Lantronix XPort Pro Integration Manual
  1. Manuals
  2. Brands
  3. Lantronix Manuals
  4. Server
  5. xport pro
  6. Integration manual
Lantronix XPort Pro Integration Manual

Lantronix XPort Pro Integration Manual

Embedded device server
Hide thumbs Also See for XPort Pro:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
Integration Guide
Part Number 900-557
Revision E September 2011

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the XPort Pro and is the answer not in the manual?

Questions and answers

Related Manuals for Lantronix XPort Pro

Summary of Contents for Lantronix XPort Pro

  • Page 1 Integration Guide Part Number 900-557 Revision E September 2011...

  • Page 2: Copyright And Trademark

    Copyright and Trademark © 2011 Lantronix. All rights reserved. No part of the contents of this book may be transmitted or reproduced in any form or by any means without the written permission of Lantronix. Printed in the United States of America.

  • Page 3: Table Of Contents

    List of Tables ........................ 4 1. Introduction About the Integration Guide..................5 Additional Documentation..................... 5 2. Description and Specifications The XPort Pro Features ....................6 XPort Pro Block Diagram ....................7 PCB Interface ....................... 7 Ethernet Interface ......................9 LEDs ..........................9 Dimensions .........................

  • Page 4: List Of Figures

    List of Figures Figure 2-1. Side View of the XPort Pro ....................7 Figure 2-2. XPort Pro Block Diagram ..................... 7 Figure 2-3. XPort Pro LEDs ........................9 Figure 2-4. Front View .......................... 10 Figure 2-5. Bottom View ........................10 Figure 2-6.

  • Page 5: Introduction About The Integration Guide

    About the Integration Guide This guide provides the information needed to integrate the XPort Pro™ device server into a customer printed circuit board. This manual is intended for engineers responsible for integrating the XPort Pro into their product. Note: This document covers XPort Pro™ Device Server versions XPP1002000-01R, XPP100200S-01R, XPP1003000-01R, XPP100300S-01R, XPP1003000-02R and XPP100300S-02R.

  • Page 6: Description And Specifications

    Ethernet magnetics  Power supply filters  Reset circuit  +1.5V regulator  Crystals and Ethernet LEDs The XPort Pro requires +3.3-volt power and is designed to operate in an extended temperature range (see technical data). XPort Pro Integration Guide...

  • Page 7: Xport Pro Block Diagram

    Figure 2-2. XPort Pro Block Diagram PCB Interface The XPort Pro has a serial port compatible with data rates up to 921600 bps. The serial signals (pins 4–8) are 3.3V CMOS logic level. The serial interface pins include +3.3V, ground, and reset. The serial signals connect to an internal UART driven at 3.3V.

  • Page 8: Table 2-1. Pcb Interface Signals

    Modem control: DCD (Data Carrier Detect) input read by the built-in UART for connection to DTR of attached device. • Programmable input/output: CP3 can be driven or read through software control, independent of serial port activity. XPort Pro Integration Guide...

  • Page 9: Ethernet Interface

    Ethernet Interface The Ethernet interface magnetics, RJ45 connector, and Ethernet status LEDs are all in the device server shell. The XPort Pro PHY is Auto MDIX capable allowing connection to either straight through or cross over Ethernet cables. Table 2-2 Ethernet Interface Signals (Industry Standards)

  • Page 10: Dimensions

    2: Description and Specifications Dimensions The XPort Pro dimensions are shown in the following drawings. Figure 2-4. Front View 18.25 [0.719] FRONT VIEW 16.25 [0.640] DIMS = mm (in) 11.55 [0.455] 7.15 [0.281] LEFT RIGHT CONTACT 8 CONTACT 1 14.50 [0.571] 4.03 [0.158]...

  • Page 11: Recommended Pcb Layout

    Adding 1 inch square inch of copper flood on the PCB is adequate to allow the XPort Pro to work up to +85°C. If the application does not expect to see temperatures up to +85°C the heat sink may be smaller than 1 square inch.

  • Page 12: Product Information Label

    Electrical Specifications Caution: Stressing the device above the rating listed in this table may cause permanent damage to the XPort Pro. Exposure to Absolute Maximum Rating conditions for extended periods may affect the XPort Pro’s reliability. Table 2-3. Absolute Maximum Ratings...

  • Page 13: Functional Specifications

    EN61000-4-3 (3 V/m (Unmodulated R.M.S.), 80 MHz - 1 GHz, 80% AM (1 kHz))  EN61000-4-4 (Ethernet Port: ±0.5 kV (Peak), 5 kHz)  EN61000-4-6 (Signal Port(s):3 V (Unmodulated R.M.S), 0.15 MHz - 80 MHz, 80% AM (1 kHz)  EN61000-4-8 (50 Hz, 1.0 A/m (R.M.S.)) XPort Pro Integration Guide...

  • Page 14: A: Xport Pro 485 Connection Diagram

    The following example illustrates a connection between the XPort Pro and an external transceiver IC: XPort Pro Integration Guide...

  • Page 15: B: Compliance Information

    (According to ISO/IEC Guide 22 and EN 45014) Manufacturer’s Name & Address: Lantronix 167 Technology Drive, Irvine, CA 92618 USA Declares that the following product: Product Name Model: XPort Pro Embedded Device Server Conforms to the following standards or other normative documents: Electromagnetic Emissions/Immunity: ...
  • Page 16 B: Compliance Information RoHS Notice All Lantronix products in the following families are China RoHS-compliant and free of the following hazardous substances and elements: • • • Lead (Pb) Mercury (Hg) Polybrominated biphenyls (PBB) • • • Cadmium (Cd) Hexavalent Chromium (Cr (VI)) Polybrominated diphenyl ethers (PBDE) •...

  • Page 17: C: Warranty

    For details on the Lantronix warranty replacement policy, go to our web site at www.lantronix.com/support/warranty. XPort Pro Integration Guide...

Table of Contents