Page 2
HYUNDAI HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 The engine exhaust from this product contains chemicals known to cause cancer, birth defects or other reproductive harm. Licensed by Hyundai Corporation Holdings, Korea. HY0343 HY0344 HY0345 HY0346 HY0348 HY0379 HY0380_Manual_EN_2024-03-14...
Page 3
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 This product is supported by Midland Power. Contact us directly for assistance and warranty help. Do not return this product to store. You must register online for your warranty to be valid. It only takes a minute, do it now while you still have your purchase receipt.
Page 4
HYUNDAI Thanks for choosing Hyundai! You're excited to get started, we'll keep this brief. READ THIS ENTIRE GUIDE BEFORE USING THIS PRODUCT AND SAVE FOR LATER USE. This user guide contains important instructions including safety, setup, operation, and maintenance that must be followed.
TABLE OF CONTENTS 1. Safety 2. Learn About Your Lawn Mower 3. Getting Started 4. Pre-Operation Check 4.1 Check Oil Level 4.2 Check the Fuel Level 5. Starting the Engine 5.1 Manual Recoil Start 6. Stopping the engine 7. Using your lawn Mower 7.1.
HYUNDAI 1. SAFETY DANGER! Using an engine indoors can kill you in minutes. The engine exhaust from this product contains chemicals known to cause cancer, birth defects or other reproductive harm. 1.1 OPERATOR SAFETY WARNING! Always perform an oil, fuel and air filter check before starting the engine.
Page 7
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 Place the lawn mower at least 3 feet away from buildings or other equipment during operation. Run the lawn mower on a level surface. Tilting the lawn mower may result in fuel spills.
Page 8
HYUNDAI Stop the blade(s) if the lawn mower has to be tilted for transportation when crossing surfaces other than grass, and when transporting the lawn mower to and from the area to be mowed. NEVER operate the lawn mower with defective guards, or without safety devices, for example deflectors and/or grass catchers, in place.
Page 9
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 Allow the lawn mower to cool down before performing any maintenance. Always stop the lawn mower before removing the oil filler cap. To reduce the fire hazard, keep the engine, silencer, battery compartment and gasoline storage area free of grass, leaves, or excessive grease.
This section will show you how to identify key parts of your lawn mower. Going over HH0343/HY0379 the terminology below will make sure we’re on the same page. 2.1 COMPONENT IDENTIFICATION HY0343, HY0379 Handle Grip Power Lever Upper Handle Lower Handle...
Page 11
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 HY0344 HY0344 Handle Grip Power Lever Upper Handle Rear Discharge Cover Starter Handle Lower Handle Fuel Tank Cap Deck Spark Plug Cap Oil Dipstick Front Wheel Side Discharge Chute Cutting Height Adjusting Handle...
Page 12
HYUNDAI HY0345 HY0345 Handle Grip Power Lever Upper Handle Rear Discharge Cover Starter Handle Lower Handle Fuel Tank Cap Deck Spark Plug Cap Oil Dipstick Front Wheel Side Discharge Chute Cutting Height Adjusting Handle Grass Bag Side Discharge Rear Wheel...
Page 13
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 HY0346/HY0380 HY0346, HY0380 Handle Grip Power Lever Upper Handle Rear Discharge Cover Lower Handle Starter Handle Fuel Tank Cap Deck Spark Plug Cap Oil Dipstick Front Wheel Side Discharge Chute Self Propelled Drive Lever...
Page 14
HYUNDAI HY0348 HY0348 Handle Grip Power Lever Speed Selection Lever Cup Holder Upper Handle Rear Discharge Cover Lower Handle Starter Handle Fuel Tank Cap Deck Spark Plug Cap Oil Dipstick Front Wheel Side Discharge Chute Self Propelled Drive Lever Cutting Height...
Page 15
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 2.2 CONTROL FUNCTIONS Cutting Height Adjusting Handle Adjust to set the cutting height. The cutting height ranges from 25mm to 75mm. Power Lever Engage the power lever to recoil start and operate the lawn mower.
Cut the four corners of the carton from top to bottom instead of attempting to lift it out of the box. 3.1 ASSEMBLING THE HANDLE On each side of lower handle, insert the bolt and secure with saddle washer and handle knob. HY0343, HY0379 HY0344, HY0345, HY0346, HY0348, HY0380 HY0345, HY0346, HY0348, HY0380...
