Table of Contents
Advertisement
Quick Links
Your safety and the safety of others is very important.
In order to help you make informed decisions about safety, we have provided
installation instructions and other information.
These instructions alert you to potential hazards that could hurt you or others.
Please do a job safety analysis before each task to identify potential hazards for your
situation and remove/protect against them.
You must use your own good judgment, and take your time.
Read and understand all safety precautions and instructions before installing this product.
THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR
INSTALLATION AND USE RESTS WITH THE OWNER.
CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY
Failure to observe these instructions could lead to severe injury or death.
Always remove jewelry and wear eye protection.
Always use extreme caution when jacking up a vehicle for work. Set
emergency brake and use tire blocks. Locate and use the vehicle
manufacturers designated lifting points. Use jack stands.
Always use appropriate and adequate care in lifting components into place.
Always insure components will remain secure during installation and
operation.
Always wear safety glasses when installing this kit. A drilling operation will
cause flying metal chips. Flying chips can cause serious eye injury.
Always use extreme caution when drilling on a vehicle. Thoroughly inspect
the area to be drilled (on both sides of material) prior to drilling, and
relocate any objects that may be damaged.
Always use extreme caution when cutting and trimming during fitting.
Always tighten all nuts and bolts securely per installation instructions.
Always route electrical cables carefully. Avoid moving parts, components
that become hot and rough or sharp edges.
Always insulate and protect all exposed wiring and electrical terminals.
Always perform regular inspections and maintenance on mounts and
related hardware.
Copyright 2008 Fab Fours, Inc.
Installation Instructions
Ford F150 Premium Front Bumper
Product Number: H4550, H4551, H4552
SAFETY
OR EQUIPMENT DAMAGE.
Injury hazard
Page 1 of 12
Application: 2018+ Ford F150
H455X_REV_A
Advertisement
Table of Contents
Related Manuals for Fab Fours H4550
Summary of Contents for Fab Fours H4550
- Page 1 Installation Instructions Ford F150 Premium Front Bumper Product Number: H4550, H4551, H4552 Application: 2018+ Ford F150 SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information.
- Page 2 Your front bumper designed in 3-D from digitized data, CNC laser cut, fabricated, and powder coated… all in the U.S.A. Enjoy the fit and finish of a quality Ford F150 Front Bumper from Fab Fours Inc. Page 2 of 12 H455X_REV_A Copyright 2008 Fab Fours, Inc.
-
Page 3: Parts List
Installation Instructions Ford F150 Premium Front Bumper Product Number: H4550, H4551, H4552 Application: 2018+ Ford F150 Parts List H455X replacement bumper and brackets 50012-HW fastener kit HDLA-HW 4 Stud plates Light kitting [i.e. 20090(2), 61349(2), 61350(2)] ... - Page 4 Installation Instructions Ford F150 Premium Front Bumper Product Number: H4550, H4551, H4552 Application: 2018+ Ford F150 Figure 1b B. Using 21 mm socket, remove the three nuts per side, two are located under the plastic center piece (ref. fig. 2a-b) and the third accessible from the back of the frame (ref.
- Page 5 Installation Instructions Ford F150 Premium Front Bumper Product Number: H4550, H4551, H4552 Application: 2018+ Ford F150 Figure 2c C. To remove the electrical harness, unplug fog light and remove one (1) Christmas tree plug on each side. At this time, carefully pull away bumper checking to make sure nothing is still connected.
- Page 6 Installation Instructions Ford F150 Premium Front Bumper Product Number: H4550, H4551, H4552 Application: 2018+ Ford F150 Carefully pry clips (see red arrows below) around exterior of louver box outward and pull shroud. Figure 4a (Removing shroud from louvers) ...
-
Page 7: Pre-Installation
Installation Instructions Ford F150 Premium Front Bumper Product Number: H4550, H4551, H4552 Application: 2018+ Ford F150 III. Pre-Installation NOTE: The following installation steps apply to the installation of the front bumper. PLEASE READ THE ENTIRE MANUAL BEFORE ATEMPTING INSTALLATION. Ignoring these steps will increase your probability of scratching the vehicle during product installation. -
Page 8: Front Bumper Installation
Installation Instructions Ford F150 Premium Front Bumper Product Number: H4550, H4551, H4552 Application: 2018+ Ford F150 Figure W-TS-1 Figure W-TS-2 Optional: If installing winch and roller fairlead into bumper, do it at this time. Follow the winch manufacturer’s instructions for installation. If you are installing a winch with a pulling capacity of 12,000 lbs., the front face mounting holes must be... - Page 9 Installation Instructions Ford F150 Premium Front Bumper Product Number: H4550, H4551, H4552 Application: 2018+ Ford F150 Mount bracket to bumper. With the help of at least two others, and possibly a floor jack, to support the center of the bumper, lift the Fab Fours bumper into place.
- Page 10 Product Number: H4550, H4551, H4552 Application: 2018+ Ford F150 Figure 7 Install the Fab Fours fog lights onto the mounting brackets as shown below using the #8 button head screws, washers, and hex nuts. Figure 8 Install the fog light and bracket into the bumper using the remaining two holes available in the light insert.
- Page 11 Product Number: H4550, H4551, H4552 Application: 2018+ Ford F150 Figure 9 Secure OEM electrical harness to the Fab Fours bumper. Repeat steps G through K for other side. Enjoy your new rear rreplacement bumper from Fab Fours! Page 11 of 12 H455X_REV_A Copyright 2008 Fab Fours, Inc.
-
Page 12: Contact Information
Installation Instructions Ford F150 Premium Front Bumper Product Number: H4550, H4551, H4552 Application: 2018+ Ford F150 Maintenance/Care Periodically check and tighten all fasteners. Stripped, fractured, or bent bolts or nuts need to be replaced. After washing of the vehicle make sure to fully dry all surfaces ...