HENDI 221105 - CENTRIFUGAL JUICE EXTRACTOR Manual

Technical specifications

Remark: Technical specification is subjected to change without prior notification.

Main parts of the product

(Fig.1)

1. Pusher
2. Lid with feeding chute
3. Cutting blade at the bottom
4. Basket assembly
5. Flange
6. Bowl
7. Spout assembly
8. Safety arm
9. Motor unit
10. Feeding chute
11. Ejector
12. Handles
13. Sieve
14. Pulp container
15. Suction feet

Note: Three stoppers for the spout assembly are supplied to prevent the insects from entering.

Remark: The content of this manual applies for all listed items unless specified otherwise. The appearance may vary from the shown illustrations

Circuit diagram

(Fig.2)

A: Off
B: On
C: White
D: Black
E: Red
F: Blue
G: Brown
EP: Main phase
EA: Starting phase
CD: Starting capacitor
KD: Starting relay
KW: Electromagnetic relay
MA1: Start switch
MA2: Stop switch
SW: Clamp safety switch
MF: Breaking module
MO: Single phase Motor
PTO: Motor thermal protector

Preparation before use

• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all accessories. In case of incomplete or damaged delivery, please contact the supplier immediately. In this case, do not use the device.
• Clean the accessories and the appliance before use (See == > Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in the future.
• Keep the user manual for future reference.

NOTE! Due to manufacturing residues, the appliance may emit a light odor during the first few uses. This is normal and does not indicate any defect or hazard. Make sure the appliance is well ventilated.

Installation / Assembly & Disassembly

• WARNING! Never connect the power plug into an electrical outlet before the appliance is fully assembled.
• Make sure the spout assembly is closed.
  1. Position the motor unit firmly so that the OFF/ON buttons are facing you. (Fig.3)
     
  2. Place the bowl on top of the motor unit. (Fig.4)
     
  3. Fit the flange onto the rim of the bowl. The ribs of the flange should be lined up with the flat panel of the bowl. Make sure that the flange is correctly fitted. (Fig.5)
     
  4. Lower the basket assembly into correct place, holding it by the holders. Rotate it until its slots into correct place. (Fig.6)
     
  5. Line the lid with feeding chute with the notches in the flange. (Fig.7)
     

Make sure that the pin on the motor shaft is correctly lined up with the corresponding notch in the basket hub. (Fig.8)

6. Correctly fit the pulp container with the hopper plate. (Fig.9)
   
7. Close the safety arm correctly.
   The juicer will not start unless the safety arm has been closed properly (safety switch). (Fig.10)
   
8. Now, the appliance is assembled and ready for use.

Operating instructions

NOTES

• Do not put your hand or fingers into the feeding chute to push food or remove clogged food. Use the pusher only. Danger of serious injury due to the rotating blade.
• Close the safety arm to operate.
• Always switch "OFF" the appliance and unplug it when not in use.
• Check regularly the flange and lid are correctly fitted especially when change to another food.

Preparing fruits and vegetables

• This juicer can be used to make juices from many different types of fruit and vegetables, but some preparations are needed to create flavorful and tasty juices.
• Rinse fruits under fresh running water.
• Cut large fruit into small pieces that fit into the feeding chute.
• R emove large seeds, stones, ad pits from cherries, peaches, etc.
• Peel thick-skinned fruits (pineapples, oranges, melons, etc).
• Some foods are not suitable for processing in a juicer, due to their hard consistency (e.g. Coconuts).

NOTE: Never put ice cubes or frozen fruit in the feed tube.

Extracting juice

• Place a container (not supplied) under the spout assembly with the spout open.
• Remove the pusher from the feeding chute.
• Connect the power plug to a suitable electrical supply outlet.
• Switch ON the appliance by pressing the "ON" (green) button.
• Fill the prepared ingredients into the hopper plate gradually. Do not overload it. Add small pieces at a time. Fruit pulp is ejected into the pulp container while the extracted juice flows through the spout into the container (not supplied).
• Use the pusher to push & guide the ingredients through the lid with feeding chute.
• Press the "OFF" button when all the food has been processed.

Safety protection

• This juicer will not start unless the lid with feeding chute has been correctly positioned and the safety arm locked properly.
  The motor will be switched to OFF as soon as you unlock the safety arm or press the OFF button.
• This juicer is equipped with a powerful brake which will stop the appliance in less than few seconds if you unlock the safety arm while the juicer is running.
• To switch your juicer ON again, simply lock the safety arm properly over the lid and press the I (ON) button.

Removing clogged foodstuff from lid with feeding chute

• If food is clogged, use the pusher to push it down. If this fails to work, press the switch to the "OFF" position and wait a while until the blade stops runnings.
• Disconnect the power plug from the electrical supply outlet and remove the lid with feeding chute.
• Wait until the juicer has come to a complete standstill and has fully cooled before disassembling.
• Clear all clogged foodstuff off the lid with feeding chute.

