Subscribe to Our Youtube Channel
Related Manuals for Dahua IPCHDBW5541R1PAS
Summary of Contents for Dahua IPCHDBW5541R1PAS
- Page 1 Dome Network Camera Quick Start Guide ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.2...
-
Page 2: Foreword
Quick Start Guide Foreword General This manual introduces the functions, installation, and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury. - Page 3 Quick Start Guide respective owners. Please visit our website, contact the supplier or customer service if any problems occur while using the device. If there is any uncertainty or controversy, we reserve the right of final explanation. ...
-
Page 4: Important Safeguards And Warnings
Quick Start Guide Important Safeguards and Warnings Electrical Safety All installation and operation shall conform to your local electrical safety codes. The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited Power Source requirement according to IEC60950-1. Note that the power supply requirement is subject to the device label. - Page 5 Quick Start Guide It is recommended to ground the device to enhance reliability. Do not touch the image sensor (CMOS) directly. Dust and dirt can be removed with air blower, or you can wipe the lens gently with soft cloth that is moistened with alcohol. You can clean the device body with soft dry cloth, and for stubborn stains, use the cloth with mild ...
-
Page 6: Table Of Contents
Quick Start Guide Table of Contents Foreword ................................I Important Safeguards and Warnings ......................III 1 Introduction ..............................1 Cables ......................................1 Connecting Alarm Input/output ............................2 2 Network Configuration ..........................4 Initializing Device ..................................4 Modifying Device IP Address ..............................5 Logging in to Webpage ................................ -
Page 7: Introduction
Quick Start Guide Introduction Cables Device ports might vary with different models, and the actual product shall prevail. Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage. For the detailed operation, see the FAQ Manual. Cables For more information about device ports, see Table 1-1. -
Page 8: Connecting Alarm Input/Output
Quick Start Guide Includes alarm signal input and output ports, and Alarm I/O the number of I/O ports might vary on different devices. For details, see Table 1-2. For more information about I/O port, see Table 1-2. Table 1-2 Alarm information Port Port Name Function... - Page 9 Quick Start Guide Mode A Mode B Log in to webpage, and configure alarm input and alarm output in alarm setting. The alarm input on the webpage is corresponding to the alarm input end of the I/O port. There will be high-level and low-level alarm signal generated by the alarm input device when alarm occurs.
-
Page 10: Network Configuration
Quick Start Guide Network Configuration Device initialization and IP address setting can be finished with the "ConfigTool" or on webpage. For more information, see the Web Operation Manual. Device initialization is available on select models, and it is required at first use or after the device ... -
Page 11: Modifying Device Ip Address
Quick Start Guide Select the devices that need initialization, and then click Initialize. Password setting Set and confirm the password of the devices, then enter a valid email address, and then click Next. The final setting page is displayed. Password can be modified or reset in System Settings. Select the options according to your needs, and then click OK. -
Page 12: Logging In To Webpage
Quick Start Guide Modify IP Address Select Static mode, and then enter start IP, subnet mask, and gateway. IP addresses of multiple devices will be set to the same if you select the Same IP check box. If DHCP server is available in the network, devices will automatically obtain IP ... - Page 13 Quick Start Guide Main page...
-
Page 14: Installation
Quick Start Guide Installation Packing List The tool required for the installation such as electric drill is not provided in the packing. The operation manual and related tool are contained in the disk or the QR code, and the actual ... -
Page 15: Attaching Device
Quick Start Guide You can press the reset button for 10 seconds to reset the device as needed, which will restore the device to factory settings. Figure 3-2 Install the SD card 3.2.2 Attaching Device Make sure that the mounting surface is strong enough to hold at least 3 times of the weight of the device and bracket. - Page 16 Quick Start Guide Figure 3-4 Cable going through the side cable tray...
-
Page 17: Optional) Installing Waterproof Connector
Quick Start Guide 3.2.3 (Optional) Installing Waterproof Connector This section is only necessary if a waterproof connector is included in your package, and the device is installed outdoors. Figure 3-5 Install the waterproof connector... -
Page 18: Adjusting Lens Angle
Quick Start Guide 3.2.4 Adjusting Lens Angle Figure 3-6 Adjust the lens angle... - Page 19 Quick Start Guide...
Need help?
Do you have a question about the IPCHDBW5541R1PAS and is the answer not in the manual?
Questions and answers