Page 17
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 For HY0343, HY0344 and HY0379, on each side of the upper handle, insert the bolt and secure with saddle washer and handle knob. For HY0345, HY0344, HY0345, HY0346, HY0346, HY0348 and HY0380, insert the big lock knobs and secure with HY0348, HY0380 saddle washer and handle knob.
Page 18
HYUNDAI Ensure power lever cable is resting above lower and upper handles as pictured. HY0343, HY0344, HY0379 HY0346, HY0380...
Page 19
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 3.2 ASSEMBLING THE WHEELS (HY0343, HY0379 ONLY) NOTE HY0343, HY0379 Some models may come with spring washers for the wheels. If so, place washers on axles before assembling wheels. Slide larger wheels onto rear axles and secure with one nut each.
Page 20
HYUNDAI 3.3 ADJUSTING THE HANDLE Adjust Handle Height (HY0346, HY0348, HY0380 only) High Middle Turn the spring knob 90-degrees either direction to unlock. Choose a higher or lower bracket hole to set your handle height preference. Then turn the spring knob back 90-degrees until the silver bolt goes through that bracket hole.
Page 21
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 Move the upper handle to the desired height. Fix it to lower handle by using the hand knobs and the bolts on each side.
Page 22
HYUNDAI 3.4 ASSEMBLING THE RECOIL HANDLE LOOP (Optional) Fix the recoil handle connection cord with the recoil handle loop. Recoil Handle Loop Recoil Handle Recoil Handle Recoil Handle Loop...
Page 23
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 3.5 REMOVE OR KEEP THE MULCHING PLUG (HY0344, HY0345, HY0346, HY0348, HY0380 ONLY) Keep the plug installed for mulching, or remove when choosing to side or rear discharge. If removed the plug can be stored for later use.
Page 24
HYUNDAI 3.7 ASSEMBLING THE SIDE DISCHARGE CHUTE NOTE (HY0344, HY0345, HY0346, HY0348, HY0380 Only) Remove the grass Side Discharge bag and assemble the mulching plug before using the side discharge Cover Side Discharge function. Cover Lift the side discharge cover with one hand and hook in the side discharge chute with the other hand.
Page 25
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 3.8 ADD ENGINE OIL WARNING! Used motor oil can cause skin irritations if left in long-term contact with skin. Thoroughly wash off used oil as soon as possible with soap and water. Ensure the lawn mower is on a level surface.
Page 26
HYUNDAI NOTE Oil max. capacity: HY0343: 400 mL HY0344: 400 mL HY0345: 400 mL HY0346: 400 mL HY0348: 400 mL HY0379: 400 mL HY0380: 400 mL SAE10W-30 oil is recommended for general use.
Page 27
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 3.9 ADD FUEL WARNING! Gasoline is highly flammable and explosive under certain conditions. Refuel in a well-ventilated area with the engine stopped. DO NOT smoke or allow open flames or sparks in the area where the lawn mower is being refueled or where gasoline is stored.
Page 28
HYUNDAI Tighten the fuel cap securely. NOTE Only use unleaded gasoline (Pump Octane 87 or higher). NEVER use stale or contaminated gasoline, or an oil/gasoline mixture. Avoid getting dirt or water into the fuel tank. DO NOT use a mixture of gasoline containing methanol. This will cause serious damage to the engine.
Page 29
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 3.10 SETTING THE CUTTING HEIGHT WARNING! Adjust the cutting height only when the engine is switched off. Pull the adjusting handle out. Cutting Height Adjusting Handle Cutting Height Adjusting Handle Cutting Height Adjusting Handle Select the desired cutting height.
HYUNDAI 4. PRE-OPERATION CHECK These quick checks should be done each time the lawn mower is started to ensure you get the most out of your lawn mower. Set the lawn mower on a level surface and the power to OFF.
Page 31
Maximum Oil Level Minimum Oil Level HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 Reinsert the dipstick and tighten securely. NOTE Oil max. capacity: HY0343: 400 mL HY0344: 400 mL HY0345: 400 mL HY0346: 400 mL ...
HYUNDAI 4.2 CHECK THE FUEL LEVEL WARNING! Gasoline is highly flammable and explosive under certain conditions. Refuel in a well-ventilated area with the engine stopped. DO NOT smoke or allow open flames or sparks in the area where the lawn mower is being refueled or where gasoline is stored.
