Advertisement
Advertisement
Table of Contents
Related Manuals for Kaadas KA252-Z
Summary of Contents for Kaadas KA252-Z
- Page 1 Z-Wave Smart Lock KA252-Z Installation Guide Kaadas...
- Page 3 Before installing the lock, check door jamb and door preparation.
-
Page 7: Mounting Plate
Keys (2) Latch Screws (2) Strike Plate Screws (4) Strike Plate Reinforcement Plate Mounting Plate (Optional) Mounting Plate Screws (2) Interior Assembly Screws (3) Drive-In Collar Z-Wave Module (Optional) - Page 8 1-1/2" or 2-1/8" (38 or 54mm) " Measure to confirm that the bore hole is 1-1/2 " or 2-1/8 (38mm or 54mm). " to 2" (35mm to 50mm) thick.
- Page 9 2. Adjust the latch Determine backset and adjust the latch. Hold the latch in front of the bore hole with the latch face flush against the door edge. Is the slotted hole centered in the door hole?
-
Page 10: Install Latch
3. Install Latch 4. Install strike on the door frame. IMPORTANT: Make sure the hole in the door frame is drilled a minimum of 1"(25mm) deep. - Page 11 Measure the diameter of the hole in the door. 1-1/2" (38mm) 1-1/2" or 2-1/8" Remove the spacer (38 or 54mm) 2-1/8" (54mm) Proceed to next step...
- Page 12 Tailpiece Latch tailpiece. Secure the mounting plate with the mounting plate screws.
- Page 13 Tailpiece Rotate the thumb turn into the vertical Remove the battery cover. Connect the cable from position. Insert the tailpiece horizontally the exterior assembly to the socket on the interior into the interior assembly. assembly. Push the connector in firmly to ensure a proper connection.
- Page 14 7. Door handing and reset Reset Button Reset Tool Use the Reset Tool to press and hold the Reset With the device unlocked, inset 4 AA alkaline Button for more than 5 seconds until you hear a batteries into the battery pack. long “BEEP”.
-
Page 15: Programming Guide
Z-Wave Smart Lock KA252-Z Programming Guide Kaadas... - Page 16 Information and safety warnings...
- Page 17 that you change the Master PIN Code to a code of your own before programming the lock. Lasts up to seven months Batteries NOTE: only use new, non- rechargeable batteries. Exterior Assembly Interior Assembly Battery Cover Multi-function Button Keypad Fingerprint Sensor Reset Button Key Cylinder Indicator Light...
-
Page 18: Vacation Mode
Master PIN code: Vacation Mode: Required for programming and feature settings, the This is a safety feature for you when you leave your house Master PIN Code can be used to unlock the door while for vacation or a long trip. When you activate Away Mode, in vacation mode. - Page 19 Z-Wave Master Master PIN Code Mode...
- Page 20 Settings Factory Defaut Master PIN Code 12345678 Auto Lock Disabled Silent Mode Disabled Wrong Code Entry Limit 10 times Shutdown Time 3 Minutes Vacation Mode Disabled Press and hold the Reset Button with the Reset Tool for 5 seconds until you hear the "BEEP". The thumb turn cannot rotate.
-
Page 21: Fcc Statement
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. - Page 22 ISED Statement English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
- Page 23 Quick Set Up The default Master Code is 12345678 . It is required that you If the indicator light flashes red, your setting failed and you will need to change it to a code of your own before programming. redo the operation. Change Master New Master New Master...
Need help?
Do you have a question about the KA252-Z and is the answer not in the manual?
Questions and answers