Noble I-E Installation, Operation And Service Manual
  1. Manuals
  2. Brands
  3. Noble Manuals
  4. Dishwasher
  5. I-E
  6. Installation, operation and service manual

Noble I-E Installation, Operation And Service Manual

Door-type dishmachines
Hide thumbs Also See for I-E:
Table of Contents

Advertisement

Quick Links

Download this manual
NOBLE DOOR-TYPE DISHMACHINES
INSTALLATION, OPERATION,
AND SERVICE MANUAL
Noble I-E
Noble I-E-FL
Noble I-E-LTH
Noble I HH
Noble I-E Series/I HH Manual • 07610-004-25-06-R

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the I-E and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Noble I-E

Summary of Contents for Noble I-E

  • Page 1 NOBLE DOOR-TYPE DISHMACHINES INSTALLATION, OPERATION, AND SERVICE MANUAL Noble I-E Noble I-E-FL Noble I-E-LTH Noble I HH Noble I-E Series/I HH Manual • 07610-004-25-06-R...
  • Page 2 Revised lower control box decal P/N. Updated in-line fuse assembly P/N. Added 230 V 2-8-24 23-2258 relay and contactor to I-E/I-E-FL/I HH Control Box section. Added 230 V solenoid valve to I-E/I- 23-2273 E-FL/I HH Plumbing section and updated P/N for the 115 V solenoid valve. Revised P/N for the...
  • Page 3 NOMENCLATURE Noble I-E Door-type dishmachine; chemical-sanitizing, single-rack. Noble I-E-FL Door-type dishmachine; chemical-sanitizing, single-rack, front-loading. Noble I-E-LTH Door-type dishmachine; chemical-sanitizing, single-rack, with booster heater. Noble I HH Door-type dishmachine; chemical-sanitizing, single-rack with high hood. The manufacturer provides technical support for all of the dishmachines detailed in this manual.

  • Page 4: Table Of Contents

    TABLE OF CONTENTS SPECIFICATIONS I-E Dimensions ...........................1 I-E-FL Dimensions ........................2 I-E-LTH Dimensions ........................3 I-HH Dimensions .........................4 Table Installation .........................5 Operating Capacities ........................6 Electrical Requirements ......................7 INSTALLATION Installation Instructions ....................... 8 Inspection......................... 8 Unpacking ........................8 Leveling..........................8 Facility Hot Water Heater ....................8 Plumbing ..........................
  • Page 5 I-E-LTH Booster Tank .......................53 Frame ............................55 Miscellaneous Parts .........................56 SCHEMATICS I-E/I-HH 115 V, 60 Hz, 1-Phase ....................57 I-E/I-HH 230 V, 60 Hz, 1-Phase ....................58 I-E-LTH 208/230 V, 60 Hz, 1/3 Phase ..................59 I-E-FL 115 V, 60 Hz, 1-Phase ....................60...
  • Page 6 GUIDES GUIDES SYMBOLS WARNING - Risk of Damage to Equipment CAUTION - Risk of Electrical Shock - Caustic Chemicals - Reference Data Plate - Lockout Electrical Power - Important Note NOTICE - Instructions Hyperlink ABBREVIATIONS & ACRONYMS ANSI - American National Standards Institute GHT - Garden Hose Thread GPG - Grains per Gallon GPM - Gallons per Minute...

  • Page 7: Specifications

    I-E DIMENSIONS SPECIFICATIONS 4 in (102 mm) LEGEND MINIMUM A - Electrical Connection (1 1/8” Hole) B - Water Inlet (1/2” NPT) 1 (25 mm) C - Drain Connection (2” NPT) D - Chemical Connection (7/8” Hole) 13 1/4 (337 mm) All dimensions from the floor can be increased 1 1/8”...

  • Page 8: I-E-Fl Dimensions

    I-E-FL DIMENSIONS SPECIFICATIONS [102 mm] LEGEND MINIMUM A - Electrical Connection (1 1/8” Hole) B - Water Inlet (1/2” NPT) C - Drain Connection (2” NPT) D - Chemical Connection (7/8” Hole) [25 mm] 13 1/4 All dimensions from the floor can be increased [337 mm] 1 1/8”...