Operation tips

• Do not put any fruit or vegetables in your juicer until power is turned ON and the motor is start spinning.
• Allow juicer to run for a few seconds before start juicing.
• Do not force the food into the juicer. Allow the food to drop through slowly & steadily using the pusher.
• Any fruit or vegetables that be fit will the feeding tube can put through whole. Cut the food if it is too big in order to fit in the feeding tube.
• Remove large pits such as peach, mango, etc., as this will damage the blade and possibly the juicer.
• Let the juicer run for a few seconds before turning off to allow any excess juice to be extracted from the pulp. Once turned OFF, wait until the juicer has come to a complete standstill and has fully cooled before disassembling.
• Do not recommend using overripe fruit as it will leave too much pulp in the filter and clog the juicer.
• Do not pour liquids into the appliance at any time unless you are following instructions/recipe for making soy, rice, or nut milk.
• When using small or thin fruits or vegetables, add many of them at the same time. For example, insert 2 or 3 carrots at a time into the feeding tube for best results.
• When juicing herbs or wheat grass, wrap them in larger leafed vegetables such as spinach, cabbage, etc., and follow by a fruit or vegetable that contains an abundance of juice such as pineapple, apple, etc.
• When juicing carrots that are not the same size, do not use pusher until the largest carrot has been processed. Once they have the same size, you can use pusher to continue until carrots have been processed.
• Denser vegetables (i.e. beets) and fibrous vegetables (i.e. celery) should be chopped and fed slowly into the feeding tube to reduce clogging.

Cleaning & maintenance

• ATTENTION! Always disconnect the appliance from the electrical mains and cool down before storage, cleaning & maintenance.
• Do not use water jet or steam cleaner for cleaning and do not push the appliance under the water as the parts will get wet and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this can adversely affect the life of the appliance and result in a dangerous situation.
• Food residues should be regularly cleaned and removed from the appliance. If the appliance is not cleaned properly, it will reduce its lifespan and may result in a dangerous condition during use.
• DANGER OF INJURY! Care should be taken when handling the sharp cutting blades during cleaning.

Cleaning

• Clean the cooled exterior surface with a cloth or sponge slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned before and after use.
• Avoid water contacting the electrical components.
• Do not immerse beyond the level.
• Never use aggressive cleaning agents, abrasive sponges, or cleaning agents containing chlorine. Do not use steel wool, metallic utensils, or any sharp or pointed objects for cleaning. Do not use petrol or solvents!
• Pusher, lid with feeding chute, basket assembly, bowl and pulp container could be cleaning by immersed in warm, mild detergent for about 3-5 mins and rinsed under running water.
• No parts are dishwasher safe.

Maintenance

• Check the operation of the appliance regularly to prevent serious accidents.
• If you see that the appliance is not working properly or that there is a problem, stop using it, switch it off and contact the supplier.
• All maintenance, installation and repair work must be carried out by specialised and authorised technicians, or recommended by the manufacturer.

Transportation and Storage

• Before storage, always make sure that the appliance has been disconnected from the power supply and completely cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could damage it.
• Do not move the appliance while it is under operation. Disconnect the appliance from power supply when moving and hold it at the bottom.

Troubleshooting

If the appliance does not function properly, please check the below table for the solution. If you are still unable to solve the problem, please contact the supplier/service provider.

