Table of Contents
Advertisement
Quick Links
Your safety and the safety of others is very important.
In order to help you make informed decisions about safety, we have provided
installation instructions and other information.
These instructions alert you to potential hazards that could hurt you or others.
Please do a job safety analysis before each task to identify potential hazards for your
situation and remove/protect against them.
You must use your own good judgment, and take your time.
Read and understand all safety precautions and instructions before installing this product.
THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR
INSTALLATION AND USE RESTS WITH THE OWNER.
CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY
Failure to observe these instructions could lead to severe injury or death.
Always remove jewelry and wear eye protection.
Always use extreme caution when jacking up a vehicle for work. Set
emergency brake and use tire blocks. Locate and use the vehicle
manufacturers designated lifting points. Use jack stands.
Always use appropriate and adequate care in lifting components into place.
Always insure components will remain secure during installation and
operation.
Always wear safety glasses when installing this kit. A drilling operation will
cause flying metal chips. Flying chips can cause serious eye injury.
Always use extreme caution when drilling on a vehicle. Thoroughly inspect
the area to be drilled (on both sides of material) prior to drilling, and
relocate any objects that may be damaged.
Always use extreme caution when cutting and trimming during fitting.
Always tighten all nuts and bolts securely per installation instructions.
Always route electrical cables carefully. Avoid moving parts, components
that become hot and rough or sharp edges.
Always insulate and protect all exposed wiring and electrical terminals.
Always perform regular inspections and maintenance on mounts and
related hardware.
Installation Instructions
Ford Raptor Vengeance Front
SAFETY
OR EQUIPMENT DAMAGE.
Injury hazard
Page 1 of 9
Product Number: D4351, D4352
Application: 2017+ Ford Raptor
Advertisement
Table of Contents
Related Manuals for Fab Fours D4351
Summary of Contents for Fab Fours D4351
- Page 1 Installation Instructions Ford Raptor Vengeance Front Product Number: D4351, D4352 Application: 2017+ Ford Raptor SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information.
- Page 2 Installation Instructions Ford Raptor Vengeance Front Product Number: D4351, D4352 Application: 2017+ Ford Raptor Overview Congratulations on your new purchase of the industries’ best and most stylish front bumper available for the 2017 Ford Raptor. This bumper has been designed to be lightweight and easily customized with the industry’s highest quality accessories.
-
Page 3: Parts List
Installation Instructions Ford Raptor Vengeance Front Product Number: D4351, D4352 Application: 2017+ Ford Raptor Parts List D435X replacement bumper 50013-HW fastener kit Instruction manual Tools Required Socket wrench with extension (ratcheting wrenches may also be convenient) ... - Page 4 Installation Instructions Ford Raptor Vengeance Front Product Number: D4351, D4352 Application: 2017+ Ford Raptor B. Using a flathead screwdriver, carefully remove center plastic piece, indicated by oval in the center of the OE bumper. Figure 1a Figure 1b C. Using 21 mm socket, remove the three nuts per side, two are located under the plastic center piece (ref.
- Page 5 Installation Instructions Ford Raptor Vengeance Front Product Number: D4351, D4352 Application: 2017+ Ford Raptor Figure 2a Figure 2b Figure 2c D. Remove two 8mm bolts one per side that hold on the bumper side support bars from the truck side leaving the support bars attached to the bumper.
- Page 6 Installation Instructions Ford Raptor Vengeance Front Product Number: D4351, D4352 Application: 2017+ Ford Raptor If your vehicle model includes a louver system for the intercooler located between the frame mounts, the shroud must be removed. Special care must be taken not to damage louvers when cutting around the base of the rectangular shroud, a cut off wheel is recommended.
-
Page 7: Pre-Installation
Installation Instructions Ford Raptor Vengeance Front Product Number: D4351, D4352 Application: 2017+ Ford Raptor III. Pre-Installation NOTE: The following installation steps apply to the installation of the front bumper. PLEASE READ THE ENTIRE MANUAL BEFORE ATEMPTING INSTALLATION. Ignoring these steps will increase your probability of scratching the vehicle during product installation. -
Page 8: Front Bumper Installation
There will be 6 bolts. Adjust the height of the bumper to the truck and tighten the bolts. (Fab Fours recommends 1/4 profile gap as a standard.) Re-install factory skid plate using OEM hardware, and supplied spacers if necessary to ensure the skid plate is not rubbing the bumper. -
Page 9: Maintenance & Care
Installation Instructions Ford Raptor Vengeance Front Product Number: D4351, D4352 Application: 2017+ Ford Raptor Maintenance/Care Periodically check and tighten all fasteners. Stripped, fractured, or bent bolts or nuts need to be replaced. After washing of the vehicle make sure to fully dry all surfaces ...