  • Page 9: I-E-Lth Dimensions

    I-E-LTH DIMENSIONS SPECIFICATIONS 4 in (102 mm) LEGEND MINIMUM A - Electrical Connection (1 1/8” Hole) B - Water Inlet (3/4” NPT) 1 (25 mm) C - Drain Connection (2” NPT) D - Chemical Connection (7/8” Hole) All dimensions from the floor can be increased 13 1/4 (337 mm) 1 1/8”...

  • Page 10: I-Hh Dimensions

    I-HH DIMENSIONS SPECIFICATIONS LEGEND (102 mm) MINIMUM A - Electrical Connection (1 1/8” Hole) B - Water Inlet (1/2” NPT) C - Drain Connection (2” NPT) 1 (25 mm) D - Chemical Connection (7/8” Hole) All dimensions from the floor can be increased 13 1/4 (337 mm) 1 1/8”...
  • Page 11 TABLE INSTALLATION SPECIFICATIONS CORNER INSTALLATION 4 (102 mm) MIN ALIGN WITH TABLE - DISTANCE CAN VARY I-E Series False Panel Kit 06401-005-14-17 False Panel Only 8 1/4 4 (102 mm) MIN (210 mm) 05700-005-14-73 20 1/2” ALIGN WITH TABLE -...

  • Page 12: Operating Capacities

    OPERATING CAPACITIES SPECIFICATIONS Model Designation: I-E/I-E-FL I-E-LTH I-HH Operating Capacity: Racks per Hour Dishes per Hour Glasses per Hour 1404 1404 1404 Tank Capacity (Gallons): Wash Tank 1.02 (40.2 GPH) 1.02 (40.2 GPH) 1.61 (62.8 GPH) Electrical Loads (as applicable):...

  • Page 13: Electrical Requirements

    All electrical ratings provided in this manual are for reference only. Always refer to the machine data plate to get exact electrical information for this machine. All electrical work performed on machines should be done in accordance with applicable local, state, territorial, and national codes. authorized service agents. Available Electrical Characteristics: I-E/I-E-FL/I-HH I-E-LTH Electrical Characteristics Electrical Characteristics VOLTS...

  • Page 14: Installation

    INSTRUCTIONS INSTALLATION INSPECTION Before installing the machine, check the packaging and machine for damage. If the packaging is damaged, the machine might also be damaged. If there is damage to both the packaging and machine, do not throw away the packaging. The machine has been inspected and packed at the factory and is expected to arrive to you in new, undamaged Do not throw away the condition.

  • Page 15: Water Supply Connections

    INSTRUCTIONS INSTALLATION WATER SUPPLY If water hardness tests higher than 3 GPG, install the Scaltrol Water Treatment system (see the Plumbing Options page) into the water line before the machine’s incoming CONNECTIONS: water connection point. A water shut-off valve should be installed to allow access for WATER HARDNESS service.

  • Page 16: Electrical Power Connections

    INSTRUCTIONS INSTALLATION ELECTRICAL POWER Electrical and grounding conductors must comply with the applicable portions of the National Electric Code ANSI/NFPA 70 (latest edition) and/or other electrical codes. CONNECTIONS Refer to the machine data plate for machine operating requirements, machine voltage, total amperage, and serial number.

  • Page 17: Voltage Check

    INSTRUCTIONS INSTALLATION VOLTAGE CHECK 1. Ensure power switch is in the OFF position and apply power to the machine. 2. Check the incoming power at terminal block and ensure it corresponds to voltage problem. CAUTION! Do not run the machine if voltage is too high or too low (refer to applicable electrical codes).

  • Page 18: Heater Contactor Wires (Lth Only)

    INSTRUCTIONS INSTALLATION PRIMING CHEMICAL • FEEDER PUMPS WARNING WARNING! Some of the chemicals used in • dishwashing might cause chemical burns if they come in contact with skin. Wear protective gear when handling these chemicals. If any contact with skin occurs, immediately follow the treatment 4.

