ENGLISH COLLEGAMEWNTO-01 Interactive Links The document contains INTERACTIVE LINKS for faster and more efficient consultation. App CallMe Set Version: 1.2.0-12 or higher INDEX 1. THE CALLME SET APP .............................27 2. CREATE A NEW ACCOUNT OR USE A SAVED ACCOUNT ................28 2.1.
1. THE CALLME SET APP Wait for the following screen to open: This booklet describes the use of the CallMe Set app for configuring the call forwarding function on the following call sender devices: • 1760/31A, 1760/32A and 1760/33A • 1760/15, 1760/16, 1760/18 and 1760/19 Download the application from the Play Store (Android).
2. CREATE A NEW ACCOUNT 2.1. CREATE NEW ACCOUNT OR USE A SAVED ACCOUNT Users do not normally have a Urmet Cloud account. From this screen, it is therefore possible to create one To be able to use the App you need to create an account - a necessary condition to be able to use the service.
In this case, too, the user will be automatically referred to the Home Page. 2.2. USE A SAVED ACCOUNT (LOGIN) Note that up to four smartphones can be If, however, the user already has a sip.urmet.com registered on one account while the same account (e.g.
4. DEVICE CONFIGURATION The meaning of the buttons on the Homepage is as follows: To configure your device, firstly create an account 1. Press the “Device configuration” button to (or log in using an existing account), as explained in configure the call forwarding function on a device. the “CREATE A NEW ACCOUNT OR USE A SAVED 2.
Page 7
VIDEO DOOR PHONE 1760/31A -/32A -/33A Press the “1760/31A, 32A, 33A’ buttonon the app, the following screen appears: In the settings menu, select the “Advanced Settings” item. After accessing the parameter, press on the “Continue” button on your smartphone. On the video door phone, press the button to access the Top Page, then press the button to access the setting page.
Page 8
After a few seconds the video door phone will switch to configuration mode and a QR code will appear on the display. After the video door phone displays the QR code, press the “Continue” button on your smartphone.. Then activate the WiFi on the smartphone and access the “CALLFW_XXYYZZ”...
Page 9
connected via a modem/router to the Internet. Connection to the home LAN must be over Wi-Fi. After setting the intervals (the operation caneven not be done) press “Continue” and yes will go to the “IP routing options” page. It is essential to select from the dropdown menu the (condominium) network to connect to.
Page 10
Pressing the “Save” key allows the device to store the configuration. Enter the following values in the empty fields: IP Address, Subnet Mask, Default Gateway and DNS (e.g.: 8.8.8.8) then press “Continue”. 19. The following screen appears on the smartphone. Now, it will be possible to choose the VIDEO quality (Default value: LOW) then press “Continue”.
Page 11
The device will connect using the newly saved 2. On the video door phone, press the button configuration and the following screen will be twice to display the Homepage, then press the displayed. buttons and select the parameter setup icon 3.
Page 12
8. Press the “Scan” button to launch the QR-Code reader application. Scan the QR code shown on the display of the video door phone. Scan the QR-Code to registered the device on the server. The following screen can be used to choose the name of the device (name that will be displayed as ‘Caller’...
Page 13
Tick ”Advanced” only for access to special settings, e.g. access to hidden networks After selecting the network, enter the relevant network Password and press “Continue”. It is optionally possible to identify up to two time intervals during which the Wi-Fi will be automatically switched off daily (e.g.
Page 14
It is preferable to choose the default configuration A LOW video quality allows for operation options. Should this be not possible, if the network notwithstanding the Internet connection speed. to which you wish to connect requires a fixed IP Unless you are absolutely sure to have a high address, select the option “Advanced”...
4.1. DEVICE TEST By pressing Yes , the device’s Firmware can be step 7 updated, skip to in the chapter “Firmware After completing the configuration of the device run a Update”. test to check that the device is working properly. By pressing No, the screen closes without The test phase is the same for all video door phones.
Page 16
will no longer be possible to switch to displaying the next door unit or camera and the “Cameras” button will be replaced by the “Mute” button, which can be used to deactivate the audio channel. If the functions are activated correctly, press the “Terminate”...
Page 17
7. The following page will appear: The Quality icon shows the quality of the conversation based on the Internet connection of your smartphone: High Medium Press the button to deactivate the hands-free function and pass the conversation to the capsule. Press again to reactivate the hands-free function.
8. Once the test is done, the user’s smartphone must Select the button for the device to be replaced: — 1760/31A, 32A, 33A be paired with the device to activate the function (see the “Activating the Call Forwarding Service” — 1760/15, 16, 18, 19 CallMe app configuration booklet).
6. FIRMWARE UPGRADE The firmware can be updated for the following devices: Video door phone 1760/31A - /32A - /33A — The firmware of some devices can be updated over the Video door phone 1760/15 - /16 - /18 - /19 —...
Page 20
7. The following screen appears on the smartphone: 10. Press “Yes” to start the update. The following page will appear: An alert screen will appear to indicate that there are no further available updates if the latest firmware version is already installed on the video door phone. 8.
Page 21
VIDEO DOOR PHONE 1760/15 - /16 -/18 - /19 WARNING! If the video door phone is configured in “Apartment block” mode, it is not possible to update the firmware via the CallMe Set app. 1. Select the “1760/15,16,18,19”. button here. The following screen will appear: The firmware upgrade is characterised by an orange band at the top of the screen.
Page 22
9. The “Status” parameter will change to “On” mode 12. Press the “Start” button to continue the procedure. after a few seconds on the display of the video door phone. 10. Now on the smartphone the following page will appear: 13.
7. USER ACCOUNT On the Homepage, press the “User Account” button. The firmware upgrade is characterised by an orange band at the top of the screen. 16. The app will display the following screen when the The following screen will appear: installation is complete.
9. EXIT — Pressing the “Change password” button is possible change your password. Press the “Exit” button on the Homepage to exit the CallMe Set app. — Pressing the “Logout” button you can make the Logout with the account connected to the CallMe Set app.
Need help?
Do you have a question about the 1083 and is the answer not in the manual?
Questions and answers