Lantronix xDirect Quick Start Manual

xDirect
WHAT'S In THE BOX
xDirect Quick Start Guide
™
WHAT'S In THE BOX
xDirect ™ Quick Start Guide
WHAT'S In THE BOX
Quick Start Guide xDirect Device Server 5vDC with International adapters Power Supply* * not included with xDirectPoE version
1 HARDWARE REvIEW
Power / Status LED LED Serial RX Serial Port DB9 Female (DCE) Power Port
Link LED RJ45 Reset Switch - LED Serial TX (mini USB connector)
Depending on the xDirect™ model, the following pinouts apply xDIRECT PINOUTS Activity LED on bottom 3.5" (88.9 mm)
5 9 RX (out) (in) TX (in) DTR GND (out) 1 6 DCD 5 9 GND RX+ TX- 6 1 9 5 GND TX/RX- 6 1
DB9F in RS232 Mode RTS VDC 5-15 CTS (in) (out) (in) DSR (out) DB9F in RS422/485 (4-Wire) Mode (in) VDC 5-15 TX+ RX- DB9F in RS485 (2-Wire) Mode VDC (in) 5-15 RX+ TX/
RJ45 ETHERNET (All models) (xDirect485 & PoE Models) (xDirect485 & PoE Models) Power Supply*
Link LED Contact 8 Activity LED Contact 1
2 HARDWARE InSTALLATIOn
2. Connect an Ethernet cable to the RJ45 port. 1. Connect a serial device to the xDirect. 3. For standard xDirect units, supply power to your unit using the power as a PoE mid-span or PoE Ethernet switch. Ethernet interface using an 802.3af PoE compliant power source such 4. For the xDirectPoE version, power is supplied to your unit over an 5vDC with International adapters
supply that was included in the packaging. THIS COMPLETES THE HARDWARE INSTALLATION.
Quick Start Guide xDirect Device Server
* not included with xDirectPoE version
1 HARDWARE REvIEW
Serial Port DB9
Female (DCE)
Serial RX
Power / Status LED
LED
Power Port
(mini USB connector)
Serial TX
Link LED LED
RJ45
Reset Switch -
on bottom
Activity LED
3.5" (88.9 mm)
xDIRECT PINOUTS
Depending on the xDirect™ model, the following pinouts apply
DTR TX RX DCD
GND (in) (in) (out) (out) GND RX+ TX- GND TX/RX-
5 1 5 1 5 1
9 6 9 6 9 6
5-15 CTS RTS DSR 5-15 TX+ RX- 5-15 TX/
VDC (out) (in) (out) VDC VDC RX+
(in) (in) (in)
DB9F in RS232 Mode DB9F in RS422/485 (4-Wire) Mode DB9F in RS485 (2-Wire) Mode
(All models) (xDirect485 & PoE Models) (xDirect485 & PoE Models)
RJ45 ETHERNET
Link LED Activity LED
Contact 8 Contact 1
2 HARDWARE InSTALLATIOn
1. Connect a serial device to the xDirect. 4. For the xDirectPoE version, power is supplied to your unit over an
Ethernet interface using an 802.3af PoE compliant power source such
2. Connect an Ethernet cable to the RJ45 port.
as a PoE mid-span or PoE Ethernet switch.
3. For standard xDirect units, supply power to your unit using the power
THIS COMPLETES THE HARDWARE INSTALLATION.
supply that was included in the packaging.
Quick Start Guide
1 HARDWARE REvIEW
Power / Status
LED
Link LED
RJ45
Reset Switch -
on bottom
Activity LED
xDIRECT PINOUTS
Depending on the xDirect™ model, the following pinouts apply
DTR TX RX DCD
GND (in) (in) (out) (out)
5
9
5-15 CTS RTS DSR
(out) (in) (out)
VDC
(in)
DB9F in RS232 Mode
(All models)
RJ45 ETHERNET
Link LED
Contact 8
2 HARDWARE InSTALLATIOn
1. Connect a serial device to the xDirect.
2. Connect an Ethernet cable to the RJ45 port.
3. For standard xDirect units, supply power to your unit using the power
supply that was included in the packaging.
Quick Start Guide
™
xDirect Device Server
Serial RX
LED
Serial TX
LED
1 5
6 9
DB9F in RS422/485 (4-Wire) Mode
(xDirect485 & PoE Models)
Activity LED
Contact 1
Serial Port DB9
Female (DCE)
GND RX+ TX-
1
6
5-15 TX+ RX-
VDC
(in)
4. For the xDirect PoE version, power is supplied to your unit over an
Ethernet interface using an 802.3af PoE compliant power source such
as a PoE mid-span or PoE Ethernet switch.
THIS COMPLETES THE HARDWARE INSTALLATION.
Power Supply*
5vDC with International adapters
* not included with xDirectPoE version
Power Port
(mini USB connector)
3.5" (88.9 mm)
GND TX/RX-
5
9
5-15 TX/
RX+
VDC
(in)
DB9F in RS485 (2-Wire) Mode
(xDirect485 & PoE Models)
1
6