Page 33
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 Tighten the fuel cap securely after refilling. NOTE Only use unleaded gasoline (Pump Octane 87 or higher). NEVER use stale or contaminated gasoline, or an oil/gasoline mixture. Avoid getting dirt or water into the fuel tank.
HYUNDAI 5. STARTING THE ENGINE DANGER! Using a lawn mower indoors WILL KILL YOU IN MINUTES. Engine exhaust contains high levels of carbon monoxide (CO), a poisonous gas you cannot see or smell. If you can smell the engine exhaust you are breathing CO. Even if you cannot smell the exhaust, you could be breathing CO.
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 5.1 MANUAL RECOIL START WARNING! Ensure the lawn mower’s blade is securely fastened before starting the engine. The blade will begin to rotate as soon as the engine is started. In cold weather ONLY, push the primer bulb 1-2 times.
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 7. USING YOUR LAWN MOWER 7.1. CLEAN FLOODED ENGINE Rear Discharge If the engine won’t start after you have operated the start procedure several times, Cover Rear Discharge the engine may be flooded with excess fuel. Use following steps to clear and start a Cover flooded engine.
HYUNDAI NOTE Install the spark plug carefully by hand, to avoid cross-threading.After the plug is seated tighten 1/8 to 1/4 turn with socket spanner of spark plug to compress the washer. Release the power lever. 7.2. USING THE SELF-PROPELLED FUNCTION (HY0346, HY0348, HY0380 ONLY) The HY0346, HY0348 and HY0380 are equipped with self-propelled system.
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 7.3 USING THE SPEED LEVER (HY0348 ONLY) Once engine is running, select drive speed 1, 2 or 3, to adjust the different propelled speed. Speed Selection Lever...
HYUNDAI 7.4 EMPTYING THE GRASS BAG (HY0344, HY0345, HY0346, HY0348, HY0380 ONLY) WARNING! Before taking off the grass bag, turn off the engine and wait until the blade has come to a stop. If any grass residue is caught in the discharge chute, clean it using a brush.
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 7.5 MOWING TIPS NOTE Keep a firm grip on the upper handle with power lever and self propelled drive lever closed and walk along with it self-propelling to start mowing. Walk, NEVER run with the mower, be very careful when mowing uneven or rough ground.
HYUNDAI 8. MAINTENANCE Proper maintenance keeps your lawn mower in the best operating condition by ensuring safe, economical and trouble-free operation. Only use genuine parts and recommended fluids to replace the worn components. Improper maintenance may cause the lawn mower to malfunction and can lead to serious injury. Contact customer support if you have any maintenance questions.
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 8.1 MAINTENANCE SCHEDULE Maintain the lawn mower according to the maintenance schedule in this section. NOTE Service more frequently when used in dusty areas. These items should be serviced by an authorized service center, unless you have the proper tools and are mechanically proficient.
HYUNDAI Spark Plug Cap 8.2 CHANGING THE ENGINE OIL WARNING! Used motor oil can cause skin irritations if left in long-term contact with skin. Thoroughly wash off used oil as soon as possible with soap and water. 0.75 mm DO NOT dispose of used oil in drains or on soil. Local service (0.029 in)
Page 45
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 NOTE Oil max. capacity: HY0343: 400 mL HY0344: 400 mL HY0345: 400 mL HY0346: 400 mL HY0348: 400 mL HY0379: 400 mL HY0380: 400 mL ...
HYUNDAI 8.3 CLEANING THE AIR-FILTER WARNING! Using gasoline or other flammable solvents can cause fire or explosion. DO NOT operate this product without an air filter. DO NOT use pressurized air or solvents to clean the filter. Pressurized air can damage the filter and solvents will dissolve the filter.
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 8.4 REPLACING THE BLADE WARNING! Used motor oil can cause skin irritations if left in long-term contact with skin. Thoroughly wash off used oil as soon as possible with soap and water. Always use gloves and handle the blade with care, sharp edges could cause injury.
HYUNDAI 8.5 SPARK PLUG SERVICE NOTE DO NOT rinse spark plug in water. Follow guidelines and be careful not to overtighten the spark plug. Recommended spark plug: F6RTC Check the spark plug gap and clean the carbon deposits at the bottom of the spark plug.
