Subscribe to Our Youtube Channel
Related Manuals for Hilti WSC 7.25
Summary of Contents for Hilti WSC 7.25
- Page 1 WSC 7.25 Operating instructions Printed: 07.07.2013 | Doc-Nr: PUB / 5144811 / 000 / 00...
- Page 2 "± +± +“ +≠ "≠ "“ +Ç Printed: 07.07.2013 | Doc-Nr: PUB / 5144811 / 000 / 00...
- Page 3 5/ 6 0-45° (50) Printed: 07.07.2013 | Doc-Nr: PUB / 5144811 / 000 / 00...
- Page 4 1400/3000 mm WGS 1400-2 60° 45° 30° 22.5° 0° 22.5°30° 45° Printed: 07.07.2013 | Doc-Nr: PUB / 5144811 / 000 / 00...
-
Page 5: Table Of Contents
In these operating instructions, the designation “the the first time. power tool” always refers to the WSC 7.25 circular saw. Always keep these operating instructions to- Components, operating controls and indicators 1 gether with the power tool. -
Page 6: Description
(HSS steel) is not permissible. Sawing metals is not permissible. Do not use the power tool to cut tree branches or logs. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. - Page 7 Operating instructions Hexagon socket wrench Parallel guide (rip fence) Hilti cardboard box or toolbox 2.7 Using extension cords Use only extension cords of a type approved for the application and with conductors of adequate cross section. The power tool may otherwise lose performance and the extension cord may overheat. Check the extension cord for damage at regular intervals.
-
Page 8: Accessories
Noise and vibration information for the WSC 7.25 (measured in accordance with EN 60745-2-5): Typical A-weighted sound power level 105 dB (A) Typical A-weighted emission sound pressure level. -
Page 9: Safety Instructions
Triaxial vibration values (vibration vector sum) Sawing in wood, a 2.5 m/s² Uncertainty (K) 1.5 m/s² Other information about the power tool Protection class Protection class II (double insulated), see rating plate 5 Safety instructions 5.1 General Power Tool Safety Warnings 5.1.3 Personal safety a) Stay alert, watch what you are doing and use WARNING... - Page 10 d) Store idle power tools out of the reach of chil- 5.3 Further safety instructions for all saws dren and do not allow persons unfamiliar with the Kickback causes and related warnings power tool or these instructions to operate the kickback is a sudden reaction to a pinched, bound or power tool.
- Page 11 For all other of the type recommended by Hilti for wood dust sawing, the lower guard should operate automatic- and/or mineral dust together with this tool. Ensure ally.
-
Page 12: Operation
tion, protective gloves and breathing protection while 5.5.5 Personal protective equipment the tool is in use. 5.5.6 Protective devices Do not switch the power tool on if the saw blade, the blade guard, the pivoting guard or the riving knife are not fitted correctly. -
Page 13: Care And Maintenance
Slacken the clamping screw on the base plate. 6.3 Adjusting the cutting angle 5 Slide both arms of the parallel guide under the The power tool can be set to any angle between 0 and clamping screw. 45º for bevel cuts. Angles of up to 50° can be set after Set the desired cutting width. -
Page 14: Troubleshooting
Clean out the chip ejector channel. 9 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. -
Page 15: Manufacturer's Warranty - Tools
10 Manufacturer’s warranty - tools Hilti warrants that the tool supplied is free of defects in Additional claims are excluded, unless stringent na- material and workmanship. This warranty is valid so long tional rules prohibit such exclusion. In particular, Hilti... - Page 16 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 3361 | 0613 | 00-Pos. 9 | 1 Printed in Czech Republic © 2013 Right of technical and programme changes reserved S. E. & O 234459 / A2 Printed: 07.07.2013 | Doc-Nr: PUB / 5144811 / 000 / 00...
Need help?
Do you have a question about the WSC 7.25 and is the answer not in the manual?
Questions and answers