Subscribe to Our Youtube Channel
Related Manuals for CEL-MAR ADA-I9141
Summary of Contents for CEL-MAR ADA-I9141
- Page 1 ADA-I9141 User manual ADA-I9141 USB to RS-485 / RS-422 converter (without galvanic isolation) Copyright © 2001-2024 CEL-MAR sp.j. io_ada-i9141_v3.16_en...
-
Page 2: Table Of Contents
ADA-I9141 Contents 1. GENERAL INFORMATION..................................3 1.1. WARRANTED INFORMATION............................... 3 1.2. GENERAL CONDITIONS FOR SAFE USE............................ 3 1.3. CE LABEL....................................... 3 1.4. ENVIRONMENTAL PRESERVATION............................3 1.5. SERVICE AND MAINTENANCE..............................3 1.6. PACK CONTENTS..................................3 2. PRODUCT INFORMATION..................................3 2.1. PROPERTIES....................................3 2.2. -
Page 3: General Information
1.1. WARRANTED INFORMATION ADA-I9141 converter is covered by a two year warranty on parts and operation from date of sale. In case of being damaged it will be repair or the damaged component will be replace. The warranty does not cover damage caused from improper use, materials consumption or any unauthorized changes. -
Page 4: Description
-Mac: OS X 10.3 to 10.8, OS X 10.9 and other. 3. CONFIGURATION ADA-I9141 converter can be configured for operating in RS485 or RS422 by the use MODE switch (fig.1). Description of setting is shown in the table below. Switch... -
Page 5: Connection To Rs485/Rs422 Bus
4.1.2. CONNECTION TO RS485 2-WIRE BUS Most of RS485 interface devices use two-wire bus for data transmission. You should check the setting of ADA-I9141 to operate on RS485 2-wire bus before connecting to 2-wire network – MODE switch should be set on RS485, then connect the bus wires to terminal TX+, TX- as shown below. -
Page 6: Line Termination
Connect the converter to the computer's USB port and continue following the installation wizard's instructions. 5.1. DRIVERS INSTALLATION IN SYSTEM WINDOWS VIA INTERNET To install drivers for ADA-I9141 in Windows 10, connect the converter to the USB port and wait until the system downloads the latest drivers from the Internet and installs them. - Page 7 ADA-I9141 Select STANDARD Drivers and press [Next] Press [Install]...
- Page 8 ADA-I9141 Press [Next], will be installed Drivers for USB Bus.
- Page 9 ADA-I9141 Press [Install this driver software anyway]. Installation of drivers for USB Bus will start.
- Page 10 ADA-I9141 Press [Install this driver software anyway]. Installation of drivers for Virtual Port will start. Press [Finish]...
- Page 11 ADA-I9141 Press [Finish]. The driver for ADA-I9141 have been installed. This can be checked in “Uninstall or change a program“. Now you can connect ADA-I9141 to computer port.
-
Page 12: Driver Uninstallation
COM port was assigned to converter. After this installation, RS485/422 port of ADA-I9141 converter is available in the system as normal COM port. You have to remember about specified baud rate for communication. -
Page 13: Emergency Driver Uninstallation
ADA-I9141 f/ select from the list Windows Driver Package – CEL-MAR ADA – USB Serial Converter g/ press [Uninstall/Change], driver converter of USB Bus will be uninstalled, h/ after uninstallation reboot the computer. 6.2. EMERGENCY DRIVER UNINSTALLATION If there are problems with property operation of drivers or converter, and or on computer was installed drivers other devices this type, an operating system should be cleaned (files&entries in system registers) by the use of special software. -
Page 14: Using
After property connection according to section above you can start using the converter. During data transmission LEDs should blink and they indicate appropriately: Description Rx (yellow) Data reception via ADA-I9141 converter from RS485/RS422 port. Tx (red) Data transmission from ADA-I9141 converter via RS485/RS422 port. 7.1. BAUD RATE SELECTION FOR PROFIBUS COM PORT For setting correct Profibus baud rate (after installation “Virtual Port”... -
Page 15: Specification
ADA-I9141 8. SPECIFICATION TECHNICAL DATA Transmission Parameters Interface RS-485/422 Connector A-type Mail Screw terminal block, max. wire Ø 1mm Line length up to 5m 1200 m (depend on baud rate) Max. number of connected devices 32 / 2 Twisted cable 1-pair, 2- pair or 4-pair,... - Page 16 We hope that, this user manual helped in connecting and starting ADA-I9141 converter. We also wish to inform You, that CEL-MAR Company is a manufacturer of the widest selection of data communications products in the world in applications such as: data transmission converters in RS232, RS485, RS422, USB, Current Loop, Fibre-Optic and Ethernet Converters and many others.
Need help?
Do you have a question about the ADA-I9141 and is the answer not in the manual?
Questions and answers