Advertisement
Quick Links
www.rvm.com.au
- Please follow these assembly instructions as it will save you time, make
assembly easier and prevent possible damage to your new unit.
- We strongly recommend that the unit is assembled on a soft surface such
as carpet or blanket.
as power tools can strip threads if over tightened.
- Correct assembly is your responsibility.
- When moving this furniture item, always carry the unit. Dragging or
sliding the unit could damage the unit and the floor surface.
Assembly Instruction Manual
MODEL NO.: NOVA1800
115 - 179
Advertisement
Related Manuals for Tauris NOVA1800
Summary of Contents for Tauris NOVA1800
- Page 1 Assembly Instruction Manual MODEL NO.: NOVA1800 www.rvm.com.au 115 - 179 - Please follow these assembly instructions as it will save you time, make assembly easier and prevent possible damage to your new unit. - We strongly recommend that the unit is assembled on a soft surface such as carpet or blanket.
- Page 2 NOTE: PLEASE CHECK YOU HAVE ALL THE CORRECT PARTS LISTED BELOW BEFORE YOU START ASSEMBLING YOUR TV CABINET Left Hand Right Hand Left Hand Right Hand 8 x 1pc 9 x 1pc Cable Management Base Front Leg Rear Leg Cross Rail Drawer Back Left Hand Right Hand...
- Page 3 OVERVIEW...
- Page 4 23 x 2pcs 24 x 2pcs 23 x 2pcs 24 x 2pcs arrowhead on cam points toward to the hole on the panel edge. 23 x 8pcs 24 x 8pcs 25 x 8pcs 34 x 3 23 x 8pcs 24 x 8pcs 34 x 3pcs 25 x 8pcs 27 x 4pcs...
- Page 5 27 x 8pcs 22 x 2 27 x 8 26 x 8pcs 26 x 8pcs 25 x 8pcs 25 x 8pcs...
- Page 6 1. HAND TIGHTEN THREADED BAR(30) INTO THE LEG FITTING FIRST 2. SLIDE CROSS RAIL(10) ONTO THREADED BAR(30) 30 x 4 3. TIGHTEN NUTS WITH THE SPANNER PROVIDED(31) 28 x 4 29 x 4 31 x 4 32 x 8pcs 32 x 8pcs ALIGN AND LIGHT L Y TIGHTEN ALL 8 SCREWS BEFORE FUL LY TIGHTENING ALL SCREWS...
- Page 7 (2 TOP DRAWERS) -NOTE HANDLE GROOVE POSITION 23 x 10pcs 24 x 10pcs 26 x 10pcs arrowhead on cam points toward to the hole on the panel edge. (2 BOTTOM DRAWERS) 23 x 10pcs 24 x 10pcs 26 x 10pcs arrowhead on cam points toward to the hole on the panel edge.
- Page 8 27 x 4pcs...
- Page 9 NOTE: For gyprock walls ensure you locate the studs, or use appropriate to the wall. (also see Step 12) Use a screw driver to fasten the screws (Part 26) into the wall.
- Page 10 Use a screw driver to fasten the screws (Part 40) into the bracket.
- Page 11 Drawer Front Alignment Drawer front panel If the drawer front panel is NOT level after being assembled, then... Drawer front panel Drawer Side Drawer Runner Loosen the screw Adjust the slide up or down Loosen the screws on the left and right hand side, then move the drawer slide up or down, untill the drawer fronts are even/level, then tighten the screws...
- Page 12 MODEL NUMBER OF THE UNIT PURCHASED DESCRIPTION/PART NUMBER OF THE MISSING OR FAULTY PART QUANTITY OF THE PARTS NEEDED If for whatever reason you cannot get in contact with the store, please get in contact with Tauris direct at http://www.rvm.com.au/contact/ Product of RVM Australia...
-
Page 13: Warranty Policy
WARRANTY POLICY 1. Nothing in this Warranty affects the Consumer’s rights under the Australian Consumer law. The benefits to the Consumer under this Warranty are in addition to the rights and remedies of the buyer under any Consumer Guarantees. The Australian Consumer Law requires that we confirm that: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. - Page 14 b.) Make note of the defects reported by the Owner. c.) Take back the defective goods from the owner and determine within a reasonable time through dialogue with the Seller whether the goods are defective. d.) Advise the owner within a reasonable time frame whether it accepts or rejects the Product claim.
Need help?
Do you have a question about the NOVA1800 and is the answer not in the manual?
Questions and answers