  • Page 19: Cycle Timer Instructions

    MODEL EXIT SELECT MODEL 2. Select correct model using ARROW buttons under STEP DURATION. 3. Press SAVE/EXIT. Model SELECT CYCLE STEP TO ADJUST PRESS SAVE TO EXIT CONS I-E (Use for I-E, RINSE CYCLE PUMP DRAIN FILL SANI DETER SPARE...
  • Page 20 CYCLE TIMER INSTRUCTIONS INSTALLATION CHANGING CYCLE 1. Press button for step being changed. The LED for that step will come on. STEP TIMES SELECT CYCLE STEP TO ADJUST PRESS SAVE TO EXIT RINSE CYCLE PUMP DRAIN FILL SANI DETER SPARE START DURATION DISH...
  • Page 21 CYCLE TIMER INSTRUCTIONS INSTALLATION RESETTING TO 1. Press and hold CYCLE COUNT button and DOWN ARROW button (under STEP DURATION) simultaneously for 3–4 seconds. FACTORY DEFAULTS SELECT CYCLE STEP TO ADJUST PRESS SAVE TO EXIT RINSE CYCLE PUMP DRAIN FILL SANI DETER SPARE...
  • Page 22 CYCLE TIMER INSTRUCTIONS INSTALLATION PLANT TEST MODE 1. Press and hold CYCLE COUNT button and DOWN ARROW button (under STEP START TIME) simultaneously for 3–4 seconds. SELECT CYCLE STEP TO ADJUST PRESS SAVE TO EXIT RINSE CYCLE PUMP DRAIN FILL SANI DETER SPARE...

  • Page 23: Operation

    OPERATING INSTRUCTIONS OPERATION PREPARATION Before operating the machine 1. The sump strainer and pan strainer are in place and clean. 2. The drain stopper is installed. 3. The wash/rinse arms (top and bottom) are installed and secure. POWER UP To place the machine FILLING THE hold OFF/ON/FILL switch in FILL position for approximately 8–10 seconds.

  • Page 24: First Rack

    Once the cycle is complete, open door (again careful of the dripping hot water) and remove rack of clean ware. Replace with a rack of soiled ware and close door. The On the I-E-LTH, choose Normal, Medium, or Heavy next cycle starts automatically.

  • Page 25: Shutdown & Cleaning

    OPERATING INSTRUCTIONS OPERATION SHUTDOWN & 1. Turn machine off by flipping OFF/ON/FILL switch to OFF position. CLEANING 2. Open door. 3. Remove drain stopper and allow tub to drain. WARNING WARNING! Wash tank water could be hot. 4. Remove sump strainer and pan strainer. 5.
  • Page 26 OPERATING INSTRUCTIONS OPERATION SHUTDOWN & 8. Verify nozzles and arms are free from obstruction. If clogged, remove end-caps, clean nozzles with a brush, and flush with fresh water. CLEANING 9. Replace end-caps and ensure they are tight. 10. Spray or wipe-out interior of machine. 11.

  • Page 27: Deliming

    DELIMING INSTRUCTIONS OPERATION DELIMING 1. Follow Filling the Wash Tub section of this manual. 2. Add deliming solution per chemical supplier’s instructions. 3. Close door. 4. Flip NORMAL/DELIME switch on the back of the control box to DELIME. DELIME NORMAL 5.

  • Page 28: Detergent Control

    DETERGENT CONTROL OPERATION DETERGENT Detergent use and water hardness are two factors that greatly contribute to the CONTROL • Hard water greatly affects the performance of the machine, causing the amount of detergent required for washing to increase. If the machine is installed in an area with hard water, the manufacturer recommends the installation of water treatment equipment.

  • Page 29: Preventative Maintenance

    PREVENTATIVE MAINTENANCE MAINTENANCE PREVENTATIVE discussed in this manual be performed only by QUALIFIED SERVICE PERSONNEL. MAINTENANCE Performing maintenance on your machine may void your warranty, lead to larger problems, or even cause harm to the operator. So if you have a question or concern, do not hesitate to contact a QUALIFIED SERVICE AGENCY.

