Related Manuals for Racing RACD314TB
Summary of Contents for Racing RACD314TB
- Page 1 INSTRUCTIONS ORIGINALES PETROL BRUSH CUTTER & GRASS TRIMMER RACD314TB INSTRUCTION MANUAL CAUTION : Read the instructions before using the machine !
-
Page 2: Table Of Contents
CONTENTS SECURITY WARNINGS ..........................3 YOUR PRODUCT ............................. 8 TECHNCIAL DATA…………………………………………………………………………………………………………………………………10 ASSEMBLY ............................11 FILLING OIL TANK AND FUEL TANK ......................14 OPERATION ............................15 MAINTENANCE AND STORAGE ......................18 CE DECLARATION ..........................19 WARRANTY…………………………………………………………………………………………………………………………………………..20 PRODUCT FAILURE………………………………………………………………………………………………………………………………..21 WARRANTY EXCLUSIONS………………………………………………………………………………………………………………………22... -
Page 3: Security Warnings
1. SAFETY WARNINGS Proper safety precautions must be observed. Like all power equipment this unit must be handled carefully. DO NOT EXPOSE YOURSELF OR OTHERS TO DANGER. Follow these general rules. Do not permit others to use this machine unless they are thoroughly responsible and have read, and understand the machine manual and are trained in its operation. - Page 4 Whenever approaching an operator of the machine, carefully call his attention and confirm that the operator stop the engine. Be careful not to startle or distract the operator which can cause an unsafe situation. Never touch the nylon cutting head or blade whenever the engine is running. If it is necessary to replace the protector or cutting attachment, be sure to stop the engine and confirm that the cutting device has stopped running.
- Page 5 Emission of exhaust gases National regulation can restrict the use of the machine. Never modify a trimmer or cutter in any way. Improper use of the machine can cause SERIOUS OR FATAL PERSONAL INJURY. The engine exhaust form this product contains chemicals to cause cancer, birth defects, of other reproductive harm.
- Page 6 Wear protective equipment: hearing protection, eye protection, and helmet Wear protection gloves Wear protective footwear Caution to exhaust gases Do not smoke and do use the tool near naked flame The accessible part are hot when operate the tool Caution! Risk of rebound Keep bystanders away at least 15mm Caution! The tool can contact to a voluminous material.
- Page 7 Be careful of the cutting attachment! Residual risks Even if you use this tool correctly, there are always residual risks. The following hazards may arise in connection with the structure and manufacture of this power tool: Hearing impairment if no suitable hearing protection is worn. Cuts if no suitable protective clothing is worn.
-
Page 8: Your Product
2. YOUR PRODUCT a. Description 1. Air filter 2. Fuel tank 3. Oil tank 4. Recoil starter 5. Harness 6. Oil cup 7. 3 teethes blade 8. Wrench 9. Metal lock pin/ wrench 10. Nylon cutting head... - Page 9 11. Bar assembly 12. Bracket (handle part support) 13. Handle 14. Handle with throttle trigger, ON/OFF switch and throttle trigger lockout 15. Angle drive 16. Carter of protection 17. Cutting line device...
-
Page 10: Techncial Data
3. TECHNICAL DATA Engine displacement 31cm³ Maximum engine speed Brush cutter: 9300min-¹ Grass trimmer: 8000min-¹ Maximum power 0,7kW Mass Empty tank: 7,3kg Empty tank with specified attachment: 8kg Full tank and specified attachment: 8,5kg Volume of fuel tank 0,7l 0,08l Volume of oil tank Cutting diameter Grass trimmer: 480mm... -
Page 11: Assembly
4. ASSEMBLY a) Installation of the tube on the tool Unscrew the bolt (1) and remove the screw cap (2). See Fig 1. Insert the attachment into the connector (Fig 2). Make sure to fix the pin into the hole of the tube. Put back the screw cap (2) and screw the bolt on it (3). See Fig 3. - Page 12 c) Installation of the carter of protection Remove the screws which are on the carter of protection (fig7). Install the tube on the carter of protection. Make sure that you have installed it in the correct position (Fig Screw the carter on the tube with the two screws (Fig 9). d) Installation of the nylon cutting head (for grass trimmer operation) Insert a metal locking tool into the hole on the side of the drive gear and on the tool drive (Fig 10).
- Page 13 e) Installation of metal blade (for brush cutter operation) Insert a metal locking tool into the hole on the side of the drive gear and on the tool drive (Fig 10). Remove cover bell and the holding nut from the shaft (Fig 11). Install, in the following order, on the shaft: the blade, the cover bell and then the holding nut (Fig 13).
-
Page 14: Filling Oil Tank And Fuel Tank
5. FILLING OIL TANK AND FUEL TANK a) Fuel Warning: Gasoline is highly flammable. Keep the fuel in specially designed cans. Only fill the tank outside and do not smoke during the operation. Avoid sparks or open flames near the fuel. ... -
Page 15: Operation
b) Oil Open the oil tank. By using the provided container, pour the oil in the tank. Do not overfill. Close the tank. Wipe off all overfill oil. Information Recommended oil: We recommend the use of high quality detergent oil classified for SF, SG, SH, SJ or higher. - Page 16 Stopping the tool Release the throttle trigger and the throttle trigger lockout. Move the ON/OFF switch to STOP position (O). Grass trimmer operation Trimming Tilt the head slowly to direct debris away from you. If cutting up to a barrier such as fence, wall or tree, approach from an angle where any debris ricocheting off the barrier will fly away from you, Move the line head slowly until the grass is cut right up the barrier, but do not jam (overfeed) the line into the barrier.
- Page 17 Brushcutter operation Do not the brushcutter for cutting trees Do not cut with dull, cracked or damaged meal blade. Before cutting growth, inspect for obstructions such as boulders, metal stakes or strands of wire from broken fences. If an obstruction cannot be removed, mark its location so that you can avoid it with the blade.
-
Page 18: Maintenance And Storage
7. MAINTENANCE AND STORAGE a) Air filter Accumulated dust in the air filter will reduce engine efficiency. Increase fuel consumption and allow abrasive particles to pass into the engine. Remove the air filter as often as necessary to maintain in a clean condition. -
Page 19: Ce Declaration
ZI, 32, rue Aristide Bergès – 31270 Cugnaux - France Tel : +33 (0)5.34.502.502 Fax : +33 (0)5.34.502.503 declares that the machine: PETROL BRUSH CUTTER & GRASS TRIMMER RACD314TB Serial No: 20211189050-20211189433 the people name holding the technical file：Mr. Olivier Patriarca... -
Page 20: Warranty
9. WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 21: Product Failure
10. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: • Empty the fuel tank. • Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 22: Warranty Exclusions
11. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •... - Page 24 BUILDER SAS 32, rue Aristide Bergès - ZI 31270 Cugnaux – France Made in PRC 2021...
Need help?
Do you have a question about the RACD314TB and is the answer not in the manual?
Questions and answers