Subscribe to Our Youtube Channel
Related Manuals for Racing RAC500EHT-1
Summary of Contents for Racing RAC500EHT-1
- Page 1 ORIGINAL INSTRUCTIONS ELECTRIC HEDGE TRIMMER RAC500EHT-1 INSTRUCTION MANUAL CAUTION: Please read the instructions before using this machine BUILDER SAS 32, rue Aristide Bergès - ZI 31270 Cugnaux – France MADE IN PRC...
-
Page 2: Table Of Contents
CONTENTS SAFETY WARNINGS YOUR PRODUCT MAINTENANCE AND STORAGE DISPOSAL DECLARATION OF CONFORMITY WARRANTY PRODUCT FAILURE WARRANTY EXCLUSIONS... -
Page 3: Safety Warnings
1. SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 4 reduce dust-related hazards. 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off.
- Page 5 The manufacturer cannot be held responsible if the machine has been modified in an unauthorized manner or in such a way as to constitute a final damage. Observe the nature of the area where the work is being performed. After the machine is started, it generates toxic exhaust gases.
- Page 6 Maintain a good balance when using the tool. Stay firm feet on the ground so as not to fall. Do not lean too much, do not put yourself in positions that may unbalance and hurt you. Use the harness supplied with the tool. ...
-
Page 7: Your Product
1. Couvercle de protection de la lame Interrupteur 2. Blade 7. Porte-câble Security protection 8. Câble d’alimentation Front handle with ON/OFF switch b. Technical data Model RAC500EHT-1 Tension 230-240V~, 50Hz Power 500W Non load speed 1600min-¹ Cutting length 410mm Cutting capacity... -
Page 8: Use
3. USE a. Before cutting Make sure that the tool is properly assembled. Inspect the work area. Remove any materials or objects that may damage the tool or cause accidents. Remember that you must wear full protective equipment and keep spectators away from the work area. -
Page 9: Maintenance And Storage
4. MAINTENANCE AND STORAGE Maintain your tool regularly. This will keep your tool in good working order and extend its lifespan. Do not use abrasive, caustic agents to clean the tool. These types of products will damage your tool. Do not perform repairs by yourself. Repairs and inspection must be carried out by a competent person or at an authorized service center (please contact you service dealer). -
Page 10: Declaration Of Conformity
DECLARATION OF CONFORMITY EC Declaration of conformity BUILDER SAS 32, rue Aristide Bergès - ZI 31270 Cugnaux – France declare that the machine ELECTRIC HEDGE TRIMMER RAC500EHT-1 20210753000-20210753499 Serial number: Is in conformity with the European Directives: Machine Directive 2006/42/EC... -
Page 11: Warranty
7. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 12: Product Failure
8. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank if your product has one. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 13: Warranty Exclusions
9. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...
Need help?
Do you have a question about the RAC500EHT-1 and is the answer not in the manual?
Questions and answers