  • Page 30: Troubleshooting

    TROUBLESHOOTING TROUBLESHOOTING OBSERVATION POSSIBLE CAUSE REMEDY Machine will not run, 1. Service disconnect switch 1. Turn disconnect on. no voltage at wash relay off or faulty. terminals L1 and T1. 2. Branch circuit breaker 2. Reset or replace. tripped/fuse blown. 3.
  • Page 31 TROUBLESHOOTING TROUBLESHOOTING OBSERVATION POSSIBLE CAUSE REMEDY 1. Clogged or obstructed 1. Remove and clean the rinse arms. rinse is weak. rinse arms. 2. Low incoming water pressure. 3. Y-strainer is clogged. 3. Clean out the Y-strainer. Doors will not close 1.

  • Page 32: Parts

    I-E/I-E-FL/I-HH CONTROL BOX PARTS TO DRAIN SOLENOID (SEE SCHEMATIC) ITEM DESCRIPTION PART NUMBER Switch, Prime 05930-011-49-54 Light, Red 05945-504-07-18 Light, Green 05954-504-08-18 Switch, Delime 05930-301-21-18 Cycle Counter 05990-111-35-38 Screw, 4-40 x 1/4" Phillips Pan Head with Washer 05305-002-32-38 07610-004-25-06-R...
  • Page 33 I-E/I-E-FL/I-HH CONTROL BOX PARTS ITEM DESCRIPTION PART NUMBER Terminal Block 05940-500-09-61 Contactor, 115 V, 30 A 05945-109-05-69 Contactor, 240 V, 30 A 05945-002-74-20 Terminal Board 05940-021-94-85 Lug, Ground 05940-200-76-00 Spacer, Terminal Block 05700-011-40-05 Lock Nut, 10-24 SS Hex with Nylon Insert...

  • Page 34: I-E-Lth Control Box

    I-E-LTH CONTROL BOX PARTS ITEM DESCRIPTION PART NUMBER I-E-LTH Control Box Complete Assembly 05700-004-49-01 Box, Control Assembly 05700-004-49-02 Bracket, Terminal Block 05700-004-51-59 Bracket, Pressure Switch 05700-004-08-99 Bracket, Timer Mounting 05700-004-08-77 Chemical Feeder Pump Assembly, 36 RPM 05700-003-78-74 Chemical Feeder Pump Assembly, 14 RPM...
  • Page 35 I-E-LTH CONTROL BOX PARTS ITEM DESCRIPTION PART NUMBER Thermostat, Electric (Dual) 06685-004-17-27 Probe, Thermistor 4” 06685-004-17-26 Terminal Board 05940-021-94-85 Terminal Block, 3-Pole 05940-011-48-27 Contactor, 30 A 05945-002-74-20 Counter, Plastic 05990-111-47-42 Relay, Top Mount 05945-111-47-51 Lug, Ground 05940-200-76-00 P-clamp, 1/4" ID...

  • Page 36: Chemical Feeder Pumps, 115 V

    CHEMICAL FEEDER PUMPS, 115 V PARTS ITEM DESCRIPTION PART NUMBER Pump Housing 04320-111-37-09 Screw, 8-32 x 3/8" Phillips 05305-011-37-07 Roller, Plastic 04320-002-82-28 Pump Cover 04320-111-37-08 Screw, 6-32 x 3/4" Phillips 05305-011-37-05 Screw, 8-32 x 1/2" Phillips 05305-011-37-06 Tube, Squeeze, 8" 05700-003-22-89 Motor, 14 RPM 04320-111-35-13...

  • Page 37: Chemical Feeder Pumps, 208/230 V

    CHEMICAL FEEDER PUMPS, 208/230 V PARTS ITEM DESCRIPTION PART NUMBER Pump Housing 04320-111-37-09 Screw, 8-32 x 3/8" Phillips 05305-011-37-07 Roller, Plastic 04320-002-82-28 Pump Cover 04320-111-37-08 Screw, 6-32 x 3/4" Phillips 05305-011-37-05 Screw, 8-32 x 1/2" Phillips 05305-011-37-06 Tube, Squeeze, 8" 05700-003-22-89 Motor, 14 RPM 04320-111-47-46...

