Kaadas R8-5KD User Manual

R8-5KD
User Manual
www.kaadasgroup.com
Shenzhen Kaadas Intelligent Technology Co., Ltd reserves all rights
for the final interpretation to this user manual
All design and specifications are subject to change without notice.
1

Components

Inside escutcheon Outside escutcheon Inside Mounting Plate
6
X3
Flat Head Screws M5*40mm Mounting Screws
(Door Thinckness 40-50mm) M4*6mm
4

Installation

1. Get the front escutcheon cable through the drill
hole on the door.
3. According to the actual installation height of the
lock, select the number of strike shims to be
installed, and fix them together with the strike.
After installing the strike,secure the strike cover
with the 2 mounting screws.
5. Get the inside escutcheon on the bracket and
fix screws.
5

Warning

* Read and understand all instructions before you use your product.
* Warranty does not apply if damage was caused by failure to follow instructions.
* Only use the alkaline batteries.
* Do not expose the product and accessories to rain or water.
* Do not expose the product to corrosive substances so as not to damage the protective cover.
* Do not scrape the fingerprint sensor with sharp objects, otherwise it may cause permanent damage.
* When cleaning the product, please wipe with a soft cloth.
* If there is a low battery alert, please replace all the batteries in time and make sure they are properly installed.
Strike Strike shim Strike shims Strike cover
X3 X6
Flat Head Screws M5*30mm Wood Combination screws
(Door Thinckness 30-40mm) ST4*20mm
2. Get the front escutcheon cable through the
inside mounting plate and fix screws from
inside of the door.
* Be careful not damage
the connecting cable
4. Get the outside escutcheon cable connected
to the inside escutcheon.
6. Fix battery cover screws after insert 4AA
batteries and test functions.
2
Specifications
Touch screen keypad
Card reader area
Fingerprint sensor
Type C USB emergency
power supply
7 2.3 mm
14 .1mm
Outside escutcheon
1. You can operate following the voice guide by multi-language
(Chinese/English/Spanish/Portuguese/ Russian).
2. Master PIN Code(6~12 digit): Default master PIN code is "12
345678", please modify it after installation.
3. User PIN Code(6~12 digit): Maximum capacity is 10 with user
number [00-09].
3

Preparing for Installation

1.Check whether the door is left handed or right handed before installation.
left handed door
Outside
2.Comfirm inside escutcheon installation direction.
left handed door right handed door
Inside Inside
6
Definitions
Master Mode:
The Master Mode could be entered by entering "#+Master PIN Code+#" to programming the lock.
Master PIN code:
The Master PIN Code is used for unlock, programming and setting feature. The default Master PIN code[12345678] is
required to be changed immediately after enter the menu at the first time.
Auto Re-lock:
After unlocking successful by PIN Code/Card/Fingerprint/APP, it will automatically lock in auto re-lock mode once the door is
closed.
One-Time PIN Code:
This code can only be used once and will be automatically deleted after using.
Manual Mode:
Auto re-lock mode could be adjusted to Manual Mode. In Manual Mode the lock could be locked by verifying user
code/fingerprint/card from outside.
Silent Mode:
Enabling Silent Mode shuts off the code confirmation tone playback for use in quiet areas. Silent mode is selected in the
voice setting of Master Mode.
Status LED:
Located on outside escutcheon.
Lockout Mode:
When wrong user PIN code/card/fingerprint for 5 times,the system will lock down for 3 minutes.
After that the lock will activate again. while the lock is lock down, the system will alarm when you are trying to use keypad.
Away Mode:
It is a security feature when you are leaving home for vacation or a long trip. If the lock is unlocked by the key or by the
thumbturn in away mode, the lock will sound an alarm.
Dual-verification Mode:
Any combination of fingerprint, PIN code and card can be flexibly used.
Reset button:
After reset operation, the lock will be restored to factory default settings, all user credentials will be deleted. Refer to reset guide.
7

Menu Table

Press[1] Modify Master PIN code
1. Add User PIN Code
2. Add Temporary PIN Card
Press[2]
3. Add Fingerprint
4. Add User Card
1.Modify Master PIN code
1. Delete User PIN Code
2.User Setting
2. Delete Temporary PIN Card
Press[3]
3.Delete Users
3. Delete Fingerprint
4. Delete User Card
4. System Setting
5. Extended Function
1. Language Setting
6. System Query Press[4] 2. Volume Setting
3. Opening Mode Setting
7. Bluetooth Setting
1. Join the Remote Network
Press[5]
2. Exit the Remote Network
1. Query Serial Number
Press[6]
2. Query Firmware Version
1. Enable Bluetooth
Press[7]
Battery cover
Auto-Relock mode
and manual mode
switch
Dead bolt
Fingerprint sensor
6 9 m m 77 .3mm
Inside escutcheon
4. Temporary user PIN code (6-12 digit): there is only one
temporary user PIN code.
5. Card: Maximum capacity is 100 with user number [00-99].
6. Fingerprint: Maximum capacity is 20 with user number
[00-19].
Outside right handed door
3.Based on door type and direction, match and
hold installation template on door tightly and
drill a hole on door.
Edge the door
left handed door right handed door
1. For adding front lock fingerprint
2. For adding rear lock fingerprint
1. Delete a Single User PIN Code
2. Delete Codes
1. For deleting front lock fingerprint
2. For deleting rear lock fingerprint
1. Delete a Single User Card
2. Delete Cards
1. Chines 2. English 3. Portuguese
4. Spanish 5. Russian
1. High Volume 2. Low Volume
3. Silent mode
1. Single -verification Mode
2. Dual-verification Mode