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 8.6 FUEL FILTER MAINTENANCE a brush to remove carbon deposits from the ush to remove carbon deposits from the 8.7.3•••• Wipe•• t he•• f ilter•• a nd•• i nsert•• i t. k arrester . If the spark arrester is wear, rester .
Page 50
HYUNDAI Engine faults that may affect emission Any of the following faults must be repaired immediately. Consult with your authorized service centre for diagnosis and repair: Hard starting or shut down after starting. Unstable idle speed. Shut down or backfire after applying an electrical load.
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 8.8 CARBURETOR MODIFICATION FOR HIGH ALTITUDE OPERATION (ABOVE 2,000 FEET) NOTE This engine is equipped to run at altitudes below 2,000-ft. A high-altitude Main Jet is recommended when operated at 2,000 to 7,000-ft above sea level.
Page 52
HYUNDAI Carburetor Assembly Fuel Cup Seal Mixing Tube (might remain inside carburetor) Main Jet Fuel Cup Washer Drain Bolt Bolt Seal Bolt Turn off the engine. Close the fuel valve. Place a bowl under the fuel cup to catch any spilled fuel.
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 9. TRANSPORTATION & STORAGE Transporting the Lawn Mower DO NOT use the lawn mower in the vehicle. The mower should ONLY be used while in a well ventilated area. Avoid exposing the lawn mower to prolonged direct sunlight while in an enclosed vehicle.
Page 54
HYUNDAI Storage Gasoline can oxidize in as little as 30 days, causing gum and varnish to build up in fuel system components. NOTE Ensure that the storage area is free of excess humidity and dust. Drain the fuel tank and the carburetor.
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 10. TROUBLESHOOTING Problem Look for Solution Loud while running, Screws are loose. Check screws. machine vibrates Blade fasteners are Check blade fasteners. heavily. loose. Blade is unbalanced. Replace blade. Engine does not start. Start/stop lever not Press start/stop lever.
HYUNDAI 11. TECHNICAL SPECIFICATIONS HY0344 HY0343 HY0379 SPECIFICATIONS Functions Bag/Mulch/Side Mulch/Side Mulch/Side Deck Width 21 in 21 in 21 in Cutting Width 20 in 20 in 20 in Min.Cutting 1 in (25 mm) 1 in (25 mm) 1 in (25 mm) Height Max.Cutting...
Page 57
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 HY0345 HY0346 HY0380 SPECIFICATIONS Functions Bag/Mulch/Side Bag/Mulch/Side Bag/Mulch/Side Deck Width 22 in 22 in 22 in Cutting Width 21 in 21 in 21 in Min.Cutting 1 in (25 mm) 1 in (25 mm)
Page 58
HYUNDAI HY0348 SPECIFICATIONS Functions Bag/Mulch/Side Deck Width 22 in Cutting Width 21 in Min.Cutting 1 in (25 mm) Height Max.Cutting 3 in (75 mm) Height Handle Height 3-position Adjust Deck Height Single-lever, Adjust 8-position Blade Straight Number of Blades Grass catcher...
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 12. LIMITED WARRANTY This product is distributed by: Midland Power Inc. 376 Magnetic Drive, Toronto, ON M3J 2C4, Canada Warranty Beginning at the time of retail purchase and for the duration of the warranty period Midland Power Inc.
Page 60
HYUNDAI Replacement of parts made in connection with normal maintenance services including oils, adhesives, additives, fuel, filters, brushes, belts, lubricants, spark plugs, gaskets, seals, fasteners, wires, tubes, pipes, fittings, wheels, batteries, and other expendables susceptible to natural wear; g. Any accessory or attachment.
Page 61
HY0343, HY0344, HY0345, HY0346, HY0348, HY0379, HY0380 Emission Control System Warranty Parts: This list applies to parts supplied by Midland Power Inc. and does not cover parts supplied by the equipment manufacturer. Please see the original equipment manufacturer’s emissions warranty for non-Midland Power Inc. parts.
Page 62
Enjoy! Be sure to check www.hyundaipower.ca for updates regarding your product.
Page 64
For Inquiries, Please Contact: Midland Power Inc. 376 Magnetic Drive, Toronto, ON Canada M3J 2C4 1-877-528-3772 support@hyundaipower.ca www.hyundaipower.ca Imported / Distributed by Midland Power Inc., Canada Licensed by Hyundai Corporation Holdings, Korea...
Need help?
Do you have a question about the HY0343 and is the answer not in the manual?
Questions and answers