  • Page 38: I-E/I-E-Lth Hood

    I-E/I-E-LTH HOOD PARTS NOTICE Machines with serial numbers before 21F394964 have a different hood. See earlier manual. 07610-004-25-06-R...
  • Page 39 I-E/I-E-LTH HOOD PARTS ITEM DESCRIPTION PART NUMBER Control Box Assembly, XL-E 115 V 05700-004-78-13 Control Box Assembly, XL-E 208/230 V 05700-004-16-66 Control Box Assembly, XL-E-LTH 05700-004-49-01 Bolt, 1/4-20 x 1/2" 05305-274-02-00 Guide, Hood 05700-004-90-99 Screw, 10-32 x 1/2” 05305-011-44-51 Support, Hood...

  • Page 40: I-E-Fl Hood

    I-E-FL HOOD PARTS 07610-004-25-06-R...
  • Page 41 I-E-FL HOOD PARTS ITEM DESCRIPTION PART NUMBER Control Box Assembly, I-E-FL 05700-004-78-13 Screw, 1/4-20 x 1/2" Button Head Hex 05305-004-62-33 Cap, Snap-in 05340-004-77-82 Bracket, Upright Upper 05700-004-76-36 Upright, Left 05700-004-81-54 Bracket, Upright Lower 05700-004-76-35 Guide Block, Stop 09330-004-77-73 Mount, Upper Panel...

  • Page 42: I-Hh Hood

    I-HH HOOD PARTS 07610-004-25-06-R...
  • Page 43 I-HH HOOD PARTS ITEM DESCRIPTION PART NUMBER Control Box Assembly, 115 V 05700-004-25-41 Control Box Assembly, 230 V 05700-004-30-24 Locknut, 1/4-20 with Nylon Insert 05310-374-01-00 Hood Support 05700-004-13-45 Bolt, 1/4-20 x 1/2” 05305-274-02-00 Washer, SS 1/4” 05311-174-01-00 Bracket, Cantilever Support 09515-003-15-64 Wear Button 05700-011-88-01...

  • Page 44: I-E/I-E-Fl/I-Hh Plumbing

    I-E SERIES/I-HH PLUMBING PARTS Complete Plumbing Assembly 05700-004-21-11 ITEM DESCRIPTION PART NUMBER Bushing, 3/4" to 1/2" Brass 04730-002-56-27 Elbow, 90-degree, 1/2" Brass 04730-206-08-00 Nipple, 1/2" x 3" Brass 04730-004-20-10 Solenoid Valve, 1/2", 115 V 04810-003-71-55 Solenoid Valve, 1/2", 230 V 04810-003-71-56 Y-strainer, 1/2"...

  • Page 45: I-E-Lth Plumbing

    I-E-LTH PLUMBING PARTS Complete Plumbing Assembly 05700-004-49-05 ITEM DESCRIPTION PART NUMBER Y-strainer, 3/4" Brass 04730-717-02-06 Nipple, 3/4" x 4 1/2" Brass 04730-004-04-53 Solenoid Valve, 3/4" 04810-100-03-18 Nipple, 3/4" x 1 3/8" Brass 04730-207-34-00 Elbow, 90-degree, 3/4" Brass 04730-206-13-00 Nipple, 3/4" x 3" Brass...

  • Page 46: Plumbing Options

    PLUMBING OPTIONS PARTS SHOCK ABSORBER (WATER ARRESTOR) OPTION Water Arrestor, 1/2” 06685-100-05-00 I-E Series/I-HH I-E-LTH Tee, 1/2” x 1/2” x 1/2” Tee, 3/4” x 3/4” x 1/2” 04730-211-27-00 04730-211-06-00 Nipple, 1/2” NPT, Close, Brass Nipple, 3/4” NPT, Close, Brass 04730-207-15-00...

