Advertisement
Quick Links
www.rvm.com.au
168 -296
- Please follow these assembly instructions as it will save you time, make
assembly easier and prevent possible damage to your new unit.
- We strongly recommend that the unit is assembled on a soft surface such
as carpet or blanket.
as power tools can strip threads if over tightened.
- Correct assembly is your responsibility.
- When moving this furniture item, always carry the unit. Dragging or
sliding the unit could damage the unit and the floor surface.
Assembly Instruction Manual
MODEL NO.: TITAN1800
Advertisement
Related Manuals for Tauris TITAN1800
Summary of Contents for Tauris TITAN1800
- Page 1 Assembly Instruction Manual MODEL NO.: TITAN1800 www.rvm.com.au 168 -296 - Please follow these assembly instructions as it will save you time, make assembly easier and prevent possible damage to your new unit. - We strongly recommend that the unit is assembled on a soft surface such as carpet or blanket.
- Page 2 21 x40 22 x40 23 x32 24 x26 25 x12 26 x32 27 x4 28 x1 29 x8 31 x2 32 x2 33 x2 30 x2...
- Page 4 STEP 1 21 x 8pcs 22 x 8pcs 23 x 6pcs 23 x 6pcs 22 x 8pcs 21 x 8pcs arrowhead on cam points toward to the hole on the panel edge. STEP 2 26 x 4pcs 30 x 2pcs 26 x 4pcs 30 x 2pcs...
- Page 5 STEP 3 21 x 2pcs 24 x 8pcs 22 x 2pcs 23 x 8 pcs 23 x 8 pcs 22 x 2pcs 21 x 2pcs 24 x 8pcs STEP 4...
- Page 6 STEP 5 24 x 8pcs 21 x 2pcs 22 x 2pcs 23 x 10 pcs 24 x 8pcs 23 x 10 pcs 22 x 2pcs 21 x 2pcs 29 x 8 pcs 29 x 8 pcs STEP 6 21 x 8pcs 23 x 8pcs 22 x 8pcs 23 x 8pcs...
- Page 7 STEP 7 21 x 12pcs 21 x 12pcs 22 x 12pcs 22 x 12pcs arrowhead on cam points toward to the hole on the panel edge. STEP 8...
- Page 8 STEP 9 25 x 4pcs 21 x 8pcs 21 x 4pcs 22 x 8pcs 22 x 4pcs 25 x 8pcs arrowhead on cam points toward to the hole on the panel edge. STEP 10 26 x24pcs 25 x4pcs 27 x4pcs 26 x24pcs 25 x4pcs...
- Page 9 STEP 11 25 x8pcs 25 x8 STEP 12 26 x 4pcs 26 x 4pcs...
- Page 10 NOTE: For gyprock walls ensure you locate the studs, or use appropriate to the wall. (also see Step 14) Use a screw driver to fasten the screws (Part 24) into the wall.
- Page 11 Use a screw driver to fasten the screws (Part 33) into the bracket.
- Page 12 Drawer Front Alignment Drawer front panel If the drawer front panel is NOT level after being assembled, then... Drawer front panel Loosen the screw Adjust the slide up or down Loosen the screws on the left and right hand side, then move the drawer slide up or down, untill the drawer fronts are even/level, then tighten the screws Drawer front panel...
- Page 13 COPY OF YOUR PURCHASE SLIP/RECEIPT MODEL NUMBER OF THE UNIT PURCHASED DESCRIPTION/PART NUMBER OF THE MISSING OR FAULTY PART QUANTITY OF THE PARTS NEEDED If for whatever reason you cannot contact the store, please contact Tauris direct at http://www.rvm.com.au/contact. Product of: RVM Australia...
- Page 14 You are also en tled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Tauris 2. Subject to Clause 1, the Seller warrants that branded products will be free of manufacturing defects and will perform to the Seller’s specifica ons subject to the following...
- Page 15 7. The seller will examine any returned Products and if the Seller determines that there is an apparent defect through no fault of the Owner, the Seller will: a.) Make note of the Owner’s contact details including the Owner’s telephone number which the owner can be contacted during business hours, postal address and e-mail address.