Synbol I/O Type Pullup STBY stop Function 1 P96/(TXD4) SIRIUS RST O/L NC 2 P95/(CLK4) HD RADIO RST/ST IND O/O/I C/C/- O/L HD RADIO control pin /ANALOG TUNER control 3 P94/(CTS4)/TB4IN O/L NC 4 P93/(CTS3)/TB3IN O/L NC 5 P92/TXD3/SDA3 HDRADIO MOHI/TU SDA O/I_O O/L HD RADIO control/ANALOG TUNER control...
Page 155
Master Volume rotation detect input (Rotary encoder) 67 P126 VSEL B SW3VPu Master Volume rotation detect input (Rotary encoder) SUB UPDATE mode control (DPMS/DENON WRITTER). 68 P125 SUB UPDATE Normal:L. SUB rewriting mode:H(SUB reset) 69 P47/CS0/(A23) O/L External memory access pin(Connection:CS#)
Page 156
Pin Name Synbol I/O Type Pullup STBY stop Function 123 P157 ZVOL DATA O/L ZONE VOL(NJW1194) control 124 P156 E SPI REQ O/L ETHERNET communication control pin 232C CONTROL 125 P155/(RXD6) O/L SUB LOG MODE : For 232C course switch control (SUB LOG MODE) 126 P154/(TXD6) TUNED...
Page 158
ABT RST IP CONV(ABT2015) Reset 20 P80/(RXD5) 21 P77/(CLK5) SUB TDO PLD rewriting control (JTAG) A PLD control pin/ DENON WRITTER 22 P76/(TXD5) A PLD CS /"D/M" / MITSUBISHI rewritten for determining (DW :L) 23 P75 A PLD DATA A PLD control pin...
Page 159
Pu/Pd PURE CEC Pin Name Synbol I/O Type Det P.OFF Function (Int.) (Ext.) STBY 58 P32 DAC MDI DAC control pin (ASK4358) 59 P31 DAC MC DAC control pin (ASK4358) 60 VCC +3.3V 61 P30 DAC MS DAC control pin (ASK4358) 62 VSS 63 P27 DAC RST...
Page 163
SECTION 5: PIN AND PACKAGE INFORMATION This section shows the pinout of the ADV7511 100-lead LQFP package. This section also contains a brief description of the different pins as well as the mechanical drawings 100-lead LQFP configuration (top view - not to scale) Figure 6 ADV7511BSTZ (HDMI : U1801) PIN 1...
Page 165
IS42S32200E6TL Terminl Function Pin No. Signal Pin No. Signal Pin No. Signal Pin No. Signal DATA28 DATA27 IOVDD IOVDD ADDR0 SDCAS IOVDD ADDR2 SDRAS DATA26 ADDR1 SDCKE DATA25 ADDR4 SDWE DATA24 ADDR3 TRST DATA23 ADDR5 SDA10 IOVDD DATA22 SDCLK0 DATA21 IOVDD CLK_CFG0 DATA20 ADDR6 BOOTCFG0...
Page 166
LC89058W-E (HDMI : U2805,U2806,U2807) 35 34 33 32 31 30 29 28 27 26 25 SDIN SLRCK SBCK RDATA XMODE RLRCK LC89058W-E DV DD DGND DGND DV DD RBCK GPIO0 GPIO1 RMCK GPIO2 AGND GPIO3 AV DD RXOUT2 * : Pull-down resistor internal at no selection Pin Functions RXOUT1 RX0-6 input S/PDIF through output pin 1...
Page 167
LC89058W-E Continued from preceding page. Pin No. Name Function DGND Digital GND DV DD Digital power supply (3.3V) XMCK Oscillation amplifier clock output pin XOUT Output pin connected to the resonator External clock input pin, connected to the resonator (12.288MHz/24.576MHz) DV DD Digital power supply DGND...
Page 168
ADSP21367KSWZ2A (HDMI : U3200) PIN 1 INDICATOR TOP VIEW (PINS DOWN) ADSP21367KSWZ2A Terminal Function Pin No. Signal Pin No. Signal Pin No. Signal Pin No. Signal DATA28 DATA27 IOVDD IOVDD ADDR0 SDCAS IOVDD ADDR2 SDRAS DATA26 ADDR1 SDCKE DATA25 ADDR4 SDWE DATA24 ADDR3 TRST DATA23 ADDR5 SDA10 IOVDD...