  • Page 47: I-E/I-E-Lth Door

    I-E/I-E-LTH DOOR PARTS NOTICE Machines with serial numbers before 21F394964 have a different 24, 18 door. See earlier manual. 10, 11, 12 15, 16 23, 18 17, 18 21, 25 19, 11, 12 07610-004-25-06-R...
  • Page 48 I-E/I-E-LTH DOOR PARTS ITEM DESCRIPTION PART NUMBER Complete Cantilever Arm Assembly (items 1–5) 05700-004-85-10 Cantilever Arm Only 05700-001-21-00 Spring Pin, 1/4" x 1 1/8" 05315-407-06-00 Yoke Assembly 05700-000-75-77 Cotter Pin 05315-207-01-00 Yoke 05700-000-75-78 Clevis Pin, 5/16” x 1 3/8” 05315-700-01-00...

  • Page 49: I-E-Fl Door

    I-E-FL DOOR PARTS Complete Door Assembly 05700-004-74-43 SECTION A-A 07610-004-25-06-R...
  • Page 50 I-E-FL DOOR PARTS ITEM DESCRIPTION PART NUMBER Panel, Door Outer 05700-004-78-22 Panel, Door Inner 05700-004-77-68 Bracket, Door Right 05700-004-74-35 Bracket, Door Left 05700-004-74-36 Guide, Rack, Right 05700-004-72-81 Guide, Rack, Left 05700-004-72-82 Door Handle Support 05700-004-17-42 Door Handle 05700-003-26-62 Spring, Door Torsion, Right...

  • Page 51: I-Hh Door

    I-HH DOOR PARTS 07610-004-25-06-R...
  • Page 52 I-HH DOOR PARTS ITEM DESCRIPTION PART NUMBER Door, Front Outer 05700-004-14-21 Door, Left Outer 05700-004-14-19 Door, Right Outer 05700-004-14-17 Bracket, Door Connecting 05700-004-14-23 Handle, Door Front 05700-004-14-30 Plug, Cantilever 05340-011-35-00 Washer, 1/4-20 ID 05311-174-01-00 05310-374-02-00 Bolt, 1/4-20 x 1/2" Long 05305-274-02-00 Door Stop 05700-002-00-84...

  • Page 53: Wash Arms

    WASH ARMS PARTS Wash Arm Assembly 05700-003-59-35 2 per Machine ITEM DESCRIPTION PART NUMBER Bearing Assembly 05700-021-35-97 O-ring, 117-S70 Silicon 05330-002-60-69 Wash Arm End-cap 05700-011-35-92 Wash Arm 05700-003-57-70 07610-004-25-06-R...

  • Page 54: Wash Manifold

    WASH MANIFOLD PARTS ITEM DESCRIPTION PART NUMBER Bolt, 3/8-16 x 3/8" SS 05306-011-36-95 Casting, Upper Wash Manifold 05700-031-34-82 3/8" Lockwasher, SS 05311-276-01-00 3/8" Hex Nut, SS 05310-276-01-00 Bolt, 3/8-16 x 1 1/4" SS 05305-276-10-00 Lower Wash Manifold 05700-003-78-40 Gasket, Wash Manifold 05700-111-35-03 3/8"...

  • Page 55: Tub

    PARTS ITEM DESCRIPTION PART NUMBER Rack Guide Assembly, I-E Series/I-HH 05700-031-36-76 Rack Guide Assembly, I-E-FL 05700-004-84-25 Bulkhead Fitting, 1/2” 04730-011-45-21 Clamp, Nylon 04730-011-39-01 Lock Nut, 10-24 05310-373-01-00 Wash Arm Assembly 05700-003-59-35 Bolt, 1/4-20 x 1/2” 05305-274-02-00 Lock Nut, 1/4-20 05310-374-01-00 Bolt, 1/4-20 x 1 1/8”...

  • Page 56: Wash Sump

    WASH SUMP PARTS ITEM DESCRIPTION PART NUMBER Pump & Motor Assembly See Pump & Motor page. Pump Drain Hose 05700-004-08-52 Clamp, 7/16” to 25/32” 04730-011-36-05 Sump Weldment 05700-003-78-41 Sump Gasket 05330-003-78-31 Lock Nut, 1/4-20 05310-374-01-00 Drain Solenoid, 115 V 04810-200-11-00 Drain Solenoid, 208/230 V 04810-111-87-74 Drain Link...

