Related Manuals for Smarteh Longo LPC-2.DX1
Summary of Contents for Smarteh Longo LPC-2.DX1
- Page 1 USER MANUAL Longo programmable controller LPC-2.DX1 Relay module Version 2 SMARTEH d.o.o. / Poljubinj 114 / 5220 Tolmin / Slovenia / Tel.: +386(0)5 388 44 00 / e-mail: info@smarteh.si / www.smarteh.si...
- Page 2 Longo programmable controller LPC-2.DX1 Written by SMARTEH d.o.o. Copyright © 2024, SMARTEH d.o.o. User Manual Document Version: 2 May, 2024...
- Page 3 24 months is valid from the date of sale to the end buyer, but not more than 36 months after delivery from Smarteh. In case of claims within warranty time, which are based on material malfunctions the producer offers free replacement. The method of return of malfunctioned module, together with description, can be arranged with our authorized representative.
-
Page 4: Table Of Contents
Longo programmable controller LPC-2.DX1 Longo programmable controller LPC-2.DX1 1 ABBREVIATIONS................1 2 DESCRIPTION...................2 3 FEATURES..................3 4 OPERATION..................4 4.1 SmartehIDE Parameters...............5 5 INSTALLATION..................6 5.1 Connection scheme..............6 5.2 Mounting instructions..............8 6 TECHNICAL SPECIFICATIONS..............10 7 MODULE LABELING................11 8 CHANGES ..................12 9 NOTES..................13... -
Page 5: Abbreviations
Longo programmable controller LPC-2.DX1 1 ABBREVIATIONS Direct Current Alternating Current Receive Transmit UART Universal Asynchronous Receiver-Transmitter Normally Open Programmable Logic Controller... -
Page 6: Description
Longo programmable controller LPC-2.DX1 2 DESCRIPTION LPC-2.DX1 is a relay output module with inrush current protection and galvanic isolated output. It can be used in a wide range of operation. It is suitable to be used with inductive or capacitive loads (e.g. -
Page 7: Features
Longo programmable controller LPC-2.DX1 3 FEATURES Figure 1: LPC-2.DX1 module Table 1: Technical data Relay digital output with make contacts (NO), inrush current limited, galvanic isolated Signal LED Blown fuse detection Supplied from main module Small dimensions and standard DIN EN50022-35 rail mounting... -
Page 8: Operation
4 OPERATION LPC-2.DX1 module can be controlled from main PLC module (e.g. LPC-2.MC9, LPC-2.MM1). Module parameters can be read or written via Smarteh IDE software. LPC-2.DX1 module can also be controlled by the remote input output main module (e.g. LPC-2.MU1). -
Page 9: Smartehide Parameters
Longo programmable controller LPC-2.DX1 4.1 SmartehIDE Parameters Input Internal temperature [DX1_x_ai_internal_temp]: Internal temperature measurement on the PCB. Type: UINT 0 .. 65535 → 0 .. 655.35 °C Raw to engineering data: Fuse status [DX1_x di_fuse_status]: Fuse digital input status. Type: BOOL →... -
Page 10: Installation
Longo programmable controller LPC-2.DX1 5 INSTALLATION 5.1 Connection scheme Figure 3: Connection scheme Table 2: IN IN.3 Power supply input – line, 100 .. 240 V AC, 50/60 Hz IN.4 Power supply input – neutral, 100 .. 240 V AC, 50/60 Hz Table 3: OUT OUT.1 Power supply output –... - Page 11 Longo programmable controller LPC-2.DX1 Table 6: K1 Internal BUS Data & DC power supply Connection to I/O module Table 7: K2 Internal BUS Data & DC power supply Connection to I/O module...
-
Page 12: Mounting Instructions
Longo programmable controller LPC-2.DX1 5.2 Mounting instructions Figure 4: Housing dimensions Dimensions in millimeters. • All connections, module attachments and assembling must be done while module is not connected to the main power supply. Mounting instructions: 1. Switch OFF main power supply. 2. - Page 13 Longo programmable controller LPC-2.DX1 Figure 5: Minimum clearances The clearances above must be considered before module mounting. Figure 6: Fuse replacement...
-
Page 14: Technical Specifications
Longo programmable controller LPC-2.DX1 6 TECHNICAL SPECIFICATIONS Table 8: Technical specifications Power supply From the main module via internal bus Max. power consumption 0.5 W Rated input voltage 100 .. 240 V AC, 50/60 Hz Maximum operating current SW-defined minimum OFF time 20 s Fuse 4 A (T-slow), 250 V, Cartridge fuse 5x20 mm... -
Page 15: Module Labeling
EEE – version code (reserved for future HW and/or SW firmware upgrades). ▪ 3. S/N: SSS-RR-YYXXXXXXXXX - serial number. SSS – short product name, ◦ RR – user code (test procedure, e.g. Smarteh person xxx), ◦ YY – year, ◦ XXXXXXXXX – current stack number. -
Page 16: Changes
Longo programmable controller LPC-2.DX1 8 CHANGES The following table describes all the changes to the document. Date Description 10.05.24 The initial version, issued as LPC-2.DX1 module UserManual. -
Page 17: Notes
Longo programmable controller LPC-2.DX1 9 NOTES...
Need help?
Do you have a question about the Longo LPC-2.DX1 and is the answer not in the manual?
Questions and answers