Subscribe to Our Youtube Channel
Related Manuals for KRESS KC241 Series
Summary of Contents for KRESS KC241 Series
- Page 1 SAFETY AND OPERATING MANUAL Pole Hedge Trimmers KC240 KC240.X KC241 KC241.X KC270 KC270.X...
-
Page 3: Table Of Contents
Customer Service Team for assistance. We are confident you will enjoy working with your Kress product for years to come. INTENDED USE This machine is intended for cutting and trimming hedges and bushes in light and heavy commercial use. -
Page 4: Component List
KC270 KC270.X KC241 KC241.X KC240 KC240.X COMPONENT LIST BATTERY-RELEASE BUTTON BATTERY PACK * REAR IMPACT GUARD SPEED CONTROL BUTTON ON/OFF SWITCH SHOULDER STRAP MOUNT THROTTLE TRIGGER ARTICULATING GEAR CASE (THE ANGLE CAN BE ADJUSTED) BLADE SAFETY LOCK OFF LEVER FIXED GEAR CASE (THE ANGLE CANNOT BE ADJUSTED) FRONT HANDLE BLADE SHEATH SHOULDER STRAP... -
Page 5: Product Safety
PRODUCT SAFETY tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol GENERAL POWER TOOL or medication. A moment of inattention while operating power tools may result in serious SAFETY WARNINGS personal injury. b) Use personal protective equipment. - Page 6 the power tool repaired before use. Many HEDGE TRIMMER SAFETY accidents are caused by poorly maintained WARNINGS power tools. f) Keep cutting tools sharp and clean. Properly a) Keep all parts of the body away from the maintained cutting tools with sharp cutting edges blade.
- Page 7 To reduce the risk of injury, user performance. must read instruction manual k) Recharge only with the charger specified by Kress. Do not use any charger other than that specifically provided for use with the equipment. Warning l) Do not use any battery pack which is not designed for use with the equipment.
-
Page 8: Assembly & Operation
Use with model KAC840 battery Wear dust mask charger, See instruction manual for additional battery chargers. KAC840 Wear head protection RCM marking ABN: Australian Business Number. By this Wear protective gloves number, business information such as entity type, status, business location etc. can be found at website http://abr.business.gov.au. - Page 9 Attach the cutting attachment to the pole, making sure that the cutting attachment completely covers the white part of the label. Tighten the screws. NOTE: Please keep the blade vertically facing upwards. Assembling the (See Rear Handle Assembly Fig. A4) Connecting the hedge trimmer to the backpack harness (Not supplied) (See Fig.
- Page 10 Before usage, remove the Blade Sheath first. (See Fig. B7) Installing & removing the battery pack (See Fig. B8) Adjust the blade angle (See Fig. B6) WARNING! Please remove battery pack before adjusting the blade angle. WARNING! Please keep the blade sheath 1.
- Page 11 Choosing speed (See Fig. D) Side cutting (See Fig. F2, F3) 1. Press the On/Off switch. 2. Press the Speed Control Button to choose the speed you need. If it is necessary to cut at a certain distance from the hedge (flowerbed): set the cutting attachment at the appropriate angle.
-
Page 12: Transportation
Cutting overhead (See Fig. F4) 0°~10° Hold the hedge trimmer vertically and swing it in an arc for maximum Working distance. WARNING: Working at heights above shoulder level can be tiring. To reduce the risk of injury due to fatigue, avoiding placing the rear hand on a control handle higher than shoulder height. -
Page 13: Maintenance
secure and position it to prevent movement or damage. Transporting the battery 1. Ensure the battery is in a safe condition. 2. Use non-conductive packaging when transporting the battery. 3. The contained Li-Ion batteries are subject to the dangerous goods legislation requirements. Transport batteries only when the battery housing is undamaged. -
Page 14: Cleaning
cutting edge. Only sharpen the cutting edge. Do not grind blunt projecting parts of the cutting blade or its guard. Use a whetstone to remove burr from cutting edge. After sharpening, clean away the dust from the blade in a safe manner. -
Page 15: Technical Data
Red error LED flashing Overload. The cutting attachment is jammed, deactivate the product and then lower machine for remove. Remove the battery. Clean the cutting attachment from unwanted materials. Temperature issue. Let the product cool down. Other problems Contact Service Agent. The product does not start Deris in the battery Clean the battery connectors with... - Page 16 SUGGESTED BATTERIES AND CHARGERS Battery Capacity Charger Amperage KAC804 4.0 Ah KAC810 KAC840 30 A (With Backpack Harness 11.0 Ah and Weight Kit) We recommend that you purchase your accessories from the same Dealer that sold you the tool. Refer to the accessory packaging for further details.
Need help?
Do you have a question about the KC241 Series and is the answer not in the manual?
Questions and answers