  • Page 57: Spillway

    SPILLWAY PARTS ITEM DESCRIPTION PART NUMBER Gasket, Spillway 05700-111-34-52 Spillway 05700-003-52-13 Lock Nut, 1/4-20 Hex with Nylon Insert 05310-374-01-00 Drain Link 05700-003-78-49 Connector, Drain Link 05700-002-38-10 Drain Seat 05700-004-37-18 07610-004-25-06-R...

  • Page 58: Pump & Motor

    PUMP & MOTOR PARTS Complete Assembly Complete Pump & LTH 3-Phase Only Motor Assembly See Motor Rotation section. 06105-004-24-80 Motor Only 06105-004-32-04 Parts Pump Dishcharge Hose (not shown) 05700-003-78-50 Hose Clamp, 1 5/16" to 2 1/4" S/S (not shown) 04730-719-18-00 (2 required) ITEM DESCRIPTION PART NUMBER...

  • Page 59: I-E-Lth Booster Tank

    I-E-LTH BOOSTER TANK PARTS Complete Booster Tank Assembly 05700-004-52-09 07610-004-25-06-R...
  • Page 60 I-E-LTH BOOSTER TANK PARTS ITEM DESCRIPTION PART NUMBER Booster Tank 05700-004-52-23 Plate, Booster Tank Base 05700-004-48-90 Bracket, Booster Mount 05700-004-48-83 Bracket, Booster Tank 05700-004-52-08 Plumbing, Booster Inlet/Outlet 05700-004-52-28 Hose, Blue 3/4" x 45" 05700-004-52-27 Hose, Red 3/4" x 49" 05700-004-52-26...

  • Page 61: Frame

    FRAME PARTS XL-E-FL has flanged feet in the rear. See next page. ITEM DESCRIPTION PART NUMBER Splash Shield 05700-004-01-54 Strainer 05700-004-09-08 Strainer Stop 05700-004-18-33 Accumulator 05700-004-08-39 05340-108-01-03 Screw, 1/4-20 x 1 1/2" 05305-274-23-00 Locknut, 1/4-20 (not shown) 05310-374-01-00 Bolt, 1/4-20 x 3/8" 05305-274-20-00 05310-374-02-00 07610-004-25-06-R...

  • Page 62: Miscellaneous Parts

    MISCELLANEOUS PARTS PARTS Parts not shown to scale in relation to each other. Drain Stopper Assembly, I-E/I-E-LTH 05700-003-78-51 Bulk Head Fitting Drain Stopper Assembly, I-HH 04730-011-45-21 05700-004-27-31 Blue Chemical Tubing (120") 05700-011-37-17 Red Chemical Tubing (120") 05700-011-37-15 White Chemical Tubing (120")

  • Page 63: Schematics

    I-E/I-HH 115 V, 60 HZ, 1-PHASE SCHEMATICS NOBLE I-E/I-HH 07610-004-25-06-R...

  • Page 64: I-E/I-Hh 230 V, 60 Hz, 1-Phase

    I-E/I-HH 208/230 V, 60 HZ, 1-PHASE SCHEMATICS NOBLE I-E/I-HH 07610-004-25-06-R...

  • Page 65: I-E-Lth 208/230 V, 60 Hz, 1/3 Phase

    I-E-LTH 208/230 V, 60 HZ, 1/3 PHASE SCHEMATICS NOBLE I-E-LTH 07610-004-25-06-R...

  • Page 66: I-E-Fl 115 V, 60 Hz, 1-Phase

    I-E-FL 115 V, 60 HZ, 1-PHASE SCHEMATICS NOBLE I-E-FL 07610-004-25-06-R...
  • Page 68 NOBLE DOOR-TYPE DISHMACHINES Noble Warewashing • Lancaster, Pennsylvania www.nobleproducts.biz For Service Call 1-888-800-5672 Noble I-E Series/I HH Manual • 07610-004-25-06-R...

This manual is also suitable for:

I-e-flI-e-lthI hh

Table of Contents