CONTENTS 1. Safety Instructions 2. What’s in the Box 3. Using Your T8 Important Tips before Use Preparation LED Indication Charging Modes Switching Modes Cleaning Modes Set Time and Scheduled Cleaning 4.Cleaning and Maintenance T8 Anatomy Clean the Rolling Brush...
Page 3
To reduce the risk of injury or damage, read these safety instructions carefully and keep them at hand when setting up, using, and maintaining this device. Safety Instructions for T8 and Accessories Warning 1. Do not disassemble, repair or refit the product without authorization;...
Page 4
Please recycle the battery safely for environmental protection. Safety Instructions for T8 and Accessories 1. Always use a dedicated battery adapter to avoid leakage, heating or rupture.
Page 5
11. The power supply must be removed from the socket-outlet before cleaning or maintaining the device. 12. The battery must be removed from the device before it is scrapped. 13. The device must be disconnected from the mains supply when removing the battery.
2. What’s in the Box Main Body Remote Control Charging Base Power Adapter (2 * AAA Batteries required but NOT included) High-effective Cleaning Tool Side Brushes(4) Filter/Sponge While the accessories provided for some models are slightly different, they are subject to the actual product.
Remove power cords and small objects from the floor that may become entangled with the T8. The T8 may climb on top of objects less than 0.63 in/16 mm in height. Remove these objects if possible. Do NOT stand around narrow places, such as thresholds and aisles, to reduce the uncovered rate.
Preparation Install the side brushes before use. Please note L and R should correspond to each other when installing the side brushes. Turn on the main power switch on the side of T8. Remove before use Remove the protective film before use.
Page 9
Install 2 AAA batteries (Not included in the package) into the remote control. Power On/Off Display Screen Return for Auto Plan Cleaning Charging Confirm Direction Clock Settings Suction Settings Edge Cleaning Schedule Note: For App users, please refer to our User Guide for App&Alexa. When the device is in the vicinity of the charging base and the virtual protection wall, it may not be able to receive the instructions issued by the remote control.
Method 1: Press on the remote control to return the T8 to the Charging Base. Method 2: When cleaning is completed, or the battery is too low, the T8 will automatically start finding the charging base to charge itself. Please keep the...
Spot Cleaning mode. 3. Edge Cleaning The Tesvor T8 reduces its speed when it detects a wall and then follows the wall to ensure the edge is cleaned thoroughly. Click the Edge Cleaning icon...
Page 13
Auto-charge and Resume original The robot will automatically dock the charging base to coordinates charge itself once the battery is too low.Navigation with Visual Localization helps the robot remember its location and the planned route after full charging. It resumes Resume cleaning with the original coordinates generated by the Auto-charge...
Set Time and Scheduled Cleaning Set Time Note: 1. Make sure the main power switch on the bottom of the T8 is turned on. 2. Press on the remote control. The time will blink on the display. 3. Press to set the “hour” and “minute”.
4.Cleaning and Maintenance T8 Anatomy Top & Side Bumper Wi-Fi Indicator Control button Camera DC power jack Power switch Dust box release button Swivel Wheel Charging shrapnel Side brushes Battery Compartment Wheels Rolling brush Dust box...
Charging Base Charging indicator light DC power jack Charging terminal Dust box Pre-filter High-performance filter Filter sponge Dust box Dust box cover Clean the Rolling Brush 1.Open the rolling brush components. 2.Remove the rolling brush shaft and clean off any debris and hair. Clean the Side Brushes Foreign substances, such as hair, can easily get tangled in the side brushes, and dirt may adhere to them.
2) Carefully unwind and pull off any hair or string that is wrapped between the main unit and the side brushes. 3) Use a cloth dampened with warm water to remove dust from the brushes or to gently reshape them. Note Only use the side brushes when they are completely dry.
Replace the Side Brushes The side brushes may become bent or damaged after being used for a period of time. Follow the instructions below to replace them. Pull off the old side brushes and snap the new ones into place. Clean the Sensors and Charging Terminals To maintain the best performance, clean the drop sensors and charging terminal regularly.
The bot might deviate the route when running on carpets, which takes longer to adjust to the right turning angle. If your issues can not be fixed, please send emails to service@tesvor.com. We provide warranty for all quality related issues.
Page 20
240 - 360 mins 330mm Diameter of main unit 81mm Thickness of main unit Net weight of main unit 3.0kg 7. Customer Service If you have any issues, please contact us by Online Service on the app or send email to service@tesvor.com.
Need help?
Do you have a question about the T8 and is the answer not in the manual?
Questions and answers