Related Manuals for Nice BiDi-Awning
Summary of Contents for Nice BiDi-Awning
- Page 1 BiDi-Awning Exterior bidirectional interface for tubular motor EN - Instructions and warnings for installation and use v1.5...
-
Page 2: Warnings And General Precautions
The BiDi-Awning control unit enables the control of a mains-powered, single-phase asynchronous motor with connection types: Down, Com- mon, Up, used for the automation of awnings, rolling shutters and similar. The BiDi-Awning control unit incorporates a radio transceiver operating at the frequency of 433.92 MHz with the rolling code technology to guarantee optimal safety levels. -
Page 3: Technical Specifications
Warning All technical specifications stated in this section refer to an ambient temperature of 20 °C (± 5 °C). Nice S.p.A. reserves the right to modify the product at any time when necessary, while maintaining the same functionalities and intended use. - Page 4 • The BiDi-Awning control unit was designed for insertion in a junction box or wall box; its housing doesn't have any protection against water and has only basic protection against contact with solid parts. Never place BiDi-Awning in inadequately protected environments.
- Page 5 4.4 - Power supply The electric power supply of the control unit must be connected using terminals L-N-PE (Line, Neutral, Grounding). The BiDi-Awning control unit can operate with supply voltage of 100 to 240 Volts and frequency of 50 or 60 Hz.
- Page 6 5.2 - Memorising transmitters in Mode I When there is no transmitter memorised, the first one can be memorised during a startup phase according to the following procedure. Table A4 - BiDi-Awning - Memorising first transmitter during startup in Mode I Nº...
- Page 7 The transmitters can be memorised with the programming pushbutton according to the following procedure. Table A5 - BiDi-Awning - Memorising other transmitters in Mode I Nº Description Example Press the programming key of the already memorised transmitter. Wait until you hear 2 beeps.
- Page 8 5.4 - Memorising transmitters in Mode II Table A7 - BiDi-Awning - Memorising first and other transmitters in Mode II Nº Description Example Press the programming key of the already memorised transmitter. Wait until you hear 2 beeps. Press the programming key the number of times required for a particulr command...
- Page 9 CAUTION! – If the automatic calibration diddn't recognize properly the limit positions, perform the manual calibration instead. CAUTION! – There is a fixed operation time of 240 s when module isn't calibrated. To perform automatic calibration, follow the steps from the table below: Table A9 - BiDi-Awning - Automatic calibration Nº Description Example The programming procedure ends automatically when you hear one long beep.
- Page 10 6.2 - Partial positions The BiDi-Awning control unit enables setting quickly accessible partial positions. Partial positions work only with transmitters memorized in Mode I. Table A11 - BiDi-Awning - Available partial positions Nº Press at the same time to activate...
- Page 11 The motor makes a move between the virtual and mechanical limit switch. The programming procedure ends automatically. 6.4 - Venetian blinds The BiDi-Awning control unit enables controlling slats for Venetian blinds. When the Venetian blinds control is enabled, pressing the key/ the 1st channel or the key / the 3rd channel moves the slats by 20%.
- Page 12 6.5 - Climatic sensors The control unit supports Nice radio mono and bidirectional climatic sensors. Memorisation of a climatic sensor needs to be carried out like that of a normal transmitter (follow the procedure in Table A5). Thresholds for commands needs to be programmed on the climatic sensor.
- Page 13 6.7 - Factory reset If the control unit needs to be reset to the factory settings (all transmitters and setting are deleted), follow the steps from the table below: Table A20 - BiDi-Awning - Restoring to factory defaults with already memorised transmitter Nº...
- Page 14 If the first memorized transmitter is inoperable, lost or isn't equipped with the programming PRG button, you can reset the control unit to the factory settings with not memorized transmitter. Follow the steps from the table below: Table A21 - BiDi-Awning - Restoring to factory defaults with not memorised transmitter Nº...
-
Page 15: Declaration Of Conformity
CAUTION! – local legislation may envisage serious fines in the event of abusive disposal of this product. DECLARATION OF CONFORMITY Nice S.p.A. declares that the radio equipment type BiDi-Awning complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at: http://www.niceforyou.com/en/support... - Page 16 Nice S.p.A Oderzo TV Italia www.niceforyou.com info@niceforyou.com...
Need help?
Do you have a question about the BiDi-Awning and is the answer not in the manual?
Questions and answers