Fab Fours AERO D3271 Installation Instructions Manual

2015+ ford f150

Advertisement

Your safety and the safety of others is very important.
In order to help you make informed decisions about safety, we have provided
installation instructions and other information.
These instructions alert you to potential hazards that could hurt you or others.
Please do a job safety analysis before each task to identify potential hazards for your
situation and remove/protect against them.
You must use your own good judgment, and take your time.
Read and understand all safety precautions and instructions before installing this product.
THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR
INSTALLATION AND USE RESTS WITH THE OWNER.
CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY
Failure to observe these instructions could lead to severe injury or death.
Always remove jewelry and wear eye protection.
Always use extreme caution when jacking up a vehicle for work. Set
emergency brake and use tire blocks. Locate and use the vehicle
manufacturers designated lifting points. Use jack stands.
Always use appropriate and adequate care in lifting components into place.
Always insure components will remain secure during installation and
operation.
Always wear safety glasses when installing this kit. A drilling operation will
cause flying metal chips. Flying chips can cause serious eye injury.
Always use extreme caution when drilling on a vehicle. Thoroughly inspect
the area to be drilled (on both sides of material) prior to drilling, and
relocate any objects that may be damaged.
Always use extreme caution when cutting and trimming during fitting.
Always tighten all nuts and bolts securely per installation instructions.
Always route electrical cables carefully. Avoid moving parts, components
that become hot and rough or sharp edges.
Always insulate and protect all exposed wiring and electrical terminals.
 Always perform regular inspections and maintenance on mounts and
related hardware.
Copyright 2008 Fab Fours, Inc.
Installation Instructions
Ford F150 AERO Front
SAFETY
OR EQUIPMENT DAMAGE.
Injury hazard
Page 1 of 9
Product Number: D3271, D3272
Application: 2015+ Ford F150
D327X_REV_A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AERO D3271 and is the answer not in the manual?

Questions and answers

Summary of Contents for Fab Fours AERO D3271

  • Page 1   Always insulate and protect all exposed wiring and electrical terminals.  Always perform regular inspections and maintenance on mounts and  related hardware. Page 1 of 9 D327X_REV_A Copyright 2008 Fab Fours, Inc.
  • Page 2 Your front bumper designed in 3-D from digitized data, CNC laser cut, fabricated, and powder coated… all in the U.S.A. Enjoy the fit and finish of a quality AERO Ford F150 Front Bumper from Fab Fours Inc. Page 2 of 9 D327X_REV_A Copyright 2008 Fab Fours, Inc.
  • Page 3: Parts List

    Note: Save all OEM parts until installation is complete! A. Using a flathead screwdriver, carefully remove center plastic piece, indicated by oval in the center of the OE bumper. Figure 1a Page 3 of 9 D327X_REV_A Copyright 2008 Fab Fours, Inc.
  • Page 4 (ref. fig. 2c). If front OEM bumper contains sonar (ref. fig. 2b), remove four bolts with 11 mm. If your bumper includes a sonar device, remove it now using an E6 External socket. Unplug the device. Figure 2a Figure 2b Page 4 of 9 D327X_REV_A Copyright 2008 Fab Fours, Inc.
  • Page 5 E. Slide out both nut strips from the frame channel when done. If your vehicle model includes a louver system for the intercooler located between the frame mounts, the shroud must be removed. Special care must Page 5 of 9 D327X_REV_A Copyright 2008 Fab Fours, Inc.
  • Page 6 Figure 4 (Louver w/ shroud cut away at base) Page 6 of 9 D327X_REV_A Copyright 2008 Fab Fours, Inc.
  • Page 7: Pre-Installation

    If you are installing aftermarket lights, do the wiring for those now and install them into the bumper. (But don’t plug them in until after bumper install) Page 7 of 9 D327X_REV_A Copyright 2008 Fab Fours, Inc.
  • Page 8: Front Bumper Installation

    There will be 6 bolts. The nut plates can be installed by going over the frame as shown below. Adjust the height of the bumper to the truck and tighten the bolts. (Fab Fours recommends 1/4 profile gap as a standard.) Enjoy your new Aero Front Bumper from Fab Fours! Page 8 of 9 D327X_REV_A Copyright 2008 Fab Fours, Inc.
  • Page 9: Maintenance & Care

     After washing of the vehicle make sure to fully dry all surfaces  Contact Information Fab Fours Inc. Phone (866)-385-1905 2213 Industrial Park Drive (866)-574-1424 Lancaster, SC 29720 Email Support@fabfours.com More than expected… Better than expected Page 9 of 9 D327X_REV_A Copyright 2008 Fab Fours, Inc.

This manual is also suitable for:

Aero d3272Aero ff15-d3271-1

Table of Contents