Denon AVR-3311 Owner's Manual page 11

ENGLISH
Set up speakers (Audyssey ® Auto Setup)
STEP 1
Preparation
4
&RQQHFW WKH VHWXS PLFURSKRQH WR WKH
6(783 0,& MDFN RI WKLV XQLW
When the setup microphone is
connected, the following screen is
displayed.
$872 6(783
$8'<66(< $872 6(783 0XOW(4 ;7
67(3 3UHSDUDWLRQ
&RQQHFW WKH VSHDNHUV
DQG SODFH WKHP DFFRUG
LQJ WR WKH UHFRPPHQGD
WLRQV LQ WKH PDQXDO
6HW WKH IROORZLQJ
LWHPV LI QHFHVVDU\
$PS $VVLJQ
&KDQQHO 6HOHFW
$XWR 6HWXS 6WDUW
(17(5 (QWHU 5(7851
6WDUW $XWR 6HWXS
Here, we explain setup using the example of
5.1-channel speaker playback.
For settings other than 5.1-channel surround,
select "Amp Assign" and perform step 3 and 4 of
"Set up "Amp Assign"" (vpage 53).
If unused channels are set with "Channel Select",
measuring time can be shortened. For setting,
perform steps 5 to 10 of "Set up "Channel
Select"" (vpage 53).
5
8VH ui WR VHOHFW ³$XWR 6HWXS 6WDUW´
DQG WKHQ SUHVV 
ENTER
8
Remote control operation
buttons
STEP 2
Speaker Detection
• In STEP 2, you will perform measurements at the
main listening position.
• This step automatically checks the speaker
configuration and speaker size, and calculates the
channel level, distance, and crossover frequency.
It also corrects distortion in the listening area.
6
6HOHFW ³0HDVXUH´ DQG WKHQ SUHVV

ENTER
When measuring begins, a test tone is
output from each speaker.
• Measurement requires several minutes.
7
7KH GHWHFWHG VSHDNHUV DUH GLVSOD\HG
>@
$872 6(783
$8'<66(< $872 6(783 0XOW(4 ;7
67(3 6SNU 'HWHFW &KHFN
)URQW <HV
&HQWHU <HV
6XEZRRIHU <HV
6XUURXQG <HV
&DQFHO
5HWU\
1H[W 0HDVXUHPHQW
(17(5 (QWHU
*R WR 6WHS  0HDVXUHPHQW DIWHU VSHDNHU FKHFN
NOTE
If a connected speaker is not displayed, the
speaker may not be connected correctly. Check
the speaker connection.
8
8VH ui WR VHOHFW
0HDVXUHPHQW´ DQG WKHQ SUHVV
Move the cursor
(Up/Down/Left/Right)
NOTE
If "Caution" is displayed:
Go to "Error messages" (vpage 10), check
any related items, and perform the necessary
procedures.
If the problem is resolved, return and restart
"Audyssey Auto Setup".
When performing Audyssey Auto
Setup over again
ui
Press to select "Retry", and then press
When measuring has stopped
Press RETURN , to the "Cancel Auto Setup?"
prompt is displayed.
o
Press to select "Yes", then press
>@
Setting up the speakers again
Repeat the operation from step 4 of
STEP1 Preparation .
5(7851 &DQFHO
³1H[W
1

ENTER
Confirm the setting
STEP 3
Measurement
• In STEP 3, you will perform measurements at
multiple positions (two to eight positions) other
than the main listening position.
• You can achieve a more effective correction of
distortion within the listening area by performing
measurements at multiple positions.
9
0RYH WKH VHWXS PLFURSKRQH WR
SRVLWLRQ  XVH
³0HDVXUH´ DQG WKHQ SUHVV
The measurement of the second position
ENTER starts. Measurements can be made in up to
.
eight positions.
$872 6(783
$8'<66(< $872 6(783
67(3 0HDVXUHPHQW
3OHDVH SODFH WKH PLF
ENTER
.
URSKRQH DW HDU KHLJKW
DW QG OLVWHQLQJ
SRVL LRQ
0HDVXUH
1H[W &DOFXODWLRQ
(17(5 (QWHU
6WDUW QH[W PHDVXUHPHQW 7HVW 7RQH ZLOO VWDUW
If you want to omit measurements from the next
position onward, select "Next 1 Calculation".
(Go to STEP4 Calculation
10
5HSHDW VWHS  PHDVXULQJ SRVLWLRQV 
WR 
When measurement
completed, a "Measurements finished."
message is displayed.
$872 6(783
$8'<66(< $872 6(783
67(3 0HDVXUHPHQW
0HDVXUHPHQWV ILQLVKHG
5HWU\
1H[W &DOFXODWLRQ
(17(5 (QWHU
3URFHHG WR 6WHS  $QDO\]H
Return to previous menu
ui WR VHOHFW

ENTER
0XOW(4 ;7
>@
5(7851 &DQFHO
)
of position 8 is
0XOW(4 ;7
>@
5(7851 &DQFHO