Lantronix xDirect-IAP Quick Start Manual

xDirect
WHAT'S IN THE BOX
xDirect -IAP Quick Start Guide
™
WHAT'S In THE BOX
xDirect ™ -IAP Quick Start Guide
WHAT'S In THE BOX
Power / Status WHAT'S In THE BOX Quick Start Guide xDirect Device Server LED 1 HARDWARE REvIEW Depending on the xDirect™ model, the following pinouts apply Quick Start Guide ™ xDirect LED Serial RX xDIRECT PINOUTS LED on bottom Serial TX Reset Switch - Activity LED Link LED RJ45 Serial Port DB9 Power Supply* 3.5" (88.9 mm) (mini USB connector) * not included with xDirectPoE version 5vDC with International adapters Power Port Female (DCE)
9 (out) (out) (in) (out) (in) (out) (in) 6 VDC 9 TX+ RX- 3. For standard xDirect units, supply power to your unit using the power 2. Connect an Ethernet cable to the RJ45 port. 1. Connect a serial device to the xDirect. 2 HARDWARE InSTALLATIOn Contact 1 CTS DB9F in RS232 Mode RTS (All models) DSR DB9F in RS422/485 (4-Wire) Mode TX (xDirect485 & PoE Models) RX GND DTR (in) 5 5-15 1 VDC GND Quick Start Guide 5 RJ45 ETHERNET 5-15 Link LED (in) Activity LED supply that was included in the packaging. Contact 8 DCD 1 THIS COMPLETES THE HARDWARE INSTALLATION. RX+ TX- 4. For the xDirectPoE version, power is supplied to your unit over an 5-15 9 DB9F in RS485 (2-Wire) Mode 1 Ethernet interface using an 802.3af PoE compliant power source such (in) TX/ RX+ TX/RX- 5 GND (xDirect485 & PoE Models) 6 VDC as a PoE mid-span or PoE Ethernet switch. 6 xDirect Device Server * not included with xDirect-IAP PoE version 5vDC with International adapters Power Supply*
1 HARDWARE REvIEW
Power / Status LED LED Serial RX Female (DCE) Serial Port DB9 Power Port (mini USB connector)
Link LED RJ45 Reset Switch - LED Serial TX
xDIRECT-IAP PINOUTS Activity LED on bottom 3.5" (88.9 mm)
9 5 (out) RX (in) TX (in) DTR GND (out) 6 1 DCD 5 9 GND RX+ TX- 1 6 5 9 GND TX/RX- 6 1
DB9F in RS232 Mode 5-15 VDC (in) DSR (out) CTS (out) RTS (in) DB9F in RS422/485 (4-Wire) Mode (in) VDC 5-15 TX+ RX- (in) VDC DB9F in RS485 (2-Wire) Mode 5-15 RX+ TX/
RJ45 ETHERNET Power Supply*
Contact 8 Link LED Activity LED Contact 1
1. Connect a serial device to the xDirect. 2 HARDWARE InSTALLATIOn 4. For the xDirect-IAP PoE version, power is supplied to your unit over
2. Connect an Ethernet cable to the RJ45 port. unit using the power supply that was included in the packaging. 3. For the standard xDirect-IAP (non-PoE) version, supply power to your THIS COMPLETES THE HARDWARE INSTALLATION. such as a PoE mid-span or PoE Ethernet switch. an Ethernet interface using an 802.3af PoE compliant power source 5vDC with International adapters
Quick Start Guide xDirect Device Server
* not included with xDirect-IAP PoE version
1 HARDWARE REvIEW
Serial Port DB9
Female (DCE)
Serial RX
Power / Status LED
LED Power Port
(mini USB connector)
Serial TX
Link LED LED
RJ45
Reset Switch -
on bottom
Activity LED
3.5" (88.9 mm)
xDIRECT-IAP PINOUTS
DTR TX RX DCD
GND (in) (in) (out) (out) GND RX+ TX- GND TX/RX-
5 1 5 1 5 1
9 6 9 6 9 6
5-15 CTS RTS DSR 5-15 TX+ RX- 5-15 TX/
VDC (out) (in) (out) VDC VDC RX+
(in) (in) (in)
DB9F in RS232 Mode DB9F in RS422/485 (4-Wire) Mode DB9F in RS485 (2-Wire) Mode
RJ45 ETHERNET
Link LED Activity LED
Contact 8 Contact 1
2 HARDWARE InSTALLATIOn
1. Connect a serial device to the xDirect. 4. For the xDirect-IAP PoE version, power is supplied to your unit over
an Ethernet interface using an 802.3af PoE compliant power source
2. Connect an Ethernet cable to the RJ45 port.
such as a PoE mid-span or PoE Ethernet switch.
3. For the standard xDirect-IAP (non-PoE) version, supply power to your
THIS COMPLETES THE HARDWARE INSTALLATION.
unit using the power supply that was included in the packaging.
Quick Start Guide
1 HARDWARE REVIEW
Power / Status
LED
Link LED
RJ45
Reset Switch
- on bottom
Activity LED
xDIRECT-IAP PINOUTS
DTR TX RX DCD
GND (in) (in) (out) (out)
5
9
5-15 CTS RTS DSR
(out) (in) (out)
VDC
(in)
DB9F in RS232 Mode
RJ45 ETHERNET
Link LED
Contact 8
2 HARDWARE INSTALLATION
1. Connect a serial device to the xDirect-IAP device server.
2. Connect an Ethernet cable to the RJ45 port.
3. For the standard xDirect-IAP (non-PoE) version, supply power
to your unit using the power supply that was included in the
packaging.
-IAP Quick Start Guide
™
xDirect-IAP Device Server
Serial RX
LED
Serial TX
LED
1 5
6 9
DB9F in RS422/485 (4-Wire) Mode
Activity LED
Contact 1
Serial Port DB9
Female (DCE)
GND RX+ TX-
1
6
5-15 TX+ RX-
VDC
(in)
4. For the xDirect-IAP PoE version, power is supplied to your unit
over an Ethernet interface using an 802.3af PoE compliant
power source such as a PoE mid-span or PoE Ethernet switch.
THIS COMPLETES THE HARDWARE INSTALLATION.
Power Supply*
5VDC with International adapters
* Not included with xDirect-IAP PoE version
Power Port
(mini USB connector)
3.5" (88.9 mm)
GND TX/RX-
5
9
5-15 TX/
RX+
VDC
(in)
DB9F in RS485 (2-Wire) Mode
1
6