Advertisement
Quick Links
www.rvm.com.au
- Please follow these assembly instructions as it will save you time, make
assembly easier and prevent possible damage to your new unit.
- We strongly recommend that the unit is assembled on a soft surface such
as carpet or blanket.
as power tools can strip threads if over tightened.
- Correct assembly is your responsibility.
- When moving this furniture item, always carry the unit. Dragging or
sliding the unit could damage the unit and the floor surface.
Assembly Instruction Manual
MODEL NO.: NOVA1200
130 - 194
Advertisement
Related Manuals for Tauris NOVA1200
Summary of Contents for Tauris NOVA1200
- Page 1 Assembly Instruction Manual MODEL NO.: NOVA1200 www.rvm.com.au 130 - 194 - Please follow these assembly instructions as it will save you time, make assembly easier and prevent possible damage to your new unit. - We strongly recommend that the unit is assembled on a soft surface such as carpet or blanket.
- Page 2 NOTE: PLEASE CHECK YOU HAVE ALL THE CORRECT PARTS LISTED BELOW BEFORE YOU START ASSEMBLING YOUR TV CABINET x18pcs 27 x6pcs 37 x2pcs 39 x2pcs 38 x2pcs 40 x2pcs...
- Page 3 OVERVIEW...
- Page 4 23 x 6pcs 24 x 6pcs 25 x 6pcs 23 x 6 24 x 6 27 x 4pcs 25 x 6 37 x 2pcs 27 x 4 37 x2 arrowhead on cam points toward to the hole on the panel edge.
- Page 5 26 x 6 26 x 6pcs 25 x 6pcs 25 x 6 1. HAND TIGHTEN THREADED BAR(30) INTO THE LEG FITTING FIRST 2. SLIDE CROSS RAIL(8) ONTO THREADED BAR(30) 30 x 4 3. TIGHTEN NUTS WITH THE SPANER PROVIDED(31) 28 x 4 29 x 4 31 x 4...
- Page 6 32 x6 32 x 6pcs ALIGN AND LIGHTLY TIGHTEN ALL 6 SCREWS BEFORE FULLY TIGHTENING ALL SCREWS (TOP DRAWER) 26 x 5pcs 23 x 5pcs 24 x 5pcs 26 x 5pcs 23 x 5pcs arrowhead on cam points toward to the hole on the 24 x 5pcs panel edge.
- Page 7 (BOTTOM DRAWER) 23 x 5pcs 24 x 5pcs 26 x 5pcs 26 x 5pcs 24 x 5pcs 23 x 5pcs arrowhead on cam points toward to the hole on the panel edge.
- Page 8 33 x4pcs 27 x 2pcs 27 x 2pcs...
- Page 9 NOTE: For gyprock walls ensure you locate the studs, or use appropriate to the wall. (also see Step 11) Use a screw driver to fasten the screws (Part 26) into the wall.
- Page 10 Use a screw driver to fasten the screws (Part 40) into the bracket.
- Page 11 Drawer Front Alignment Drawer front panel If the drawer front panel is NOT level after being assembled, then... Drawer front panel Drawer Side Drawer Runner Loosen the screw Adjust the slide up or down Loosen the screws on the left and right hand side, then move the drawer slide up or down, untill the drawer fronts are even/level, then tighten the screws...
- Page 12 COPY OF YOUR PURCHASE SLIP/RECEIPT MODEL NUMBER OF THE UNIT PURCHASED DESCRIPTION/PART NUMBER OF THE MISSING OR FAULTY PART QUANTITY OF THE PARTS NEEDED If for whatever reason you cannot contact the store, please contact Tauris direct at http://www.rvm.com.au/contact. Product of: RVM Australia...
- Page 13 You are also en tled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Tauris 2. Subject to Clause 1, the Seller warrants that branded products will be free of manufacturing defects and will perform to the Seller’s speci ca ons subject to the following...
- Page 14 7. The seller will examine any returned Products and if the Seller determines that there is an apparent defect through no fault of the Owner, the Seller will: a.) Make note of the Owner’s contact details including the Owner’s telephone number which the owner can be contacted during business hours, postal address and e-mail address.