W9864G2IH W9864G2IH-6 Pin description 5. PIN DESCRIPTION PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. Row address: A0−A10. Column address: A0−A7. 24, 25, 26, 27, 60, 61, 62, A0−A10 Address A10 is sampled during a precharge command to 63, 64, 65, 66 determine if all banks are to be precharged or bank selected by BS0, BS1.
Page 172
EN29LV160BB (HDMI : U3202,U5101) BYTE# DQ15/A-1 DQ14 DQ13 Standa rd DQ12 TSOP RESET# DQ11 RY/BY# DQ10 EN29LV160BB Block Diagram Block Diagram RY/BY# DQ0-DQ15 (A-1) Block Protect Switches Erase V oltage Generato r Input/Output Buffers State Control Program Voltage Generato r Command Chip Enable Regi s ter Data Latch Output Enable Logic...
Page 176
DSDL4 DAC4 DSD Lch Data Input Pin DSDR4 DAC4 DSD Rch Data Input Pin DSDL1 DAC1 DSD Lch Data Input Pin DSDR1 DAC1 DSD Rch Data Input Pin DSDL2 DAC2DSD Lch Data Input Pin DSDR2 DAC2 DSD Rch Data Input Pin DSDL3 DAC3 DSD Lch Data Input Pin DSDR3...
Page 177
HY27UF081G2A-TPCB (HDMI : 3901) HY27UF081G2A-TPCB Pin Function Pin Name Description DATA INPUTS/OUTPUTS IO0-IO7 The IO pins allow to input command, address and data and to output data during read / program IO8-IO15(1) operations. The inputs are latched on the rising edge of Write Enable (WE). The I/O buffer float to High-Z when the device is deselected or the outputs are disabled.
Page 179
W9825G6EH-6J (HDMI : U3902) DQ15 DQ14 DQ13 DQ12 DQ11 DQ10 LDQM UDQM A10/AP W9825G6EH-6J Block Diagram CLO CK BUFFER CO NTRO L SIG NAL G ENERATO R CO MMAND DECO DER CO LUMN DECODER COLUMN DECO DER CELL ARRAY CELL ARRAY BANK #1 BANK #0 MO DE REGIST ER SENSE AMPLIFIER...
Page 180
W9825G6EH W9825G6EH-6J Pin Description 5. PIN DESCRIPTION PIN NUMBER PIN NAME FUNCTION DESCRIPTION Multiplexed pins for row and column address. 23−26, 22, Address A0−A12 29−36 Row address: A0−A12. Column address: A0−A8. Select bank to activate during row address latch time, or 20, 21 BS0, BS1 Bank Select bank to read/write during address latch time.
Page 182
±15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWR in a Small Footprint Datasheet LAN8700 Pin Description Table 2.1 LAN8700/LAN8700I 36-PIN QFN Pinout PIN NO. PIN NAME PIN NO. PIN NAME nINT/TX_ER/TXD4 RX_DV RX_CLK/REGOFF CRS/PHYAD4 RX_ER/RXD4 MDIO TXCLK nRST TXD0 TX_EN TXD1...
Page 183
SA7121 (HDMI : U4203) 33 V SSA2 res. V SSA1 V DDA3 CVBS V SSD1 res. SAA7120 V DDD1 V DDA2 SAA7121 RCV1 res. RCV2 V DDA1 res. MBH790 SA7121 Block Diagram V DDA1, handbook, full pagewidth RCV1 TTXRQ XTALO V DDA2 , V DDA4 V DDA3 RESET SDA SCL RCV2...
Page 184
Digital Video Encoder (ConDENC) SAA7120; SAA7121 SA7121 Pin Description PINNING SYMBOL DESCRIPTION − res. reserved test pin; connected to digital ground for normal operation test pin; connected to digital ground for normal operation line-locked clock; this is the 27 MHz master clock for the encoder digital ground 1 SSD1 digital supply voltage 1...
Page 185
CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control BLOCK DIAGRAM AND PIN CONFIGURATION (TOP VIEW) R2A15220FP (AUDIO : IC3003) TRER MUTE AVEE AVCC BASSR2 AVEE BASSR1 ADCL 0/-6/-12/-18dB ADCR TREL SUB2 AGND BASSL2 MAIN INR1 BASSL1 Bass/ Treble 0~-95dB, +42~0dB -14~+14dB -∞...