Safety instructions

• Only use the appliance for the intended purpose it was de-signed for, as described in this manual.
• The manufacturer is not liable for any damage caused by incorrect operation and improper use.
• 
  RISK OF ELECTRIC SHOCK! Do not attempt to repair the appliance by yourself. Do not immerse the electrical parts of the appliance in water or other liquids. Never hold the appliance under running water.
• NEVER USE A DAMAGED APPLIANCE! Check the electrical connections and cord regularly for any damage. When damaged, disconnect the appliance from the power supply. Any repairs should only be carried out by a supplier or qualified person to avoid danger or injury.
• 
  When positioning the appliance, route the power cable safely if necessary to avoid unintentional pulling, being damaged, coming into contact with the heating surface, or causing a tripping hazard.
• 
  As long as the plug is in the socket the appliance is connected to the power supply.
• 
  ALWAYS switch off the appliance before disconnecting from the power supply, cleaning, maintenance or storage.
• Only connect the appliance to an electrical outlet with the voltage and frequency mentioned on the appliance label.
• Do not touch the plug/electrical connections with wet or damp hands.
• Keep the appliance and electrical plug/connections away from water and other liquids. If the appliance falls into water, remove the power supply connections immediately. Do not use the appliance until it has been checked by a certified technician. Failure to follow these instructions will cause life threatening risks.
• Connect the power supply into an easily accessible electrical outlet so you can disconnect the appliance immediately in case of emergency.
• Make sure the cord does not come in contact with sharp or hot objects and keep it away from open fire. Never pull the power cord to unplug it from the socket, always pull the plug instead.
• Never carry the appliance by its cord.
• Never try to open the housing of the appliance yourself.
• Do not insert objects into the housing of the appliance.
• Never leave the appliance unattended during use.
• This appliance should be operated by trained personnel in kitchen of the restaurant, canteens or bar staff, etc.
• This appliance should not be operated by persons with reduced physical, sensory or mental capabilities, or persons that have a lack of experience and knowledge.
• This appliance should, under any circumstances, not be used by children.
• Keep the appliance and its electrical connections out of reach of children.
• Never use accessories or any extra devices other than those supplied with the appliance or recommended by the manufacturer. Failure to do so could pose a safety risk to the user and could damage the appliance. Only use original parts and accessories.
• Do not operate this appliance by means of an external timer or remote-control system.
• Do not place the appliance on a heating object (gasoline, electric, charcoal cooker, etc.).
• Do not cover the appliance in operation.
• Do not place any objects on top of the appliance.
• Do not use the appliance near any open flames, explosive or flammable materials. Always operate the appliance on a horizontal, stable, clean, heat-resistant and dry surface.
• The appliance is not suitable for installation in an area where a water jet could be used.
• Leave a space of at least 20 cm around the appliance for ventilation during use.
• 
  Keep all ventilation openings on the appliance free from obstruction.

Special safety instructions

• This appliance is intended for commercial use.
• 
  Take great care when handling the cutting disks. Wear protective gloves (not supplied) if necessary.
• 
  BLADES ARE SHARP. KEEP HANDS AWAY!
• Do not operate the appliance without load to prevent overheating.
• 
  ALWAYS switch the machine off and disconnect the power supply before touching any motoring parts.
• The supply cord cannot be replaced. If the cord is damaged the appliance should be scrapped.
• Do not use the appliance if the rotating sieve or the protecting cover is damaged or has visible cracks.

Intended use

• This appliance is intended to be used for commercial applica-tions, for example in kitchens of restaurants, canteens, hospital and in commercial enterprises such as bakeries, butcheries, etc., but not for continuous mass production of food.
• The appliance is designed for extracting juice from vegetables or hard fruits such as apples, etc. Any other use may lead to damage to the appliance or personal injury.
• Operating the appliance for any other purpose shall be deemed as a misuse of the device. The user shall be solely liable for improper use of the device.

Grounding installation

This appliance is classified as protection class I and must be connected to a protective ground. Grounding reduces the risk of electric shock by providing an escape wire for the electric current.
This appliance is fitted with a power cord with grounding plug or electrical connections with grounding wire. The connections must be properly installed and grounded.

Hendi B.V.
Innovatielaan 6
6745 XW De Klomp, The Netherlands
Tel: +31 317 681 040
Email: info@hendi.eu

Hendi Polska Sp. z o.o.
ul. Firmowa 12 62-023 Robakowo, Poland
Tel: +48 61 658 7000
Email: info@hendi.pl

Hendi Food Service Equipment GmbH
Ehring 15
5112 Lamprechtshausen, Austria
Tel: +43 6274 200 10 0
Email: office.austria@hendi.eu

Hendi Food Service Equipment Romania S.R.L.
Str. 13 decembrie 94A, Hala 14
Brașov, 500164, Romania
Tel: +40 268 320330
Email: office@hendi.ro

PKS Hendi South East Europe SA
5 Metsovou Str.
18346 Moschato, Athens, Greece
Tel: +30 210 4839700
Email: info@pks-hendi.com

Hendi Italia S.R.L.
Via Leonardo da Vinci 4
39100 Bolzano (BZ), Italy
Tel: +39 800 727 438
Email: office.italy@hendi.eu

Hendi HK Ltd.
1208, 12/F Exchange Tower
33 Wang Chiu Road, Kowloon Bay, Hong Kong
Tel: +852 2154 2618
Email: info-hk@hendi.eu

Find Hendi on internet:
www.hendi.com
www.facebook.com/HendiToolsforChefs
https://www.linkedin.com/company/hendi-tools-for-chefs/
www.youtube.com/HendiEquipment

Changes, printing and typesetting errors reserved.

Documents / Resources

References

• http://www.hendi.com
• http://www.facebook.com/HendiToolsforChefs
• HENDI - Tools for Chefs - YouTube

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download HENDI 221105 - CENTRIFUGAL JUICE EXTRACTOR Manual