Page 186
R2A15220FP R2A15220FP CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control PIN DESCRIPTION R2A15220FP Pin Function PIN No. Function Name FROUT,FLOUT, 22,20, COUT,SWOUT, 16,14, Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel SROUT, SLOUT, 10, 8, SBROUT,SBLOUT 2, 100 23,19, FR Pre-out,FL Pre-out, Pre-output pin of FL/FR/SL/SR/SBL/SBR channel 11, 7, SR Pre-out, SL Pre-out, 3, 99...
Page 187
G G I I I I BLOCK DIAGRAM NJW1194A (AUDIO : IC3007,IC3011) ...
Page 190
PARTS LIST OF P.C.B. UNIT s zParts for which "nsp" is indicated on this table cannot be supplied. zPart indicated with the mark " ★ " is not illustrated in the exploded view. zThe parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks"...
Page 194
PCB SPK ASS'Y d Ref. No. Part No. Part Name Remarks Q'ty New SEMICONDUCTORS GROUP z IC100 963239010480S IC PC123X2YFZ (DIP4P SHARP) K614123000010S z IC102 231010091708S IC TOP258MG G200258000010S IC116 212050010508S IC KIA2431AP J126243118010S Q1-5 00D9630120704 TR KRA102S(PB) J520010200210S 00D9630120704 TR KRA102S(PB) J520010200210S Q8-12...
Page 196
Ref. No. Part No. Part Name Remarks Q'ty New 00D9600095801 D,ZENER MTZJ6.8B K06006R844520S RLY1 00D9630218409 RELAY BC3-12 24V 2A G680240202030S RLY2-5 963682002440S RELAY 12V 5A SPK G680120502050S RLY7,8 963682002440S RELAY 12V 5A SPK G680120502050S z F100 963652010510S FUSE T2A/250V N751502001160S z F100 963652010500S FUSE T1.6A/250V...
Page 197
PCB REG_CNT ASS'Y Ref. No. Part No. Part Name Remarks Q'ty New SEMICONDUCTORS GROUP 00D2631289900 IC AZ4580M-TRE1-SOIC8P J121458000020S IC103 00D2630809006 IC NJM7805FA J126780500130S IC104 00D2630554005 IC NJM7905FA J126790500020S IC105 00D2630809006 IC NJM7805FA J126780500130S IC106 00D2630810008 IC NJM7808FA J126780800030S IC107 00D2630503001 IC NJM7908FA J126790800020S IC108...
Page 204
PCB AUDIO ASS'Y Ref. No. Part No. Part Name Remarks Q'ty New SEMICONDUCTORS GROUP IC3000 00D2631289900 IC AZ4580M J121458000020S IC3003 235810045600S IC R2A15220FP J084152200010S IC3005,3006 00D2631289900 IC AZ4580M J121458000020S IC3007 00D2623727904 IC NJW1194A J084119400010S IC3008-3010 00D2631289900 IC AZ4580M J121458000020S IC3011 00D2623727904 IC NJW1194A J084119400010S...
Page 208
PCB HDMI ASS'Y Ref. No. Part No. Part Name Remarks Q'ty New SEMICONDUCTORS GROUP IC,LOGIC AD8195 J040819505510S 00D2623425905 IC,LOGIC LTC4300/MSOP8P J040430005500S U1001 234810018506S IC,LOGIC TC74VHC4052AFT J040744052080S U1002 236810057606S IC,LOGIC ADV3002BSTZ J040300205510S U1100 IC ADV7840 J040784005510S U1101 IC PQ018ENA1ZPH J126018010030S U1600 963142010720S CERAMIC CHIP 48MHz SMD2520 E85548R000020S...
Page 209
Ref. No. Part No. Part Name Remarks Q'ty New U4606 IC PQ033DNA1ZPH J126033010010S U4607 IC PQ033DNA1ZPH J126033010010S U4608 234810015507S IC BU4248F J126424800010S U5100 00MHC007805KZ IC TC74VHCT125AFT J040741255580S IC MEMORY FLASH U5101 963243011550S 8952331100030 (EN29LV160BB-70TIP) U5102 234810014504S IC MC14094BDTR2G J040140940020S U5103 00D2623437906 IC TC74VHCT244AFT J040742445540S...
Need help?
Do you have a question about the AVR-3311CI and is the answer not in the manual?
Questions and answers